Comments on: Simple Xbox 360 rapid fire mod

By: MvZiC MaN

MvZiC MaN — Fri, 10 Feb 2012 01:10:39 +0000

where did you attatch the wire….??

By: jj

jj — Sun, 22 Jan 2012 00:18:32 +0000

IT DOES ONT WORK! i have tried it in every way possible! WTF!

By: Th3badwolf

Th3badwolf — Thu, 12 Jan 2012 02:01:37 +0000

wire name? really?

By: Delithicus

Delithicus — Mon, 07 Nov 2011 02:17:49 +0000

I have a question though…I put the switch connected to the middle trigger port and another wire to the rumble port. It worked fine for weeks then all of a sudden the trigger is stuck on. I even took the switch out and its still staying on, the only way to make it stop is to bridge the middle trigger port to the bottom trigger port. BUT that makes other buttons fire off – any suggestions?

By: Delithicus

Delithicus — Mon, 07 Nov 2011 02:14:46 +0000

Rob, youre using the wrong kind of switch yours sounds like a closed switch you need an open one.

By: scott

scott — Wed, 02 Nov 2011 00:13:33 +0000

you would offcialy find them at radio shack they are called monumentary switches they r really small it has four tabs and a tiny button in the middle of the square

By: JoeCooler

JoeCooler — Thu, 18 Aug 2011 00:41:41 +0000

You have most likely installed a “Closed” push button instead of an “Open” button. Closed switches will disconnect when pressed. Open switches will connect when pressed.

By: Jake

Jake — Sun, 05 Jun 2011 09:09:54 +0000

Uh, I’m vary nervous ofdoimg this to my controler, what wire do I use? Also, can I PLEASE have a JPG to where to solder?

By: Damon

Damon — Thu, 19 May 2011 07:03:08 +0000

Hey i just wanna know if that gel you dipped the wire in before you soldered it the the point is that so it can be soldered without solder wire or do you just not need solder wire?

By: handy helper

handy helper — Wed, 06 Apr 2011 00:57:44 +0000

http://www.se7ensins.com/forums/topic/50899-how-to-make-a-rapid-fire-controller/

By: Taylor

Taylor — Sun, 27 Mar 2011 19:48:14 +0000

Where do I put the switch? And is there a way to make this work so I pull the trigger and rapid fire?

By: bihlcosby

bihlcosby — Mon, 14 Feb 2011 20:47:11 +0000

how do you know if its a tp3 and what type of wire did you use

By: allurbases23

allurbases23 — Mon, 14 Feb 2011 20:36:19 +0000

this only works for tp3 controllers that is why when u press the button it fires one shot only and as for the momentary switch i salvaged mine out of an old ps2 controller (R3 “knife on CoD” button located under joystick ,tip on soldering try soldering wires onto momentary switch first then (with top of controller casing off turn on the controller and start a game”ex. MW2″ hold the wires to the soldering points and press the button to test it, if it doesn’t fire full-auto, the wires are probably backwards and when opening your controller try using a small phillips head screwdriver to break the security pins on the screws then use a T9 bit to unscrew them

By: tom

tom — Wed, 09 Feb 2011 18:03:59 +0000

mike u can buy the trigger at any hardware store!

By: Mike

Mike — Wed, 22 Dec 2010 16:02:31 +0000

Hi im just wondering how i get the “trigger”? Where can i buy it? thankful for answer