Going camping? You’ll need an extra backpack to carry this flashlight along the way. On the business end you’ll find 500 five millimeter super-bright white LEDs, on the opposite end there’s ten times the number of controls you’d expect on a flashlight. At full power, the LED array pulls down 50 Watts, making us question the battery life of the unit. Check out the walk-through after the break. The LEDs are mounted on proto-board, making for some extreme point-to-point soldering. During the control demonstration there’s a background noise like a jet powering up, what’s that all about?
While this terrific torch brings a grin to our faces, we wonder if it wouldn’t do better as a vehicle mounted illuminator. Or if a microcontroller was tossed into the mix some creative code could make this a pretty powerful yet non-lethal weapon.
[Keith] built this aluminum-plate heated build stage for his MakerBot 3D printer. We just saw a different MakerBot heated build stage yesterday that relied on glass as the printing surface. Keith’s design is similar to the aluminum RepRap bed but scaled down for the MakerBot. He had a piece of aluminum machined the to correct dimensions, and perfectly flat to use as the printing surface. The yellow surface is caused by Kapton tape applied to the top of the plate. This heat-resistant covering is perfect to print on, resulting in glossy smooth surfaces that are easy to remove once the printed part has cooled. He’s working on improving his mounting technique to achieve prefect level so that he can print without a raft.
[Keith's] writeup is phenomenal. He’s sharing knowledge in a way that is useful even if you’re not building the exact same kind of project. Follow his lead with your own write-ups, then let us know once you’ve posted them.
Driven by the relentless nagging encouragement of the Hackaday commenters, [Johndavid400] has improved the Lawnbot 400. No longer does it just sport a makeshift wooden shelf. he now has a wheel barrow attachment. It looks quite sturdy as long as that front hinge holds out. There is an actuator coming in the near future for dumping the contents as well. Also, we suspect that might be a shovel in this picture.
Here at Hackaday, we may be somewhat divided in our opinions of Anime and Manga. We were all pretty impressed by this robot build(translated) though. We’re not totally clear on who actually did this build, but we can see a few pictures and a video on the site. The original doll looks to be roughly 3 or 4 inches tall, judging by the Eeepc keyboard that it is standing on. We counted 7 servos stuffed into this thing with a controller board hiding in the back of its hair. You’ll have to watch the video to see most of the details. It looks like there is one in the head, one in each shoulder, both hip joints, and both feet. Though the motion at the end of the video is limited, we still think it is impressive. Creepy, but impressive.
note: the video is not embedded in the translated version. Just go to the non translated to watch it.
We may be good at soldering but when it comes to hauling topsoil our scrawny arms quiver. [Johndavid400] did the smart thing here by letting the machine do all the work. Instead of hauling an entire truckload of dirt across the yard one wheelbarrow at a time, he built a shelf on the top of his Lawnbot400. We saw this lawnmower Arduino-powered, remote control mower back in November. The addition of its ability to handle some of the manual labor makes it the perfect backyard hack.
This heated build stage seeks to make 3D printing with the MakerBot a little easier. When hot ABS or PLA meet the cold, cruel world they have a tendency to warp. This was concern for [Devlin Thyne] when he was developing our Hackaday badges. What you see above is 10 Ohm nichrome embedded in clear silicone, then sandwiched in between two plates of glass. The device is made to interface with the MakerBot and includes a thermister for temperature sensing. With a small firmware upgrade you can now set the build stage temperature which should make larger printed objects a bit easier to deal with. A while back we saw a hotbed for the RepRap, but this implementation should be cheaper and easier for the smaller MakerBot applications.
The impossible has happened. While that may sound a bit over dramatic, the project itself was titled “the impossible project”. What is it that is so impossible? The revival of Polaroid instant film. This is not a newer, digital alternative, this is film you can actually buy and plop into your old Polaroid camera. What’s the big deal? All they had to do was start producing it again right? Not really. They’ve completely re-engineered it from scratch. That’s pretty impressive. We had heard, early last year, that they were going to attempt it, and we’re pleased to see that they’ve succeeded.
That being said, a handheld, home hacked digital instant picture device sounds kind of cool. It would probably be an easy one to build too.
[Chris Neal] is starting his hacking career young. He built this fan-powered skateboard for his fourth grade ‘Invention Convention’. The ideas were his own but he had some help with the construction from his uncle who owns a repair garage. On the back of the board there’s a motorcycle battery that powers the fan. We’re not sure where that fan came from, but apparently it can push a rider at about 3-5 MPH. [Chris] scored a free MacBook pro from this hack after being featured on the Ellen DeGeneres Show.
