Once again it’s time for you, the sharp-eyed readers of Hack a Day, to decide whether the following video demonstrates technology at its finest, or if it is complete hogwash. This edition of Real or Fake? is brought to us by Hack a Day reader [Wizzard] who sent us a link to “The Invisible Camera“

Watch the video embedded below to see the unveiling of this camera as well as a discussion of its new, revolutionary technology by its creator – photographer Chris Marquardt. The camera is composed of a simple, non-moving lens mounted in a completely transparent box made of specially polarized glass. This glass is supposed to align the ambient lighting, which amplifies the energy coming through the lens, in order to expose the special film they created for the camera.

The film was developed using standard film “combined with innovations in chemistry” to produce ultra-low sensitivity image media, which the creators are calling “Directionally Desensitized” film. This film can be handled in full light, as it is only sensitive to the high-energy light directed on its surface by the aforementioned lens. It is claimed that due to this special film, the camera goes beyond the Megapixel, past the Gigapixel, and captures images in Terapixels.

Now, call us skeptical, but isn’t it a bit early for April Fools jokes? We just can’t imagine any scenario where holding a piece of film in the sun as shown in the video would not cause it to be exposed in at least some areas due to the massive amounts of reflected light in the environment.

What’s your take?

Read the rest of this entry »

[Reinventing Science] needed a project that he could use to test out his skills on a new CNC routing machine he recently acquire. He settled on building a PC case using easily obtained materials. What he ended up with is the clean-looking case seen above that was machined from materials you can pick up at the home store.

The bulk of the case is made from extruded PVC which is designed to perform like solid wood trim. He picked up one piece of the ‘lumber’ and cut out the front, back, top, bottom, and drive bay bezel. We expected the joints between the horizontal and vertical pieces to either be butt joints, or rabbits. But [Reinventing Science] wanted a cleaner look and managed to mill mortise and tenon joints. These are strong joints that leave a very nice finished look. Since the material is designed as a lumber replacement it shouldn’t be too surprising to see drywall screws used as the fasteners.

In addition to joinery, some other CNC tricks were used. The sides of the case were cut from clear acrylic, with a decorative bead milled in the surface. There’s also fan ports cut in the top and vents on the bottom, as well as some engraving with the name of the project just above the optical drive. The wood-grain embossing makes for an interesting final look; we’d like to see how this takes a few careful coats of paint.

If you’re interested in the CNC hardware used, take a look at the unboxing post that shares a few details.

What is the best thing about making a computer program that targets and kills anything that enters its sight? Why giving it a weapon, of course! No, we are not talking for real, but the next best thing, an Autonomous Paintball Sentry Gun.

The autonomous part of the device comes from a pc on the sideline and is fed input though a standard webcam. The feed is ran though a processing script where, once accustomed to the background has the option to fire at anything it sees moving, or a nice point n click manual mode.

The Arduino part is in a the role of driving the servo motors for X/Y movement and a trigger and is powered by a fist full of D cell batteries to give plenty of time for fun. Also, be sure to check out our other sentry guns, one using Microchip PIC, and another sporting a super compact computer running Ubuntu

3D holographic fog display

Some researchers in Japan are hard at work building a 3D volumetric fog display that would allow you to live out some of your Leia-related Star Wars fantasies. Using a column of fog and three projectors, they were able to create a display that looks three-dimensional from any angle. It might be a while before the technology hits your living room, so don’t clear your calendar just yet, Obi Wan. [via Neatorama]

The Claw – a three-fingered robotic gripper

Instructables user [AntMan] has been hard at work revising his robotic claw gripping mechanism. Laser cut from wood, this servo-driven claw can easily grasp small objects with little effort. We can’t wait to see someone build a version from milled aluminum!

Ben Heck’s retro Xbox 360

[Ben Heck] is at it again, and has recently given the Xbox 360 a sweet retro makeover. Taking inspiration from gaming consoles of the 70′s, he converted an Xbox 360 into a laptop-style portable (again), but this time with the look and feel of an old Atari 2600. Retro gamers rejoice, you can now get your Xbox on while enjoying the sweet simulated wood-grain you grew up with.

Rocket-based ice fishing notification system

What fun is ice fishing if you have to sit outside freezing your butt off? We’re assuming that was the driving thought behind [Mike's] rocket-based ice fishing rig. A model rocket is attached to his fishing sledge, which is triggered when a fish is detected on the line. Using a low-tech detonator, the rocket lets him know it’s time to check the lines. Now only if we could get the fish to fillet themselves…

Case modding video series hits the web

The “Mod Men” is a fairly new web series that takes you out of the basement and into the garage for some professionally constructed case mods. Described as “American Chopper for geeks with a dash of This Old House”, the creators aim to showcase over-the-top case mods with a professional flair. They already have three episodes under their belt, all of which are available on their site.

This functioning mechanical irs is made from paper templates, foam core poster board, old credit / gift / etc cards, paper clips and masking tape. First, patterns are designed and multiples are printed and laid out to make the 10 parts needed. Two rings are cut out of foam board and a third ring is cut into wedges to form a cam mechanism on top of one of the other two rings.

Twelve shutters are then cut from the credit cards, and small pieces of paper clip are glued to each end and both sides. One side rides the cam mechanism the other side is punched through the final ring.

We found it to be an interesting project that should be pretty easy for just about anyone to replicate (now that its all figured out for us), and besides, you never know when you might stumble across a small box of hotel key’s with a defunct pizza parlor’s advertisement on the back.

Sometimes milestone birthdays can be a bit depressing. 30 is rough, and 40 tougher – but 50…that’s a big one!

[Ryan’s] uncle is going to be turning 50 shortly, and in the interest of good-natured fun, he has constructed a handy birthday countdown timer for his uncle, lest he forget (or tries to avoid) the big day.

The device displays the amount of time left before his uncle’s birthday, playing an audio clip of “Don’t fear the Reaper” when the clock strikes 00:00. This is accomplished by using the MSP430′s internal clock to keep time, while also interfacing with a Nokia 3310 LCD panel to display the countdown timer. The music is provided by the circuit board from a greeting card he gutted for the project, which was wired to the LaunchPad in order to be triggered at the right moment. Everything was crammed inside an Altoids tin, as you can see in the picture above.

Though not overly complicated, it’s a fun little project, and we’re hoping his uncle gets a big kick out of it. Once his birthday has come and gone, [Ryan] plans on converting the piece into a permanent desktop clock for his uncle.

Ever wish you could DJ on the fly while using equipment that your already wearing? Well neither have we but heck now we can, cheaply and easily with the Wristwatch Turntables. While being functional and stylish, this interesting project is fairly easy to construct and if need be, even sports a full function digital watch.

The audio electronics are donated by a pair of talking / musical  greeting cards. Both, “record your own” and “just deal with what we give you” types, though which ones you choose is left up to your taste. The greeting cards are then cut apart for their hidden goodies and then a little circuit bending action is performed to monkey with the amplifier of the sound module.

Potentiometers are added, buttons are relocated, and everything gets housed in a small box, with a wristwatch ran down the middle so you can wear the whole deal and blast your funky beats anywhere you may be. Join us after the break for a quick video.

Read the rest of this entry »

Instructables user [Jones Electric] has been quite busy lately, building a radio-frequency range finder. Built as part of a German youth science competition, he and his partner built a pair of transmitter/receiver modules that can be used to measure distances of up to a mile (~1.5km). Their argument for radio-based rangefinders is that laser rangefinders are obviously limited to line of sight, whereas their range finders are not.

To determine the distance between the two stations, the base station is triggered, which starts a counter and sends a 433 MHz signal to the second station. When the second station receives the signal, it in turn broadcasts an 868 MHz signal, which is received by the base station. The total distance between the points is then calculated based upon the round trip time of the two radio signals.

[Jones Electric] claims that the range finder is relatively accurate, with a deviation of up to 5 meters per measurement, and that the accuracy could be increased by adding a higher frequency crystal to the timing circuit.

We are pretty sure using these two frequencies in the US without a license is not allowed, though we are unsure of the usage laws in Germany, where this was constructed.