Here’s a no-PCB Arduino that doesn’t obscure the DIP footprint of the AVR chip. It’s built on an ATmega88 chip, and includes a programming header, reset button, a couple of filtering caps, and an LED. This is modeled after the Lilypad hardware, and fits nicely on top of the plastic case of the microcontroller, allowing it to be used in a breadboard or DIP socket. You can see a walk through of the components in the clip after the break.

We don’t really need most of the components on top of the chip (especially the status LED on the SCK line), but there are several things that we like about this. First off, the programming header is extremely nice. We could see this coming in handy for prototyping where you don’t want to add a header to your final design. Just use a chip socket, and this chip while you’re developing firmware. Once everything is dialed in, program a naked chip and swap the two. The same goes for the reset button, which is nice when working on firmware but may not be necessary in your final design.

This is quite an old project, and we’ve actually seen a successor to it. This is Rev. 2 and we looked in on Rev. 7 back in March. That one is a full Arduino, but the circuit board has no substrate.

[Thanks Panikos]

We got a hold of some DS3232 RTC chips in a 20-pin SOIC package. We’d like to have one that is breadboard compatible for easy prototyping but when we searched for SOIC20W breakout board artwork we found none. We used Eagle to design our own and you can see the finished product above which we made using the toner transfer method and cupric chloride.

You’ll find the artwork after the break in case you need to make your own breakout board some day. If you know of surface mount breakout board artwork that is freely available please leave the link in the comments for future use, or send it to us on our tips line and we’ll add it to the post.

Incidentally, the DS3232 is the same as the DS3231 used in the ChronoDot but with the addition of some SRAM. We’ll let you know if we come up with an interesting project for it.

Update: We added 28 SSOP to DIP artwork submitted by [Paul Dekker]

20-PIN SOIC to DIP

28-pin SSOP to DIP [Thanks Paul Dekker]

Here’s a Christmas tree project we can get behind. The “tree” itself is made of twisted pairs of insulated copper wire.  At the end of each pair a surface mount LED has been soldered between the two conductors.  All of the wire limbs converge into a 4×4 matrix. One tree uses a prototyping shield and an Arduino, the other tree is just using an ATtiny2313 microprocessor. Take a look at the twinkling tree in the video after the break.

This artful creation uses one color of LEDs.  We’d love to see future improvements that incorporate multiple colors, enhance the fading effects, and perhaps add some interactivity such as pulsing to an inspiring rendition of Chestnuts Roasting on and Open Fire (which, consequently, is called “The Christmas Song“).

[Gio] enjoys using vacuum tubes in his projects. He designs the circuits using a CAD program but was finding that there is no substitute for actually building a prototype before heading to a final design. To make this process easier, he built his own tube prototyping station.

At the top of the board he’s got three different sizes of tube sockets with the pins from each wired as common. The nine pins from the sockets break out to a terminal strip where they can be interfaced with a solderless breadboard. For added versatility he’s included terminals to tap into some RCA jacks, as well as a 100 kOhm variable resistor. We’d bet this is not something that you can find ready-made, but it sure does look a whole lot better than a workbench full of components alligator-clipped together.

Our friend [Garrett Mace] from macetech has finished a prototype of a new shield which allows the Arduino (or any other microcontroller with I2C) to add 64 digital I/O pins using only 2 of the analog pins. Currently he only has a few pre-production boards, and rather than selling them he is throwing a contest to win them. The contest is looking for people who have a specific project in mind that could use the centipede, and on Friday November 13th he will pick his favorite two. To submit an idea, just head over the Arduino forums and post an idea complete with details and relevant schematics, etc.

We will be sure to follow up with the winners of the contest, as well as let you all know when the Centipede Shield makes it into production.

In August we covered a wireless electricity presentation from the TED conference. Now Sony has put out a press release on their wireless flat panel television prototype. The device is capable of operating without audio, video, or power cables connected to it. This is possible at distances up to 50cm at efficiencies as high as 80%.

As was talked about in the comments of the other article, the efficiency compared to that of a cable doesn’t blow our socks off. But this does show mainstream development of this technology. We hope to see advances in both efficiency and distance. We also look forward to that small black box (which we presume facilitates the energy transfer) being integrated into the TV’s body.

[via Gizmodo]

Do you find that the capabilities of your current microcontrollers are holding you back when you try to take over the world? Moving up to ARM7 architecture will put your projects in the same arena with the iPod and the Nintendo DS.

The BlueBoard-lpc214x is a prototyping board with a lot to offer. It incorporates two RS232 connections, USB, VGA, SD card slot, piezo buzzer, JTAG, audio out, PS2 keyboard connector, and a 2-line character LCD. The processor is an NXP Semiconductor LPC2148 with 512KB of programming space and 32+8KB of ram. The board also includes a 256KB i2c eeprom. This is a lot of prototyping power, but the low purchase price knocks our socks off: $40.90! Sadly, shipping would cost us another $20.43 but that’s still a lot of functionality for around $60.

Sample code and schematic are available for download. All of the pins for the microcontroller have jumpers and there are rows for pin headers around the processors if you want to patch in your own hardware. We’ve seen other ARM boards that make use of pre-existing shields. We would love to see someone remove the processor and implement Arduino-like shields for different processors outside of the LPC214x series. Promo video after the break.

[via ScienceProg]

[Thanks CH]

We’ve seen  Z80 processor based computers before but they usually use a printed circuit board to easily and reliably connect all the components. [Marton] sent us his Z80 based computer from a while back that is built entirely on prototyping board. He made his own video board that utilizes a TV as the monitor and his own mainboard incorporating a keyboard controller. The system runs at 4 MHz, has 32k of ram, and runs [Marton's] own system software which he has posted. Its quite impressive and we love the protoboard porn with thousands of grey wires running everywhere.

[Marton] used the resources on [Hans Summers'] site for his project. Make sure to check it out if you’re interested in a broader background concerning DIY Zilog Z80 computers.

Generation 2.0 of RepRap, the self replicating 3d printer, is approaching realization. Code named “Mendel”, the new design will be wedge shaped rather than a box which offers a few benefits. The overall design is smaller than the original RepRap but the printable area is larger. This means more functionality with less building material. With each new generation of this project the assembly gets easier and total parts price drops making the RepRap available to a much wider audience.

The RepRap blog has put forth some design specs, a picture of the assembled prototype, and has links for general assembly information (ZIP). We won’t see a finished version of this released for a few months but so far it looks like a big leap forward.

[Knut Karlsen] put together a prototype set of solar rechargeable batteries. He always seemed to have batteries laying around on his worktable and figured they might as well be charging. The flexible solar cells were given to him by researchers at the IFE and are rated at 1.8V. He used superglue to secure them to the C cells. A silver conductive pen plus flat wires from a Canon lens connect the solar cells to the battery terminals. The batteries just trickle charge for now, but he’s going to try to build cells with built in charge controllers in the future.

The last time we checked in on Pandora it was just being shown in dev unit form. Embedded above is a video of the first case prototype. It doesn’t have any components yet, but it definitely looks like a good formfactor with a lot of potential. The Pandora is a Linux based portable game console with an 800×480 touchscreen.

[via Gizmodo]

[Alex] was frustrated by the amount of time it took to start prototyping with an AVR ATtiny. To make things easier, he built headers that carry the 8 and 20 pin chips and plug directly into breadboards. The boards include a 6pin ISP header, resonator, pull-up resistor, reset, and blocking caps. The ATtiny2313 version also has a serial connection header. This is a prototype though, and he forgot to route one of the connections. He plans on having a large batch of boards ready for next month.

If you haven’t checked out SparkFun Electronics’ prototype collection yet, you’re missing out. They unearthed many of their old prototypes and published them to show what kind of mistakes could be made. You’ll see plenty of errors and get hints on what to look for while developing your own hardware. This pairs well with their Design for Manufacture post. Along with the pile of broken board iterations, they also walk through how the company developed. Finally, they specifically cover the individual iterations of the BlueSMiRF.

One of the interesting modules in the gallery that never saw full release was the SparkFun Toys line pictured above. The individual units used the standoffs as the power and data bus. The four posts were arranged so they could only be connected in one orientation: power, ground, TX, and RX. It’s an interesting idea that seems like it might be worth exploring further. SparkFun says that it worked fine, but didn’t feel they had the resources to market it to the intended audience.

When you’re prototyping a new project, sometimes all you need is a switch. The folks at oomlout were tired of constantly having to rewire things, so they built a universal switch box for the Arduino. It has five potentiometers plus three switches. They’ve put together a software package that monitors the switches and can show you a live view of the knob positions. Have a look at the video below for a demo.

The writeup actually hints at what we can only assume is the next kit they’re releasing: a robot arm.