Hack a Day » tubes

High Voltage Hacks: A 1000 Watt tube amp

Brian Benchoff — Fri, 26 Aug 2011 13:00:39 +0000

Normally when we hear of a Champ guitar amp, we think of a sweet-sounding rig that puts out 6 Watts through an 8-inch speaker. [John Chambers] of Champ Electronics wanted to build a true champion for the field of battle and came up with The Champ 1000 Watt Tube Amp, an amplifier that probably puts out enough heat to keep an igloo warm.

The amp is based on 807 valves. With some clever engineering [John] managed to coax 100 watts out of a pair of 807s, so the entire amp “only” requires 20 power tubes. The build log shows some pretty impressive examples of electrical prowess. We can’t recall the last time we featured a build with point-to-point wiring on tagboard, and [John]‘s work is some of the best we’ve ever seen.

[John] has been working on this amp off and on for a few years now, but he should be wrapping up the build sometime soon. We haven’t seen this amp in action, but we imagine it would look something like this 36×10 monstrosity. Send us a message or post a comment if you can find a video and we’ll put it up.

Filed under: hardware, musical hacks

Tube amp monitor

Juan Aguilar — Tue, 24 Jun 2008 02:00:00 +0000

Sparkfun contributor [Pete] really loves tube amps, but he’s a very safety-conscious guy who doesn’t like being electrocuted. This is a problem, since tube amps are usually very high voltage, and a small mistake can be fatal. To deal with this voltage issue, he built a tube amp with a control system built around a 6DOF v3 controller board. The control system is there mainly in case of a failure, automatically shutting off the high voltage transformer in any such event. It has the added benefit of filtering any 60Hz noise from getting into the audio, which happened before he installed the control system.

In addition to regulating power, the controller board also monitors bias points in the output tubes and displays its diagnostics on an LCD. Aside from getting great sound from the tube amp, [Pete] made it look great too, installing colored LEDs under the tubes. We love his design: just because safety comes first it doesn’t mean cool-factor can’t come in a close second.

Multiband Nixie VU meter

Eliot — Sat, 14 Jun 2008 04:50:00 +0000

This VU meter project by [Daniel Naito] is a great piece of Russian electrocouture. It’s made up of 14 Nixie tubes that display seven frequency bands for the two audio channels. He found this similar project, but wanted to keep the cost low by avoiding such exotic ICs. First, the two input channels are amplified and then split using seven bandpass filters covering 60, 150, 400, 1000, 2500, 6000, and 15000Hz. Then, the AC audio is converted to DC. The final stage converts the logarithmic scale to a linear output. Besides the semirare Nixie tubes, the majority of the parts are just cheap opamps and comparators. The post is an excellent read and you can see it in action in the video below.

UPDATE: Yep, it’s a repost. I’m awesome like that. The True RMS Plasma Vu-meter seems to be new to us though.

[thanks meh]

Nixie tube VU meter

Will O'Brien — Thu, 27 Mar 2008 18:01:00 +0000

[Daniel] sent in his Nixie tube VU meter. It uses 14 Russian IN-13 Nixie bar-graph tubes. He built a custom circuit to amplify, filter, smooth and feed a voltage divider to assign signal levels to segments and finally some high voltage transistors to drive the tubes. The circuit looks pretty big, but it’s repeated for each tube – so he worked hard to keep the cost down as much as possible. Now this just needs to live on the front of a massive tube amplifier.

Tiny Oscilloscope

Will O'Brien — Tue, 31 Jul 2007 06:31:00 +0000

This little o-scope is built entirely using valves (tubes), built by [Ian Wilson] and [Hans Summers]. [Hans]‘ site covers everything from monitor gutting to a Z80 viscometer, it’s worth taking some time to poke around. Thanks to [Elliot] for sending in this one on the tips line.