The Force Is Strong With This Christmas Tree Light Show

December 5, 2011 by Mike Nathan 6 Comments

[Zach] is a huge Star Wars fan, and in addition to the array holiday decorations that adorn his house, he says that his wife is nice enough to let him put up a Christmas tree full of Star Wars ornaments. For the past few years, the tree sat in the corner of the room unlit, but his wife thought that it should have some lights this year.

His wife came home with a small string of battery-operated lights, but [Zach] wanted something with a bit more geek cred. He decided to program the lights to play the Star Wars theme song, translating the tune’s pitch to light intensity.

He dug through his bin of electronics and found an MSP430 along with a small target board that would do the job nicely. He sat down with some sheet music, translating the notes to PWM values, resulting in the light show you see below.

While his wife provided a lovely violin accompaniment to the tree, we think that a small audio module would make a great addition to the tree next year.

Continue reading “The Force Is Strong With This Christmas Tree Light Show” →

G-35 Circuit Board Porn

November 29, 2011 by Mike Szczys 13 Comments

[Todd Harrison] took a slew of pictures in his quest to loose all the secrets of the G-35 Christmas Lights. These are a string of 50 plastic bulbs which house individually addressable RGB LEDs. We’ve seen a ton of projects that use them, starting about a year ago with the original reverse engineering and most recently used to make a 7×7 LED matrix. But most of the time the original control board is immediately ditched for a replacement. It’s become so common that you can now buy a drop-in board, no hacking needed. We enjoy the hard look that [Todd] took at the electronics.

The stock controller uses a single layer, single sided board. There’s a resin-blob chip, but also an SOP-20 microcontroller. Since [Todd’s] using several strings of lights on his house, he wondered if it would be possible to improve on the controller in order to synchronize the strands. His investigation showed that the board was designed to host a crystal oscillator but it is unpopulated. Unfortunately you can’t just add those parts to improve the timing of the chip (firmware changes would also be requires). He found that there’s a spot for a push-button. Quickly shorting the pads cycles through the effects, shorting them for a longer time turns off the string of lights. There is wireless control, but it seems that the only functionality it provides is the same as the unpopulated switch.

We enjoyed the close-up circuit board photos, and we like the spacing jig he used to attach the lights to his fascia boards. We’ve embedded a lengthy video about his exploits after the break. Continue reading “G-35 Circuit Board Porn” →

Candy Chucker – Weapon, Or Advanced Halloween Delivery System?

November 9, 2011 by Mike Szczys 10 Comments

Now we know why kids in this neighborhood wear plastic Halloween masks instead of just painting their faces. They’re trying to protect themselves from the onslaught of hard candy spewing out the front of this candy chucking pumpkin.

The mechanism operates very much like a baseball or football throwing device. Now that we think of it, it’s also the same concept as the chicken launcher. There is a feed shoot that drops the projectile into the grips of two spinning chuckers. Those chuckers are built out of a couple of fans, with layers of fabric to account for different sizes and shapes of candy.

The video after the break shows some test firing. We love the sickening ‘whap!’ that the Werther’s Original (or whatever crappy Halloween offering they’re using) makes when it slams into the wall of the room.

This thing’s just begging to be mounted on a parade float, don’t you think?

Continue reading “Candy Chucker – Weapon, Or Advanced Halloween Delivery System?” →

Halloween Hacks: An Evil R/C Clown Car For Terrorizing The Neighborhood

November 5, 2011 by Mike Nathan 4 Comments

Halloween Hacks Banner

terrifying-clown-car

If you had a few too many trick or treaters hitting up your house this year, [phwillys] has a solution guaranteed to keep them from coming back. He was looking for a way to scare the crap out of the trick or treaters this past Halloween, so he constructed a remote-controlled evil jeep to terrorize the neighborhood.

The jeep was built from an old PowerWheels car, and uses a bunch of different motors to get the effect [phwillys] was looking for. He bought a linear actuator on eBay to let him steer the jeep, which is controlled using some motor controllers he had left over from another project. A salvaged car window motor was used to allow evil clown driver to turn from side to side in his seat, while a pair of car seat motors activate the giant claws built into the sides of the vehicle. The jeep’s hood was even turned into a chomping mouth with large teeth using yet another small motor.
[phwillys] also added a water sprayer to the clown’s mouth, soaking any kids in the immediate vicinity, though he was nice enough to mount a leaf blower on the opposite side of the vehicle to help blow them dry.

It really is an awesome creation, we’re sure the neighborhood kids (and parents) got a big kick out of it. Continue reading to see a short video of his scary clown car in action.

Continue reading “Halloween Hacks: An Evil R/C Clown Car For Terrorizing The Neighborhood” →

Halloween Hacks: Motion Sensing Fog Machine

November 4, 2011 by Mike Nathan 6 Comments

Halloween Hacks Banner

motion-sensing-fogger

[monkeysinacan] wanted to add a fog machine to his Halloween display, but he says that the cheaper consumer-grade models are pretty unruly beasts. He cites short duty cycles and tricky fog control as his two biggest gripes with these sorts of foggers. He decided make the fogging process a little more manageable, and modified his to only generate fog when someone was walking nearby.

One obvious concern with this sort of setup is the warm-up time required to get the device ready to produce fog. If it were to only turn on when someone walked by, [monkeysinacan] would miss his mark each and every time. To ensure that his machine was accurate, he rigged it so that the heat exchanger stayed powered on, triggering the fog juice pump as needed.

To do this, he used an ultrasonic sensor similar to, but cheaper than a Parallax Ping unit. Paired with an Arduino, the sensor triggers the fog machine’s pump for 20 seconds whenever anyone gets within 6 feet of it.

While he hasn’t posted video of the modified fogger at work, it sounds like a solid plan to us.

Halloween Hacks: A Jacob’s Lantern Sure To Win The Carving Contest

November 3, 2011 by Mike Nathan 15 Comments

Halloween Hacks Banner

jacobs-ladder-pumpkin

[Matt] entered himself in a pumpkin carving contest this year, even despite the fact that his artistic skills were a bit…lacking. He knew that he had very little chance of winning the contest unless he had a great gimmick to make his creation stand out, so he started brainstorming.

[Matt] figured that since his design would have to be somewhat simple, he needed something eye catching that he could add to the pumpkin after it went under the knife. Like a bolt of lightning, inspiration struck, and he set off to fetch an ignition transformer along with some wire coat hanger.

He built a makeshift Jacob’s ladder that would fit perfectly inside his hollowed out pumpkin, and proceeded to carve the pumpkin with the “Caution, risk of electric shock” logo, familiar to most anyone that works with electronics. You can see the final result in the video below, which we think looks pretty neat. If he didn’t end up winning the contest, we’d be shocked!

Continue reading “Halloween Hacks: A Jacob’s Lantern Sure To Win The Carving Contest” →

Amazingly Realistic Skeleton Prop

November 1, 2011 by Mike Szczys 5 Comments

[Cjmekeel] spent weeks getting his Halloween display ready this year. The centerpiece of his offering is this full-sized motorized skeleton. But there’s a few other gems that he worked on to compliment it. There’s an old-fashioned radio whose dial moves mysteriously and plays a news flash warning of an escaped mental patient. He also spent a couple of dollars to outfit a crow with some glowing red eyes and a servo motor.

But the creepiness of the skeleton means you might not even notice those other props. He started with a rather boring looking plain plastic head and did some real magic to build up the rotting flesh and gaping wounds. Those penetrating eyes don’t hurt either. The head moves on a few servo motors which use random values and sleep periods for disturbingly jerky movements. Check out the video after the break to get a glimpse at what kept kids away from his house on Halloween.

This is just a build log and unfortunately there’s no post yet showing the finished product. If we can get enough information together we’ll try to run a follow-up.

Continue reading “Amazingly Realistic Skeleton Prop” →