Month: July 2013

Briefcase Mill

July 1, 2013 by 8 Comments

briefcase-mill

Take the machine shop with you; that’s the mantra which drove [Ryan] to build this CNC mill in a briefcase. That album will give you a taste of the final product. But you’ll want to dig through two pages of his forum thread starting with this post in order to behold the build process.

The image above is only part way through the fabrication, but we thought it gave the best overall view of his work. It’s missing the cables which connect to the control circuitry in the lid. The bed has also not been installed and this was before he fabricated the protective case for the PCBs.

Getting everything to fit inside of a folding case was quite a trick. Of course he used CAD to make sure it was possible. There are several places where the clearance when closed is about 2mm. We’re shocked by the build quality of the mill itself. It’s a novel idea to make it portable, but the accuracy and reliability of the machine didn’t suffer for the concept.

If you need a desktop mill that’s not quite as portable here’s a project which will dish out some inspiration.

Raspberry Pi Automates Your Tomato Farm

July 1, 2013 by 15 Comments

rpi-tomato-farming

Check out the tomato plants [Devon] grew using a monitoring system he built himself. It’s based around a Raspberry Pi. As far as grow controllers go it falls a bit short of full automation. That’s because the only thing it can actuate is the black water line seen hovering above the plants. But [Devon’s] work on monitoring and collecting sensor data should make it easy to add features in the future.

The moisture sensors pictured above monitor the soil in which the plants are growing. But he also has temperature and light sensors. These are very important when growing from seed and could be used in conjunction with a heating mat for plants that require higher soil temperatures (like pepper plants). The tomatoes are also pretty leggy. Now that he’s monitoring light levels it would be good to augment the setup with a grow light. A long term goal could even be a motorized bed which could raise the plants right up to the bulbs so they don’t reach for the light.

Don’t let the stars in our eyes distract you though. He’s done a ton of work on the project both with the physical build, and in plotting the data collected by the system. Great job!

Continue reading “Raspberry Pi Automates Your Tomato Farm” →

Goodbye Hackaday, I’ll Miss You.

July 1, 2013 by 139 Comments

Farewell Hackaday, the time has come for me to move on. Don’t worry, hackaday will keep going, just like it did when [Eliot] moved on, and [Phil] before him.

I wrote my first post on July 9th, 2008. Since then I’ve had so much fun, and written a total of 1,552 posts (including this one). In my opinion, there is simply no other site like Hackaday.com, our readers are passionate and knowledgeable and it shows, even if some of you are incredibly rude to each other(that’s a sign of passion right?).

While some projects stand out in my mind, it is the people I have enjoyed the most. The people I met when I went to all the different hackerspaces, my co-writers[Mike Szczys] and[Brian Benchoff], past hackaday employees, our commenters,  and even my boss [Jason Calacanis].

If you want to find me, I’ll be at calebkraft.com or on facebook or G+. I have a twitter too, that I guess I’ll start using today.

Join me after the break just one more time while a take a trip down memory lane with a few of my favorite moments from the last few years.  Oh, and yes, I think saying “after the break” is stupid. What else do you say though?

Continue reading “Goodbye Hackaday, I’ll Miss You.” →

Working With Very Cool LCD Modules From Sharp

July 1, 2013 by 11 Comments

LCD

Here’s some interesting hardware for you: Sharp came out with a very cool series of LCD displays, gong by the name Sharp Memory LCD. Not only are these displays very low power – on the order of about 5 microAmps to keep the display alive – but some of the smaller displays are reflective, making them eminently readable even in daylight. [Mike] decided he’d take a look at these displays and liked what he found.

While these displays are still pretty new, there are a few breakout boards available to make them accessible to desktop tinkerers. The folks at MakerDyne have a breakout board available and there’s one by kuzyatech over on Tindie.

While these displays are readable in daylight and are extremely low power, don’t expect to display LCD video on them anytime soon. The refresh rate is still fairly slow, but you might be able to get away with simple animations with interlacing and so forth. Still, outside of eink, you’re not going to find a better display in terms of power consumption and daylight readability.

Continue reading “Working With Very Cool LCD Modules From Sharp” →

Designing A Marble Track From Scratch

July 1, 2013 by 1 Comment

Woodworker extraordinaire [Matthais] was approached by a toy company to create a ‘marble run’ toy. [Matthais]’ jig-building skills are beyond reproach, so whipping up a prototype for this toy was pretty easy for him.

The basic unit of construction for this marble run is a simple ramp block with inputs and outputs at either end. These were crafted from blocks of wood, with the ramp carved out with a slot mortising machine. To make the side cuts on each block, [Matthais] used his pantograph router and a jig that cuts the wood for marble inputs on either side.

After taking his creation to a hackerspace for some very large kids to play with, [Matthais] found a few problems with his initial design. The blocks didn’t want to stay aligned when marbles were moving down the ramps, so a small mortise and tenon – looking very much like a piece of Lego – were added in several locations on the underside of each block.

Making one of something is relatively easy, but [Matthais] is making hundreds of pieces for his marble run prototype, each interchangeable with another. That’s impressive for something crafted by hand, but when you’re a master at making jigs like [Matthais], everything goes by pretty easily.

3D Printed Pip-Boy, Geiger Counter Not Included

July 1, 2013 by 27 Comments

pip

Yes, we all love portal guns and crowbars, but there’s one piece of video game paraphernalia that could conceivably be a useful piece of hardware for the modern technologist. It’s the Pip-Boy 3000, the wrist-wearable computer from Fallout, and now you can print on on your 3D printer.

All the pieces for this Pip-Boy are available over on Thingiverse. Included in those files are a dozen plastic parts that, when assembled, come together to form a wrist-mounted computer. You could, of course, print out a static image of a Pip-Boy screen for this build, but [dragonator] made a little addition to his model – he put in a space for a smartphone, so all your environmental sensors and inventory management also work with this 3D printed model.

This is far from the first wearable Pip-Boy we’ve seen, but it is the first that’s able to be fabricated on a 3D printer, and comes with the nice bonus of being the best phone case ever. It’s still a lot of work to put this together, but we’re going to say the results are fantastic.

You can check out the demo video of the Pip-Boy below.

Continue reading “3D Printed Pip-Boy, Geiger Counter Not Included” →

Build Your Own Steel Reinforced Storm Shelter

July 1, 2013 by 58 Comments

build-a-steel-reinforced-storm-shelter

The last few years have seen a lot of dangerous storms rip through middle section of the United States. We’re surprised to hear that many residents in that part of the country don’t have basements to take refuge in when in imminent danger. But a resourceful hacker will always be able to find a way to improve their own situation. This example is particularly useful. It’s a steel storm shelter which opens into the garage.

It all starts with a cage made of square tube. With the skeleton fully assembled it is wrapped in steel plate, adding weld joints running nearly the entire length of each of the cage’s ribs. The image at the left shows the steel door frame clamped in position. Check out the finished version on the right after the shelter has been slid into place and bolted to the concrete slab.

The Reddit discussion includes a debate on whether the door should swing in or out. Swinging out means you could be trapped if the opening is blocked by debris. But there may be scientific research that proves this is a better orientation. Either way, we hope the three dead bolts, door latch, and heavy-duty hinges will stand up to the pressure if this is ever used.