FLOSS Weekly Episode 784: I’ll Buy You A Poutine

This week Jonathan Bennett and Dan Lynch talk with François Proulx about Poutine, the Open Source security scanner for build pipeline vulnerabilities. This class of vulnerability isn’t as well known as it should be, and threatens to steal secrets, or even allow for supply chain attacks in FLOSS software.

Poutine does a scan over an organization or individual repository, looking specifically for pipeline issues. It runs on both GitHub and GitLab, with more to come!

Continue reading “FLOSS Weekly Episode 784: I’ll Buy You A Poutine”

Mechanical 7-Segment Display Looks Clean

[Jens] wanted a subscriber counter for his YouTube channel. He could have gone with a simple OLED, LCD, or LED display, but he wanted something more tactile and interesting. So he built a mechanical 7-segment display instead!

Currently, [Jens]’s channel is in the four-digit subscriber range, so he planned to build a four-digit display. He started by searching for existing projects in this space, and came across the designs of [shiura] on Thingiverse. [shiura] had a 3D printed cam-driven 7-segment digit that runs on a single servo motor. Once armed with four of the digits, he hooked them up to a Pi Pico W to drive them all with four servo outputs. The Pico W is responsible for querying the channel subscriber count online, and updating the display in turn.

It’s a neat build, and [Jens] learned some things along the way—like how Super Lube seemed to ruin filament for him. Ultimately, the build came good, and it looks great. We’ve seen some other mechanical 7-segment builds before, too!

Continue reading “Mechanical 7-Segment Display Looks Clean”

Trying To Build A Communications Device With A 1-Pound Laser And A 7805

You can get a red laser diode pretty cheap these days—as cheap as £1 in fact. [Beamer] had purchased one himself, but quickly grew bored with just pointing it at the walls. He decided to figure out if he could use it for some kind of communication, and whipped up a circuit to test it out.

To do the job, he designed a modulator circuit that could drive the laser without damaging it. The build is based around the common 7805 regulator and the venerable 555 timer IC. The 555 is set to pulse at a given rate with the usual array of capacitors and resistors. Its output directly drives the input of a 7805 regulator. It’s set up as a constant current source in order to deliver the correct amount of current to run the laser. The receiver is based around a photodiode, which should prove fairly straightforward.

[Beamer]’s still working on the full setup, but plans to use the laser’s pulses to drive a varying analog meter or something similar. Not every communications method has to send digital data, and it’s good to remember that! Video after the break.

Continue reading “Trying To Build A Communications Device With A 1-Pound Laser And A 7805”

Hackaday Podcast Episode 271: Audio Delay In A Hose, Ribbon Cable Repair, And DIY Hacker Metrology

What did Hackaday Editors Elliot Williams and Al Williams find interesting on Hackaday this week? Well, honestly, all the posts, but they had to pick some to share with you in the podcast below. There’s news about SuperCon 2024, and failing insulin pumps. After a mystery sound, the guys jump into reverbing garden hoses, Z80s, and even ribbon cable repair.

Adaptive tech was big this week, with a braille reader for smartphones and an assistive knife handle. The quick hacks ranged from a typewriter that writes on toast to a professional-looking but homemade ham radio transceiver.

Check out the links below if you want to follow along, and as always, tell us what you think about this episode in the comments!

Download a file chock full of podcast here.

Continue reading “Hackaday Podcast Episode 271: Audio Delay In A Hose, Ribbon Cable Repair, And DIY Hacker Metrology”

FLOSS Weekly Episode 783: Teaching Embedded With The Unphone

This week Jonathan Bennett and Rob Campbell talk with Gareth Coleman and Hamish Cunningham! It’s all about the Unphone, an open source handset sporting an ESP32, color touchscreen, and LoRa radio. It’s open hardware, and used in a 3rd year university course to teach comp sci majors about hardware and embedded development.

Continue reading “FLOSS Weekly Episode 783: Teaching Embedded With The Unphone”

IRCB S73-7 Satellite Found After Going Untracked For 25 Years

When the United States launched the KH-9 Hexagon spy satellite into orbit atop a Titan IIID rocket in 1974, it brought a calibration target along for the ride: the Infra-Red Calibration Balloon (IRCB) S73-7. This 66 cm (26 inch) diameter inflatable satellite was ejected by the KH-9, but failed to inflate into its intended configuration and became yet another piece of space junk. Initially it was being tracked in the 1970s, but vanished until briefly reappearing in the 1990s. Now it’s popped up again, twenty-five years later.

As noted by [Jonathan McDowell] who tripped over S73-7 in recent debris tracking data, it’s quite possible that it had been tracked before, but hidden in the noise as it is not an easy target to track. Since it’s not a big metallic object with a large radar cross-section, it’s among the more difficult signals to reliably pick out of the noise. As can be seen in [Jonathan]’s debris tracking table, this is hardly a unique situation, with many lost (XO) entries. This always raises the exciting question of whether a piece of debris has had its orbit decayed to where it burned up, ended up colliding with other debris/working satellite or simply has gone dark.

For now we know where S73-7 is, and as long as its orbit remains stable we can predict where it’ll be, but it highlights the difficulty of keeping track of the around 20,000 objects in Earth orbit, with disastrous consequences if we get it wrong.

Hackaday Podcast Episode 270: A Cluster Of Microcontrollers, A Rocket Engine From Scratch, And A Look Inside Voyager

Join Hackaday Editors Elliot Williams and Tom Nardi as they get excited over the pocket-sized possibilities of the recently announced 2024 Business Card Challenge, and once again discuss their picks for the most interesting stories and hacks from the last week. There’s cheap microcontrollers in highly parallel applications, a library that can easily unlock the world of Bluetooth input devices in your next project, some gorgeous custom flight simulator buttons that would class up any front panel, and an incredible behind the scenes look at how a New Space company designs a rocket engine from the ground up.

Stick around to hear about the latest 3D printed gadget that all the cool kids are fidgeting around with, a brain-computer interface development board for the Arduino, and a WWII-era lesson on how NOT to use hand tools. Finally, learn how veteran Hackaday writer Dan Maloney might have inadvertently kicked off a community effort to digitize rare documentation for NASA’s Voyager spacecraft.

Check out the links below if you want to follow along, and as always, tell us what you think about this episode in the comments!

Download your very own copy of the podcast right about here.

Continue reading “Hackaday Podcast Episode 270: A Cluster Of Microcontrollers, A Rocket Engine From Scratch, And A Look Inside Voyager”