EEVblog Dissects A Kindle 3

September 3, 2010 by Caleb Kraft 26 Comments

guts!

[Dave] over at the EEVblog did a review of the kindle 3 recently, but never got to the good stuff, the guts. He is now rectifying this with a full video dissection of the eReader. Full of details on how to open it up as well as specifics on the internals, this is a fun video to watch. One thing that caught our attention was the RFID tag on the inside of the case. It is probably for inventory tracking, but we can’t help but have a few tinfoil hat type thoughts. You can watch the video after the break.

Continue reading “EEVblog Dissects A Kindle 3” →

Tube Preamp With A Dazzling Wood Case

August 28, 2010 by Mike Szczys 8 Comments

It’s been a while since we’ve looked in on the world of vacuum tube audio equipment. [Bruce] just finished documenting a tube preamp he built. He actually made a couple of these with slightly different cases but they use the same circuit design. We found his discussion of common errors made when tying into ground quite interesting. It seems that many folks struggle with noise in their circuits because of ground loops. There’s some details about isolating the signal ground from a metal chassis, and also an admonition about not connecting the input or output jacks directly the chassis.

If you like this, don’t miss on of our favorite tube projects, [Bruce’s] Poddwatt.

Adventures In Consumer Electronics Control (CEC)

August 24, 2010 by Mike Szczys 15 Comments

[Valkyrie-MT] was frustrated by the inability to control TrueHD audio volume from his computer. That’s because digital audio passes through the cable to the receiver where the volume adjustments are done. This meant that his RF computer remote was no good because the receiver uses an IR remote. He set out to find a way to get around this and ended up working with the Consumer Electronics Control (CEC) protocol.

The CEC protocol is a 1-wire serial bus built into the HDMI standard. The solution he settled up required one solder connection on the motherboard as well as the internal USB translator module seen above. That translator box, called the RainShadow, is a PIC 18F87J50 controlled board that translates incoming commands from the USB connection and sends them out as CEC hex codes. A bit of code writing and [Valkyrie-MT] is in business. You can see in the video after the break that it’s not just controlling audio, he can now control the entire entertainment center including turning on the TV and setting it to the appropriate input.

Continue reading “Adventures In Consumer Electronics Control (CEC)” →

Giving An IR Transmitter Some Strength

August 22, 2010 by Mike Szczys 17 Comments

[Jkx] was using a Thomson VS360U video transmitter to make a wireless connection between a cable box and his television. The system using an RF remote, but relies on an IR transmitter to communicate between the base station and the cable box. He found the IR module that comes with the device is under-powered and set out to fix the situation. Using a scope he found the pin that drives the IR LED. The board above contains a boost circuit that patches into voltage and ground, using the pin he sniffed out to control the base of a transistor. Now the device has enough power to reliably control the cable box.

Laminar Water Jet Explained

August 22, 2010 by Caleb Kraft 37 Comments

[youtube=http://www.youtube.com/watch?v=Ijn98G0I99E]

[Dave] has put together this laminar water jet, mainly from PVC and drinking straws. There isn’t a project page, but he does go into a little depth explaining how it works. The water enters at the bottom and is slowed down by a series of sponges, then forced through a column of drinking straws. It then pools at the top before being forced through a perfectly smooth and sharp nozzle. We did manage to find this other video, making one for $15 that has a ton of information and links. How long before we see a submission of a complete music synchronized fountain in one of our readers yard?

Cybraphon, Rocks Hard To The Mood Of The Internet

August 13, 2010 by Jakob Griffith 13 Comments

Start off with a beat, wood sticks on cigar boxes will do. Add some chimes as accent, a Farfisa organ or record player for a voice, several other instruments for harmony and dissonance, and you’re still just on the tip of the iceberg for understanding Cybraphon.

Not only is this antique wardrobe completely autonomous, playing music with over 60 robotic instruments, its song are based on the current mood of the internet. You definitely don’t want to miss the video (or pictures) on this one, catch it after the rift.

[Thanks to PsychoNerd91]

Continue reading “Cybraphon, Rocks Hard To The Mood Of The Internet” →

Racing Game Uses A Physical Race Track And Vehicle

August 4, 2010 by Mike Szczys 38 Comments

Racer is a racing video game with a very real element. The player sits in an arcade-style console; wheel, pedals, shifter, and television display. But in what must be an homage to Tron the game taking place is very real. You can see the track above, designed in CAD and cut from cardboard, which is navigated by that little vehicle the gentleman holds in his hand. It’s wireless and broadcasts video back to the control console. What we have here is a homemade drone but for now it’s confined to the gaming grid. Don’t miss the demos after the break. Continue reading “Racing Game Uses A Physical Race Track And Vehicle” →