Roller Coaster Simulator For The Redbull Creation Contest

July 4, 2012 by Brian Benchoff 6 Comments

[Dave] and [Martin], otherwise known as Ballistic Locomotive, sent in their entry for the Redbull creation contest. It’s a roller coaster simulator that can emulate the twists, turns, and drops of a roller coaster in your living room.

The simulator is built around a plywood roller coaster car mounted on a 2 DOF table. With a few first-person roller coaster videos and the speed, roll, and tilt data provided. Ballistic Locomotive had a functioning roller coaster simulator.

Of course, watching a 1st-person shot of a roller coaster just isn’t the same experience without the wind blowing through your hair. To simulate this aspect of a roller coaster ride, so the Ballistic Locomotive team connected a relay to the bullduino and connected a carpet drying fan.

Not only did Ballistic Locomotive build something awesome with their bullduino, they also manage to make a great ride for one of the builder’s son’s birthday party this weekend. You can check out the demo and a few videos after the break.

Continue reading “Roller Coaster Simulator For The Redbull Creation Contest” →

Ask Hackaday: Who Wants To Build A Function Generator?

July 4, 2012 by Brian Benchoff 17 Comments

[tari] sent in a tip about a MAX5214 DAC evaluation board AVNET is giving away this summer. The MAX5214 / MAX5216 is a neat little chip providing a 14 or 16 bit DAC with a serial interface in a tiny 8-pin package. [tari] thinks this eval board could be hacked into a function generator, and we’ve got to agree. Now, who wants to build one?

It’s entirely possible to take the MAX5214 chip and put it in a circuit with a small ARM uC, a display, and a few knobs, but that seems like a waste of time given function generators of this caliber are already available for about $60. It seems the most efficient hack of this dev board will be simply adding an amplifier to this board’s output and possibly programming a better interface than the current LabView software available.

If you want to tinker around with some free hardware and make something useful in the process, have a go at making a function generator out of this dev board. Be sure to send it in when you’re done.

Building A Moat For Your Hackerspace; Alligators, Piranhas Not Included

July 4, 2012 by Brian Benchoff 11 Comments

There has to be something tainting the water supply over at the Louisville Hackerspace LVL1. They’re building a freaking moat in front of their building, ostensibly to keep the black knight and zombies at bay.

After digging a 14-foot deep trench in front of their building – a hazard mitigated by a few steel plates and orange cones generously donated by the Louisville city workers – the members of LVL1 started moving pipes around in preparation for their moat.

Officially, the Louisville city council thinks this project will be a fountain and reflecting pool. City hall seems very friendly; the Louisville chamber of commerce asked about including LVL1 in next year’s Derby tour.

The barely-zombie proof moat build is the latest in a series of builds to improve the security of LVL1. Previous builds included a robotic overlord guarding the building and a robotic arm to cajole members into doing its bidding. Like we said, there’s probably something in the water supply.

Start Thinking 4th Dimensionally With A Time Circuit Tutorial

July 3, 2012 by Brian Benchoff 17 Comments

When [Phil Burgess] showed off a few I2C – controlled seven-segment displays on adafruit’s weekly vlog, the comments immediately turned to the time circuits featured in everyone’s second-favorite time machine, the Back to the Future DeLorean. The time circuits are now active, so now you can easily add a temporal display to your car well before a hover conversion.

[Phil] used these LED displays, conveniently controlled by a four-wire I2C bus. Although the displays are addressable independently, it’s only possible to assign each display to one of 8 I2C addresses. [Phil] figured out a neat way to control the 9 displays of the time circuit with the help of a 74HC138 3-to-8 line decoder.

The case was constructed out of clear acrylic lasercut in adafruit’s shop and spray painted with faux-metal paint. After installing the seven-segment displays, a Teensy, ChronoDot, and a few AA batteries finished up the build.

With any luck, the design files for the laser cut case should be available shortly, so get those I2C displays while they’re still in stock.

Adding A Bomb Bay To A Quadcopter

July 2, 2012 by Brian Benchoff 24 Comments

The Fourth of July is fast approaching, and what better way to celebrate the independence of your country than by blowing up a small piece of it? [Anzel360] decided to take that line of thought to a whole new level by adding a bomb bay to his quadrocopter.

[Anzel360] recently upgraded his transmitter to a Spektrum DX8, giving him two extra channels on his four-channel quadrotor. After adding a small servo to the quad, it was a simple matter of taping a box to the undercarriage and filling it full of fireworks.

The ammo [Anzel] is using is just a handful of Snappin’ Pops – otherwise known as the lamest firework ever created. We won’t hold that against him, though; a remote ignition system for a few Black Cats mounted on a fancy quadrocopter is just asking for trouble. We do recall a throwable cap gun bomb from our youth, though, that would allow for year-round ammo replenishment…

Printing Organs With A 3D Printer

July 2, 2012 by Brian Benchoff 24 Comments

[Jordan Miller], [Christopher Chen], and a whole bunch of other researchers at the department of bioengineering at U Penn have figured out a way to print 3D tissues using a 3D printer. In this case, a RepRap modified to print sugar.

Traditional means of constructing living 3D tissues face a problem – in a living body, there’s a whole bunch of vasculature sending Oxygen and nutrients to the interior cells. In vitro, these nutrients can’t get to the cells in the core of a mass of tissue. [Jordan], [Chris], et al. solved this problem by printing a three-dimensional sugar lattice. After encasing this lattice in a gel embedded with living cells, the sugar can be dissolved and the nutrients pumped through the now hollow capillaries in the gel.

If you have access to Nature, the full text article is available here. There’s also a great video showing off this technique after the break.

Continue reading “Printing Organs With A 3D Printer” →

Getting A Console And Quake II Running On A Raspberry Pi

July 2, 2012 by Brian Benchoff 14 Comments

Those Raspberry Pi boards are flying into the mailboxes of tinkerers all around the globe, so our tip line is currently awash in a deluge of Raspi hacks. Here’s two that came in over the weekend:

First up is [reefab]’s port of Quake II for the Raspberry Pi. The build is based of Yamagi Quake II and is mostly playable. The Quake III port for the Raspberry Pi is old hat, but we’re happy to relive the pulse-pounding action of Quake II any day.

Next up is [Joonas]’ take on getting a serial console up and running with the Raspi. The Raspberry Pi has a UART serial console on its 26-pin header, but you can’t just connect those pins to a serial port. To shift the +/- 12V down to the 3.3 Volts the Raspi can understand, [Joonas] used a MAX3232 – the 3.3 Volt version of everyone’s favorite RS-232 transceiver. With a breadboard and a couple of caps, it’s easy to connect your Raspi to a serial console. Neat.