Catch Neighborhood Speeders With Your Webcam

May 31, 2012 by Mike Szczys 56 Comments

[John] is keeping the neighborhood safe by keeping an eye out for speeders. Well, he’s really keeping a webcam out for speeders. His technique doesn’t use radar or lasers. He’s processing webcam frames in Python to calculate speed.

It comes down to some basic image manipulation. He firsts gathers the images necessary to make the calculations by using a motion-detecting webcam program called YawCam. The images are analyzed to establish which parts have changed between frames; this gets rid of all the stationary objects. Now the frames can be compared to establish the distance in pixels. By calibrating the shot through measurements of the target area, this data can be directly converted into actual distance. It is then compared with the timestamps from each frame to arrive at speed. This can be used for vehicles on the street like we see above, or more whimsical measurements like pet turtle progress.

Robot Arm Provides Haptic Feedback From The Virtual World

May 31, 2012 by Mike Szczys 2 Comments

[Diego] wrote in to let us know about the haptic feedback arm project with which he’s hard at work. He calls it the Vimphin, which is uses the beginning letters from the words: Virtual Manipulator Physical Interface. Instead of a claw, the robot arm has a hand grip that lets you easily move it around. That is unless the virtual model of the arm encounters a dense substance, and then it’s going to be more difficult to move.

The test arm seen above includes several high quality robotic servo motors. You probably know that servo motors have feedback circuits that let them sense their position, and this is what is used to detect when a user moves the arm. This movement is tracked in the virtual 3D environment seen on the screen. In this case, the base of the robot is sitting in a pool of water. When the end of the virtual arm is in open air it’s pretty easy to move. When it dips below the water line the motors are used to increase resistance, simulating movement through a denser substance.

This sounds like a great piece of hardware to have around when the OASIS is finally developed.

Continue reading “Robot Arm Provides Haptic Feedback From The Virtual World” →

ATtiny85 Sketch Flashing Rig

May 31, 2012 by Mike Szczys 9 Comments

We’re happy to see Arduino enthusiasts championing the use of smaller hardware when the need for a full-blown ATmega-based board just isn’t there. [Chris] has been doing just that, using ATtiny85 chips in his projects. But he’s tired of hooking jumper wires to flash the sketches. He finally got around to etching this ATtiny85 programming adapter.

If the project is not pin hungry, an ATtiny85 can run Arduino sketches without the need to port the code. The best news is that the Arduino board you used to prototype the project can be used as the programmer for the standalone chip. Here that’s a Boarduino, and [Chris] laid out a double row of female pin headers for quick plug-in. To the right you can see the DIP socket for the target chip. Although this works perfectly well, we would have liked to also see the inclusion of a 2×3 AVR ISP programming header which could be used with the full range of AT chips.

Hackerspace Intros: Freeside Hackerspace In Atlanta Georgia

May 31, 2012 by Caleb Kraft 14 Comments

When I announced that I would be traveling through some areas of the southeast this summer, [Slade] from Freeside Atlanta emailed me to set up a stop at their hackerspace. I am very happy he did too, because this place was really cool. [Steven Sutton] agreed to walk us through the facility and did a great job of being the tour guide.

Continue reading “Hackerspace Intros: Freeside Hackerspace In Atlanta Georgia” →

All-in-one All Grain Brewing For Your Kitchen Counter

May 31, 2012 by Mike Szczys 10 Comments

All grain brewing is a labor and equipment intensive endeavor, but it produces the highest quality beer compared to partial mash or extract brewing. [Jeff Karpinski] started out with the latter two methods, but as his enthusiasm for the hobby mounted he found himself brewing all-grain batches with just an electric kettle. He developed the system seen above as an easy method of automating the all grain process, and he managed to make it tidy enough to do in the kitchen.

All-grain brewing usually involves five or ten gallon (or more) boils. This type of volume is usually what demands that the brewing process move out of the kitchen. But since [Jeff] is the only beer drinker in the house he limits his sessions to three gallons. This means all of the equipment takes up less room. Here he’s got a five-gallon bucket, cooler, and brew kettle on just one small piece of the counter. In between the kettle and bucket you can see the controller box he built. This is responsible for switching power to the heating element in the brew kettle, and the electric pump in the bucket. The bucket has a permanent counterflow chiller which brings the wort down to a suitable temperature before pitching the yeast. It’s pretty amazing how well contained the liquid is from start to finish!

[Thanks ScottInNH]

Kilonode: How To Test A Huge Xbee Mesh Network

May 31, 2012 by Mike Szczys 11 Comments

So let’s say that you’re a developer on the Xbee team. You need to test the extremes of what the RF radio modules can do when in a large network. But in addition to numerous nodes, you also need to test the effects of distance on the radios. Since it’s not reasonable to distribute hundreds of the devices (each with their own power source) throughout town, you build a test setup like the 1 kilonode Xbee rig which the project manager, [Jared Hofhiens] is showing off.

He’s holding one blade from the rack-mounted system. Each of those squares is an Xbee module, there’s 32 etched onto the board. On the edge furthest from him there are a set of connectors which mate with the rack connectors, hooking the blade up to a set of terminal servers. These servers allow developers to ssh into individual modules. On the near side of the blade there’s a set of attenuation adjustment circuits. They allow adjustments of 0-40 dB of attenuation in 10 dB increments to adjust how strong the RF signals are, simulating distance between modules.

Thirty-two of these cards are mounted in the three racks seen above to make up the 1024 module node. We really appreciate this look behind the scenes and think you’ll enjoy the video tour after the break. If it leaves you wanting more check out how one company builds cloud storage. Continue reading “Kilonode: How To Test A Huge Xbee Mesh Network” →

3d Printing, The New Frontier Of Piracy?

May 31, 2012 by Caleb Kraft 89 Comments

We’ve all heard the countless arguments about piracy in digital media. However, it appears that 3d printing or other rapid prototyping systems are bringing legal issues to a more physical world. The story goes like this: [Thomas] bought a 3d printer. He’s a big fan of warhammer figurines. He spends tons of time creating some custom warhammer figures, and uploads them to thingaverse. Games Workshop, the owners of Warhammer, unleashed the lawyers and had the items removed.

There are so many angles to this story, the mind boggles. If I were an artist, and someone else was uploading copies of my work, essentially stopping my revenue, it would suck. Then again, if I were lucky enough to have a fanatical fan base that spread the love for my product with excitement and zeal, I might want to encourage them. Neither of those thoughts however, cover the legal issue at the base here. We don’t have an answer for you. Sorry. You’ll probably be seeing this issue pop up more and more often in the future.

We encourage you to make our logo. Though we haven’t bothered to ask our lawyers.