Halloween Hacks: A Light And Music Show Fit For [Jack Skellington]

October 28, 2011 by Mike Nathan 4 Comments

Halloween Hacks Banner

singing_pumpkin_halloween_show

[Greg] was looking for something to build using his recently acquired Arduino, and with Halloween approaching, he thought a cool light display would make a great project. He browsed around online and found this tutorial that shows how to build a chorus of singing pumpkins controlled by a computer’s parallel port. Since he didn’t have any computers with a parallel port kicking around anymore, he decided to try his hand at recreating it with an Arduino.

[Greg] gathered eight light up Jack-o-Lanterns, along with a handful of relays and other miscellaneous components. He wired up the relays to trigger each individual pumpkin’s built in light when switched by the Arduino. He sat down and carefully listened through “This is Halloween” from The Nightmare Before Christmas, choreographing each of the pumpkins to take on the voice of one of the movie’s characters.

When the show begins, the display transforms from a group of unassuming pumpkins with candles a-flicker to a chorus of ghouls extolling the virtues of Halloween.

It really is fun to watch, so be sure to check out the video below. If you’re looking to throw together a quick display before the big day rolls around, [Greg’s] source code and diagrams should get you headed in the right direction.

Continue reading “Halloween Hacks: A Light And Music Show Fit For [Jack Skellington]” →

Adding A Compact Flash Reader To A Korg Triton

October 23, 2011 by Mike Szczys 22 Comments

[Roberto Barrios] has a Korg Triton sampling keyboard which he enjoys very much, but has grown tired of using media of yesteryear to store his work. He had the option of floppy disk or Jazz drive and for a time he was using a floppy-to-USB emulator, but the keyboard still insisted on a 1.44 Mb storage limit using that method. He decided to crack open the case and add his own CF reader.

It should be noted that this hack could have been avoided by using the 25-pin connector on the back of the keyboard. He didn’t want to have external hardware, which is understandable if you’re gigging–it’s just more equipment to keep track of. His solution uses the floppy disk drive opening to mount the card reader. His electrical connections are made with a ribbon cable. He cut off one end, and soldered the individual wires to the contacts on the motherboard. The reader is seen as a SCSI drive by the Korg firmware thanks to a SCSI-to-IDE adapter, so the storage limitation is based quite fittingly on the size of the CF card used.

Look at that cable management. You’d think it came straight from the factory like this!

7400 Drum Machine Is A Delight

October 22, 2011 by Mike Szczys 24 Comments

[74hc595] just finished his entry in the 7400 logic contest. It’s a drum machine built entirely from 7400-series logic chips. He hasn’t quite reached full completion of the project yet. The hardware works just fine, and he’s built a foam core face plate with many more controls than you see here but much of the circuit is still on a breadboard at this point and only two of the channels have been complete thus far.

Jump to the video clip after the break to get the details of how the system works and to hear it in action. This demonstration is one of the best we’ve seen for a synthesizer project as he actually talks about what each control does, and how that is accomplished with the hardware. We’re not going to go into detail about the circuitry he’s designed. As we said before, it uses 7400 logic but also sources a 555 timer to keep the beat. The page linked above has a PDF of the schematic available and you could really lose a lot of time studying how he did this. We might even try to build it in a simulator to see what we can learn.

Continue reading “7400 Drum Machine Is A Delight” →

Hydrocrystallophone Probably Won’t Make You Insane

October 21, 2011 by Brian Benchoff 27 Comments

[Fish] is really proud of his newest creation, the Hydrocrystallophone. This new instrument reminds us of an even more steampunk version of [Benny Franklin]’s glass armonica – an instrument that reportedly plunged the player into a, “dark and melancholy mood.”

The build is based around a 1920s hand-cranked phonograph motor. The phonograph motor spins a wine glass filled with water. The water level (and thus tone produced by the wine glass) is varied by a brass tube inside the glass connected to a hydraulic cylinder. Pushing and pushing on the handle of the hydraulic cylinder causes the water level in the glass to change.

We’ve all seen wine glass music before, but this is the first time we’ve seen it with just one glass. [Fish] is working on modifying the phonograph’s governor to get rid of the effects of 78 RPM on the water. He hasn’t quite mastered his new musical invention yet, but we can’t wait to see what [Fish] is able to play with some practice.

In case you’re keeping track of the musical instruments featured on Hack A Day that fall into the “why didn’t I think of that” bin, The Hydrocrystallophone would be the second such instrument in as many months. It’s a very simple but really ingenious device. Check out the video of the Hydrocrystallophone after the break.

Continue reading “Hydrocrystallophone Probably Won’t Make You Insane” →

Cheap Acoustic Panel DIY

October 21, 2011 by Jesse Congdon 37 Comments

[Eric Wolfram] wrote in to let us know about a simple and cheap acoustic panel DIY he put together. When installing a home theater acoustics are often neglected (especially if you spend so much on the TV you cannot afford any furniture for the room) resulting in reduced listening quality and poor spacial sound imaging from your surround system (also responsible for the furniture problem). The addition of sound absorbing panels helps control the acoustics of the room and may even class up the place a bit. These are also come in handy for home studio usage where a low level of reverberation is preferred.

The panels are relatively simple to produce on a budget, just a sheet of 2″ thick dense fiberglass board glued into a wooden frame and covered in a sound-transparent fabric. [Eric] goes into a lot of the material selection process to help you along your way. The best part about the project (aside from its obvious utility) is that all of the materials can be found cheaply at your average home improvement store, with the exception of the fabric. [Eric] mentions that you can substitute colored burlap if need be. Once the panel is assembled and glued it just has to be hung on the wall of your choice like a large heavy picture frame. This could certainly help the acoustics and reduce some slap-back echo in your warehouse/shop. We might have to try this one over the weekend.

Thanks [Eric]!

Analog IPhone Amplifier Made From Recycled Trumpets

October 7, 2011 by Mike Nathan 14 Comments

analog_telephonographer

It’s no secret that the audio quality of the iPhone’s built-in speakers isn’t exactly what you would consider to be hi-fi. Sound quality aside, there are plenty of times where even the volume doesn’t do the music justice. While you can always go out and buy a fancy dock to amplify your iGadget’s sound, artist [Christopher Locke] has a different take on the subject.

For a while now, he has been constructing what he calls “Analog Tele-Phonographers”, metal sculptures that can be used to amplify a mobile phone’s audio. Built out of steel and old trumpets, his audio sculptures require no electricity, instead utilizing the same amplification technology as the original phonographs.

While the Tele-Phonographers won’t make your iPhone sound like a high quality tube amp, they do undoubtedly increase the phone’s volume and they are nice to look at. We can certainly get behind this sort of recycling/reuse of old items.

Continue reading to see a quick video of his Analog Tele-Phonographer in action.

[Thanks, Chris]

Continue reading “Analog IPhone Amplifier Made From Recycled Trumpets” →

Playing Dubstep On Real Instruments

October 7, 2011 by Brian Benchoff 52 Comments

When we first saw the live cover of Skrillex Scary Monsters And Nice Sprites by the band Pinn Panelle, we had to know how a band is able to play live dubstep on real instruments. We emailed the band and they spilled the beans on how to process the hell out of an instrument in a live environment.

First up is the bassist, [Nathan Navarro]. He wears a Source Audio Hot Hand on his right thumb. This little box is a two-axis accelerometer that communicates with his pedal board using RF frequencies. With the Hot Hand, he has control over two parameters on Hot Hand Pedals. The envelope effect is awesome, but it’s worth noting that [Nathan] is sponsored by Source Audio. We’re thinking it would be relatively easy to cram a Wii MotionPlus and microcontroller into a wristband. Tied to a computer and MIDI interface, the homebrew solution would do the same thing.

[Derek Song] is the guitarist and he’s used multieffects for most of his musical life He has a small Bluetooth keyboard and touchpad mounted to the front of his guitar that controls just about everything on his pedal board. The Bluetooth controller sends commands to [Derek]’s computer that outputs MIDI CC messages to his pedal board.

In a studio, Pinn Panelle’s cover would be impressive. The fact that it’s being played live opens up a number of doors as to what a band can do in real-time. If you’ve got a pedal board or electronic music build, send it into the tip line. Also, check out the videos after the break for a better demo of [Derek]’s Bluetooth setup.

Continue reading “Playing Dubstep On Real Instruments” →