Twitter Radio

December 12, 2012 by Mike Szczys 12 Comments

This anthropomorphized wood bowl will read Tweets out loud. It was built by [William Lindmeier] as part of his graduate work in the Interactive Telecommunications Program (ITP) at New York University. View the clip after the break to see and hear a list from his Twitter feed read in rather pleasant text-to-speech voices.

The electronics involved are rather convoluted. Inside the upturned bowl you’ll find both an Arduino and a Raspberry Pi. But that’s not the only thing that goes into this. The best sounding text-to-speech program [William] could find was for OSX, so there is a remote computer involved as well. But we think what makes this special is the concept and execution, not the level of hardware inefficiency.

The knob to the left sets the volume and is also responsible for powering down the device. The knob of the right lets you select from various Twitter lists. Each turn of the knob is responded to with a different LED color in the nose and a spoken menu label. You can get a quick overview of the project from this summary post.

Continue reading “Twitter Radio” →

Garage Door Opener Using Siri And Raspberry Pi

December 11, 2012 by Mike Szczys 27 Comments

Screenshot from 2012-12-11 09:54:36

[DarkTherapy] wrote in to tell us about his garage door opener that works with Siri and a Raspberry Pi. It’s pretty hard to find a picture that tells the story of the hack, but here you can see the PCB inside the housing of the garage door opener. He patched the grey wires into the terminal block. On the other end they connect to a relay which makes the connection.

On the control side of that mechanical relay is a Raspberry Pi board. This seems like overkill but remember the low cost of the RPi and the ability to communicate over a network thanks to the WiFi dongle it uses. We think it’s less outrageous than strapping an Android phone to the opener. To make the RPi work with Siri he chose the SiriProxy package. We’ve seen this software before but don’t remember it being used with the Raspberry Pi.

There is certainly room to extend the functionality of a system like this one. It would be trivial to add a combination lock like this one we build using an AVR chip. It would also be nice to see a sensor used to confirm the door is closed. Even if you don’t need to control your garage this is a great reference project to get the RPi to take commands from your iOS devices.

Continue reading “Garage Door Opener Using Siri And Raspberry Pi” →

Standalone Air Quality Monitor Based Around Raspberry Pi

December 11, 2012 by Mike Szczys 4 Comments

rpi-air-quality-monitor

You can have a lot of fun tinkering with the Raspberry Pi. But in addition to the low-cost hobby potential it is actually a great choice for serious data harvesting. This air quality monitor is a great example of that. The standalone package can be taped, screwed, bolted, or bungeed at the target location with a minimum of effort and will immediately start generating sample data.

The enclosure is a weather proof electrical box. The RPi board is easy to spot mounted to the base of the case. On the lid there is an 8 Ah battery meant to top off an iPhone. It works perfectly as it provides a USB port and enough current to operate the Pi. On top of that battery is a 3G modem used to access the data remotely — although it can log to the SD card for collection at a later time if you’d rather not mess with a cell network.

Look closely at the GPIO header and you’ll notice that an ADC add-on board has been plugged in. This is used to take the readings from the gas sensor which is monitoring for air pollutants in Paris.

Transmit FM Using Raspberry Pi And No Additional Hardware

December 10, 2012 by Mike Szczys 75 Comments

Now here’s a project that actually hacks the Rapsberry Pi rather than just using it as an embedded computer. [Londons Explorer] figured out how to turn the RPi into an FM transmitter. For now it’s done entirely in the user space, but we’re sure it could be improved if someone wanted to drill down further into the hardware. For those wanting to give it a try he’s rolled everything into a simple python package.

The technique requires nothing additional except a 20cm wire to serve as an antenna. The trick is to map GPIO pin number 4 to a position in memory. The clock generator is then used to toggle this pin at 100 MHz, which is the frequency to which your radio should be tuned. A fractional divider adjusts the frequency based on the sound file being transmitted.

The proof of concept for this was able to reliably transmit at a distance of about fifty meters through several walls. The problem is that this technique is limited in the amount of data which can be sent. Right now it’s only about 6-bit audio. But descending deeper through the abstraction layers to put DMA (Direct Memory Access) to use may be able to improve upon this.

[Thanks Owen via Reddit]

Injecting Power Into A WiFi Dongle For The Raspberry Pi

November 27, 2012 by Mike Szczys 20 Comments

So the Raspberry Pi sometimes doesn’t have the juice needed to run power-hungry USB dongles. The most common issue is with WiFi adapters. The solution has long been to use a powered USB hub, but [Mike Worth] didn’t want to take up that much extra space. The solution he worked out injects power directly into the dongle itself.

The red and white wires coming out of the side provide the 5V source. This is coming from the same USB mains power adapter that supplies the RPi board itself. To connect the wires to the dongle he made an adapter out of some strip board and the shielding from the dongle. The end of the strip board pokes out of the shielding far enough for him to solder on some wire, which is then soldered to the traces on the dongle’s PCB.

You can just plug this in and get down to business. But while he was at it [Mike] added an improvised antenna for better reception. It’s the same type of hack we saw him use for a Bluetooth dongle in this links post.

Android VOIP Phone And Raspberry Pi Mate For An Intriguing PBX Setup

November 26, 2012 by Mike Szczys 5 Comments

[Ward Mundy] has found something great by combining a GXP-2200 phone with Raspberry Pi to create a private branch exchange. So the idea behind a PBX setup is kind of like a company intranet. All of the phones in the system are assigned an extension number and have access to the internal system functions like voice mail, and sharing phone lines to the outside world. We’ve talked about using an RPi as a PBX before, but the high-tech phone he’s using this time around pulls everything together remarkably well.

The GXP-2200 is available for under $200. It runs Android and has a full color touch screen pictured above. It is marketed as a multimedia phone and indeed it brings Skype and Google Voice to the party. But it also offers six SIP lines. The hardware even seems to be planned for this type of use as the phone offers a second Ethernet port to which the RPi board can be connected. In this example [Ward] simply screws the RPi to the phone’s plastic stand and connects the two using a six-inch cable. From there the PBX can be configured with the phone’s browser. How’s that for slick?

Raspberry Pi Reaches Critical Mass As XBMC Hardware

November 19, 2012 by Mike Szczys 96 Comments

For years I’ve been dreaming of a streaming media device that could just be stuck to the back of a television. Since XBMC has been far and away my favorite set-top box software, I’ve closely monitored hardware developments that can run that package. Now I think it’s time to declare that the Raspberry Pi has achieved the base specifications to be branded the XBMC device that rules them all.

There are a huge range of opinions on this topic, but please hear me out after the break to see what has brought me to this conclusion.

Continue reading “Raspberry Pi Reaches Critical Mass As XBMC Hardware” →