The Most Portable GameCube Ever

May 22, 2012 by 13 Comments

Here’s the smallest GameCube we’ve seen, straight from the fruitful workbench of [lyberty5] over on the ModRetro forums. Even though we’ve seen disc-less GameCubes before, [lyberty5] puts this project together so well it wouldn’t look out-of-place in the Nintendo product lineup.

Unlike most of the other portable GameCubes we’ve seen, [lyberty5]’s build doesn’t have a disk drive. The games are loaded off an SD card with the help of a Wiikey Fusion, a small FPGA’d device that replaces the CD drive in GameCubes and Wiis with an SD card.

The enclosure was constructed out of vacuum formed plastic with the always popular ‘dremeling and bondoing a controller for proper button placement’ method. Inside the enclosure is the hacked up GameCube, a 3.5 inch screen capable of displaying NTSC video at 640×480 resolution and enough battery power to get two or three hours of playtime from a single charge.

After the break you can check out [lyberty5] fast-paced demo video that really sets the bar for portablized console presentation.

Continue reading “The Most Portable GameCube Ever” →

Shocking Use Of Ice Cube Trays

April 16, 2012 by 13 Comments

Looks like ice-cube trays are once again proving their versatility as this one is serving as the vessel for a home made lead-acid battery. With a collection of uniformly sized non-conductive containers, it makes the perfect base for a set of small cells. This project is the culmination of a Hackerspace class about batteries, and was put together to turn theoretical knowledge into a hands-on lab.

This is a captured image from the low-quality video found after the break. [Carpespasm] describes the setup; the black pieces are lead plates which are bent into a U-shape to straddle two ice-cube compartments. The each end of the plate is dipping into the acid to make the connection. Once assembled the battery was connected to a charger for about two hours. It puts out 8.5V and is tested by powering an LED cube. This works for just a short period and really drives home the lesson that battery concepts are easy to understand, but reliable battery technology is a bit harder to achieve.

Continue reading “Shocking Use Of Ice Cube Trays” →

The Best LED Cube Build We’ve Seen

April 6, 2012 by 28 Comments

[Nick] wrote in telling us about the LED cube he built over the course of six months. He calls LED cubes ‘done to death,’ but [Nick] might be too humble. His 8x8x8 RGB LED cube is the best we’ve ever seen.

To start his build, [Nick] built a simple 4x4x4 cube as a proof of concept. The baby cube worked but the fabrication process got him thinking. Instead of building his monster LED cube in layers from the bottom up, he would need to build columns from left to right. After the construction of a jig, soldering eight panels of 64 LEDs, and buying a new soldering iron tip, [Nick] had a beautiful assembled LED cube. The only thing missing was the electronics.

Most of the LED cubes we’ve seen use the TLC5940 LED driver for hardware PWM, [Nick] decided to go with the simpler but more familiar STP16 chip. After hooking up his huge LED driver board up to a chipKIT Uno, the 80 hours of programming began.

In the end, [Nick] built the best LED cube we’ve seen (even though it isn’t the largest) and put together one of the best build logs in recent memory. Because no LED cube build is complete with out a video there’s an awesome demo after the break.

Continue reading “The Best LED Cube Build We’ve Seen” →

Minimalist RGB LED Cube Has A Very Short BoM

January 7, 2012 by 55 Comments

charlieplexed-led-cube

[Asher Glick] wrote in to share a project he has been working on with his friend [Kevin Baker], a 4x4x4 RGB LED cube. The pair are students at Rensselaer Polytechnic Institute and also members of the newly-formed Embedded Hardware Club on campus. As their first collaborative project, they decided to take on the ubiquitous LED cube, trimming down the component count to nothing more than 64 LEDs, a protoboard, some wire, and a single Arduino.

Many cubes we have seen use shift registers or decade counters to account for all the I/O required to drive so many LEDs. Their version of the cube has none of these extra components, solely relying on 16 of the Arduino’s I/O pins for control instead. You might notice something a bit different about the structure of their cube as well. Rather than using a grid of LEDs like we see in most Charlieplexed cubes, they constructed theirs using 16 LED “spires”, tucking the additional wiring underneath the board.

The result looks great, as you can see in the videos below. The cube looks pretty easy to build, and with a cost around $60 it is a reasonably cheap project as well.

Nice job, we look forward to seeing all sorts of fun projects from the Embedded Hardware Club in the future!

Continue reading “Minimalist RGB LED Cube Has A Very Short BoM” →

LED Cube Is A Little Bit Of Kit, A Lot Of Point-to-point Soldering

January 5, 2012 by 4 Comments

[Craig Lindley] recently finished building his own RGB LED cube project. It’s made up of four layers of 4×4 LED grids, but you may notice that the framework that supports the structure is not the usual ratsnet of wires we’ve come to expect. They’re actually long, thin circuit boards. [Craig] grabbed the Rainbow Cube kit sold by Seeed Studio for this project. But instead of pairing it with their Rainbowduino driver, he built his own to give him more options on how to control the blinky lights.

He’s using an Arduino Uno to control the display, choosing TLC5940 driver chips to safely provide the juice necessary to light up the grid. These drivers also offer 12-bit pulse-width modulation for easy color mixing. Driving the LEDs directly would have taken a large number of these expensive chips (over $4 a piece), but if multiplexed the design only calls for two of them.

Check out a video of the finished cube reacting to music thanks to the microphone and amplifier circuit [Craig] build into the driver board.

Continue reading “LED Cube Is A Little Bit Of Kit, A Lot Of Point-to-point Soldering” →

Flowerboard LED Cube

December 21, 2011 by 6 Comments

Here’s a neat 4x4x4 LED cube made with an ElecFreaks Flower Protoboard.

A few days ago, we posted a neat new prototyping board made specifically for SMD work. Instead of the usual ‘holes-with-circles’ protoboard layout, the ElecFreaks team decided to go with a flower-shaped pad. This makes it especially easy to deal with SMD components when building whatever. To demonstrate their new protoboard, ElecFreaks built an awesome-looking 4^3 LED cube. Just look at those solder traces.

The LED cube itself is nothing we haven’t seen before, but the construction of this thing is amazing. The entire build is on the Arduino Mega Flower shield, meaning there are no wires at all. Everything, from the resistors to the transistors, is an SMD component. The only problem now is bending and soldering all those LED leads.

This Flower Protoboard is starting to look more and more interesting; check it out in action after the break.

Continue reading “Flowerboard LED Cube” →

This Cube Of Playroom Drawers Is Quite Puzzling

October 11, 2011 by 18 Comments

If you’re looking for a piece of custom furniture to anchor your child’s playroom, this Rubik’s cube chest of drawers is just the thing. [Makendo] went the extra couple of miles on the project, building the entire thing from scratch and adding one clever feature after another to make it something special.

It’s made up of three plywood boxes, open on one side to accept a plywood drawer. The drawers were carefully fitted so that it is difficult to see which side is actually the drawer face. [Makendo] even routed a hash-mark of grooves into each face of the cube to make it look like the seams that make up the 9×9 grid of colored squares. Speaking of those colors, the “stickers” themselves are made of 1/4″ plywood and are not permanently affixed. Each is held on with a magnet plus a pair of dowels to keep it from spinning. This way you can rearrange the colors as often as you please.

Each layer of the cube spins thanks to some lazy susan bearings. [Makendo] didn’t want to add too much distance between the different modules so he routed out each side to fit the circular hardware. As a final touch, the drawers themselves can be locked in place using a dowel underneath one of the colored squares. We’ve embedded a video of the cube at play after the break.

Continue reading “This Cube Of Playroom Drawers Is Quite Puzzling” →