Repairing A Junked Signal Generator

October 15, 2012 by Mike Szczys 21 Comments

We must be walking past the wrong dumpsters because we certainly haven’t encountered equipment like this just waiting to be salvaged. [Shahriar] found an HP 8648C Synthesized Signal Generator while he was ‘dumpster diving’ and set out to fix the malfunctioning lab equipment. He posted a 1-hour video on the project, which you can find embedded after the break. The actual fix happens in the first half, the rest of the video is spent testing the resurrected device.

The back corner of the case has been dented, which may be the reason this has been thrown out. When it is first powered it emits an unpleasant screeching noise and the user interface doesn’t do anything. [Shahriar] says he recognizes the sound as a malfunctioning switch-mode power supply. Sure enough, when disconnected from the main board it still makes the noise. It turns out there’s a huge electrolytic capacitor the size of a stack of poker chips which has come loose from the PSU board. When it’s resoldered the device fires up as expected.

Now how are we going to find a digital capture oscilloscope that just needs to have its PSU reassembled?

Continue reading “Repairing A Junked Signal Generator” →

Oscilloscope VFD Repair Like Doing Brain Surgery On Yourself

October 9, 2012 by Mike Szczys 11 Comments

[Jerry Pommer] has an old Tektronix 2236 that is having some issues. Just to the right of the top corner of the screen is a VFD display that is used to show various numerical measurements. Unfortunately this has stopped working, so he made the oscilloscope probe itself in order to trouble-shoot the situation.

The entire repair process was filmed and you can see the 42-minute job embedded after the break. There’s a lot of stuff crammed inside that oscilloscope, and we see a tour of it all at the beginning of the video. Once [Jerry] gets down to business he traces the problem to a JK Flip-Flop used to feed the display. The output appears correct at first, but the clock signal is not functioning as expected. His solution is to use an MSP430 chip to replace the Flip-Flop functions.

The confidence to try this repair was sparked by [Todd Harrington’s] car-stereo VFD repair video.

Continue reading “Oscilloscope VFD Repair Like Doing Brain Surgery On Yourself” →

Repairing A VFD Driver On A Car Stereo

September 24, 2012 by Mike Szczys 29 Comments

We love seeing repairs and always marvel at the ability to track down the problem. [Todd] seems to have a knack for this. He was met with a lot of adversity when trying to get the Vacuum Fluorescent Display working on his car stereo. A lot of persistence, and a little bit of taking the easier way out let him accomplish his goal.

The head unit is out of his 1994 Jeep. He knew the radio functionality still worked, but the display was completely dark. After getting it out of the dashboard he connected it to a bench supply and started probing around. He established that the data lines were still working by setting the radio to auto scan mode and testing with a multimeter. When he went to measure the cathode pins he didn’t get any reading. It seems the driver which supplies that signal is burnt out.

One easy fix would be to replace the parts from a scavenged unit. [Todd] hit the junkyard and picked up one from a Jeep that was just one model year apart from his. Alas, they weren’t exactly the same, and although he swapped out a chip (using a neat heated solder sucker) it didn’t work. In the end he simply dropped in a power resistor to use the 12V rail as a 1V at 0.1A source for the filament.

You can see his repair extravaganza in the video after the break. If you’re looking for tips on scavenging these types of displays check out this post.

Continue reading “Repairing A VFD Driver On A Car Stereo” →

How To Repair A Ribbon Cable Connection On Consumer Electronics

September 20, 2012 by Mike Szczys 34 Comments

It’s not uncommon in cheaper devices to find a ribbon cable soldered directly to the circuit board like the one pictured above. Using a connector would have been a much more resilient approach, but adding parts adds cost. If you take a close look you’ll see things aren’t looking so great anymore. [Chaotic and Random] pulled this board out of his VW Camper Van. Rather than buy an expensive replacement part, he shows us how to repair a soldered ribbon wire connection.

This repair is rather invasive and he suggests trying some hot-air rework (possibly using a heat gun) to fix up any misbehaving connections. But if that has failed it’s time for the knife. The first step is to cut the ribbon so that the LCD can be removed from the board. From there he peels the remaining scrap off ribbon of the pads. This makes us cringe as it could lift traces from the PCB, but he was gentle enough to avoid it. Now comes the time to start reassembling. After thoroughly cleaning the pads the ribbon is cut straight and resoldered. The trick is to flow the solder without melting the ribbon. He uses tin foil to cover the tip and cools it on a moist sponge just before reflowing solder.

It sounds like more art than science. But when the only alternative is to spend hundreds on a new part it may be worth a try.

[Quinn] Resurrects An Amplifier That Experienced Death-by-capacitor

September 12, 2012 by Mike Szczys 28 Comments

[Quinn Dunki] is adding wireless audio to all of the rooms in her home. She’s going with Airplay, snatching up used or refurbished Airport Express units because of their ability to work with both her existing WiFi and the Airplay protocol. The last piece in the puzzle is to get an Amp and she chose the small unit seen above. The problem is that it was dead on arrival and she couldn’t get the company to respond to her issue. So she cracked it open and fixed it right up.

The offenders are the three electrolytic capacitors at the top of the picture. She took some close-up images of each and you can’t miss the fact that they’re blown out. These are often among the higher price-per-unit parts and manufactures try to pinch the penny as much as possible. Add to it the heat in a small enclosure like this one and you’ve got a failure. [Quinn] dug through her junk bin but the size of the replacement had to be a perfect match so she ended up putting in a parts order. The new caps fit and work perfectly as you can hear in the clip after the break.

Continue reading “[Quinn] Resurrects An Amplifier That Experienced Death-by-capacitor” →

Send Your Nexus 7 Back… To Tighten One Screw?

August 10, 2012 by Mike Szczys 12 Comments

It seems that some of the Nexus 7 models have an assembly issue that makes the bezel uneven with the screen. It’s just in one spot but your shiny new toy shouldn’t have this kind of problem. Of course it comes as no surprise that Google wants you to send it back for service. What is a surprise is that the fix involves tightening just one screw. Now we can’t stand for shipping something round trip when it comes to this low-skill fix. Luckily neither can [Baddspella]. He shows us just how easy it is to repair the Nexus 7 yourself.

The only tools you need are a guitar pick (or other thin plastic prying device) and a very small Phillips screwdriver. Starting at the top of the tablet he uses the plastic pick to pry off the back of the case. This exposes the screws which hold the bezel in place. Find the loose one, and give the screwdriver a turn. Now just snap the back cover in place and you’re done. We’ve embedded the video after the break for your convenience.

It’s super simple…. so don’t be afraid to crack that thing open.

Continue reading “Send Your Nexus 7 Back… To Tighten One Screw?” →

Reworking The Electronics For Better Computer Speaker Audio

July 31, 2012 by Mike Szczys 23 Comments

[Michael Chen] liked the sound he was getting out of these Corsair SP2200 computer speakers, with one big exception. They were giving off some unpleasant crackling sounds. He figured this might be as easy as replacing a faulty potentiometer, but soon found out the fix was going to be more complicated than that. All said and done he ended up reworking the design of the speakers’ amplifier board.

The hardest part was identifying the problem. Once he had cracked open the case he found the volume potentiometer was working correctly by testing it with a multimeter. Next he inspected the board for bad solder joints but didn’t really find any. The breakthrough came when he realized that the crackling was also happening when he used headphones. With that discovery he started making a few more observations and realized that the crackling didn’t happen when the volume knob was all the way up or all the way down. There was an impedance issue between that potentiometer and the amplifier circuit. He rerouted the signal flow on the board to use the headphone amp as a filter and it fixed the problem. Fittingly, he’s entered this project into the Instructables Fix & Improve contest.