Cheap Ikea Camera Boom Ensures Shake-free Video

October 12, 2011 by Mike Nathan 19 Comments

ikea_webcam_jig

[Chris] recently got himself a nice web cam for documenting his Makerbot builds, and much like [Dino], he was looking for a way to get a bird’s-eye view of the action while keeping the camera nice and steady. While [Dino] ventured off to the hardware store, [Chris] tried a few different options that included tape, before heading off to Ikea to see what he could find.

$9 and a few Swedish meatballs later, he was on his way home with a “TERTIAL Work Lamp” that can be mounted on virtually any desk-like surface. He had to remove most of the web cam’s useless mounting hardware, doing the same with the lamp’s light fixture. He put together a small bracket in Google Sketchup, which he then printed out using his Makerbot.

It fit perfectly, and now he can get steady video of his Makerbot prints every single time.

Sweet Octocopter Takes The RED Epic To New Heights

October 12, 2011 by Mike Nathan 25 Comments

red_epic_octocopter

So you’ve got a $40k+ RED Epic video camera and you need to get it from all the way down here to all the way up there. Sure, you could rent an expensive crane and take your shots from above that way, but why bother with that when you can fly instead?

German video effects company OMStudios decided that it was up to the task of finding a crane alternative, so they built a crazy octocopter drone to get the camera up to where they needed it. Figuring that if four rotors is good eight is even better, the group’s octocopter lifts the camera to heights of up to 150 meters, which is pretty impressive considering the weight of its payload.

While we might be a little hesitant to trust such an expensive camera to a glorified RC helicopter, it actually looks pretty solid from the video. Besides, we’re pretty sure these guys know what they are doing since they have a RED camera in the first place.

[via Engadget]

Continue reading “Sweet Octocopter Takes The RED Epic To New Heights” →

Garage Door Monitoring And Control Using A Dedicated Android Phone

October 11, 2011 by Mike Szczys 29 Comments

[Sean] happened to have an extra Android phone sitting around and wanted to see what type of home automation he could use it for. One simple hardware modification, and some apps from the Android Market let him monitor and control his garage door remotely.

The hardware modification is a hack we’ve already looked at. The BTmate uses a Bluetooth headset with an added transistor to short the connections on your garage door opener. The only issue is that you need to be within range for the Bluetooth to work. [Sean] adds a layer of abstraction by using two Android phones. One is permanently mounted in the garage and handles the Bluetooth connectivity, while the other uses VNC to tunnel in anywhere he has an Internet connection.

But why stop there? He knew that this one feature was overkill, and added a second which the phone was perfect for. Since it has its own camera, he used the tinyCam app to create a webcam server. This even allows him to turn the LED on and off for a better view in dim light conditions. See [Sean’s] demonstration after the break.

Overkill? Maybe, but if you’ve got a phone with a broken LCD, this might be just the thing to give it a new purpose.

Continue reading “Garage Door Monitoring And Control Using A Dedicated Android Phone” →

Send A Satellite Into Space For $300

October 11, 2011 by Brian Benchoff 63 Comments

There’s a new Kickstarter campaign that promises to launch a personalized satellite into orbit for 300 bones.

The KickSat project is headed by [Zac Manchester], [Mason Peck], [Justin Atchison] and a few more contributors hailing from Cornell University. Their goal is to launch a CubeSat filled with hundreds of postage stamp-sized satellites and release these ‘Sprites’ into low Earth orbit.

The Sprite concept has been in development for a while now and has been featured on IEEE Spectrum. The tiny satellites are simple PCBs with a microcontroller and a radio powered by solar cells and capacitors. The first version of the Sprite is designed to beam down a few bytes of data – just a unique identifier and a Kickstarter backer’s name. Future versions will undoubtedly include more advanced sensors such as cameras, thermometers, and very tiny particle detectors.

The KickSat team will use the funding from the Kickstarter campaign to test and integrate the systems. The team hopes to hitch a ride on one of NASAs many CubeSat launches, but if they get funding from 400 people, they’ll get to fly on a commercial launch by early 2013.

We were wondering about the amazing amount of space junk this KickSat/Sprite build will produce, but the team says not to worry: The Sprites fly in a pretty low orbit and will reenter the atmosphere a few weeks after being deployed. Not bad, considering Sputnik orbited for only 3 months.

Simple Hack Reuses An Air Freshener PIR Sensor

October 11, 2011 by Mike Nathan 5 Comments

pir_sensor_room_greeter

A year ago [Lochie] bought an Airwick automatic air freshener, and while he thought it was a cool gadget, the freshening spray and the novelty ran out in short order. The device collected dust in his room for some a while until he recently unearthed it, and noticed that a perfectly good PIR sensor was looking him in the face all this time.

He disassembled the air freshener, then set out to figure out how he could interface with the PIR sensor. After finding a helpful Instructable on the topic, he had full access to the sensor’s signals, allowing him to easily wire it up to an Arduino. He decided it would be fun to trigger some simple music any time someone entered his room, so he encoded a short bit of the Super Mario Brothers theme in RTTTL, as he explains in the video below.

It’s a simple little hack, but [Lochie] is pleased with it, and we imagine that he likely has a long list of other creative ideas in mind for his newly discovered PIR sensor.

Continue reading “Simple Hack Reuses An Air Freshener PIR Sensor” →

PlayStation 3 Controller Made Fully Remappable

October 11, 2011 by Mike Szczys 8 Comments

[Hazer] managed to take a PlayStation 3 SixAxis controller and modify it so that all of the buttons can be remapped in hardware. Aside from this being really cool, he had a good reason for doing it. Regular readers should remember the feature regarding [Chuck Bittner’s] internet petition calling for button mapping as a feature in all games. As the industry still hasn’t taken up the torch in this area, [Hazer] developed this mod for [Chuck] to use and has released it for any others out there who wish to give it a try.

The hardware alterations are pretty hardcore. On the left of the image, just below the rumble motor, a DIP microcontroller is nestled dead-bug style. This is a PIC 18F14K50. It’s running a bootloader, and has its own USB port on the opposite side of the controller. By cutting traces and soldering to vias, this chip intercepts button presses and shoots them off to the controller’s processor based on alternative mapping stored in EEPROM. There’s a helper app that lets you plug the controller into a computer to specify what each button does, including features like toggle for the buttons. Check out [Chuck’s] thoughts on the hardware in the video after the break.

Continue reading “PlayStation 3 Controller Made Fully Remappable” →

This Cube Of Playroom Drawers Is Quite Puzzling

October 11, 2011 by Mike Szczys 18 Comments

If you’re looking for a piece of custom furniture to anchor your child’s playroom, this Rubik’s cube chest of drawers is just the thing. [Makendo] went the extra couple of miles on the project, building the entire thing from scratch and adding one clever feature after another to make it something special.

It’s made up of three plywood boxes, open on one side to accept a plywood drawer. The drawers were carefully fitted so that it is difficult to see which side is actually the drawer face. [Makendo] even routed a hash-mark of grooves into each face of the cube to make it look like the seams that make up the 9×9 grid of colored squares. Speaking of those colors, the “stickers” themselves are made of 1/4″ plywood and are not permanently affixed. Each is held on with a magnet plus a pair of dowels to keep it from spinning. This way you can rearrange the colors as often as you please.

Each layer of the cube spins thanks to some lazy susan bearings. [Makendo] didn’t want to add too much distance between the different modules so he routed out each side to fit the circular hardware. As a final touch, the drawers themselves can be locked in place using a dowel underneath one of the colored squares. We’ve embedded a video of the cube at play after the break.

Continue reading “This Cube Of Playroom Drawers Is Quite Puzzling” →