Are You Smarter Than A Raccoon?

[Ben] has a raccoon problem. It seems that it’s not uncommon for him to come face-to-face with a pesky raccoon in the middle of the night, in his living room. We think most people would solve the problem by preventing the raccoon from entering the home. But [Ben] just seems hell-bent on catching him. Most recently he’s added motion-sensing to a live trap which he installed…. in his living room.

So [Ben] has cat’s which that to roam at night. They have free range thanks to a cat door which the hungry pest has been exploiting. Apparently the masked robber has a taste for cat food and that’s what keeps him coming back. [Ben] has been using the cat dish as bait but up to this point the live trap hasn’t worked. You see the raccoon isn’t going inside to get the food, but reaches through the cage and pulls pieces out one at a time. The solution is to put up a solid surface around the cage, and hope that the motion sensor will get him this time. Although we’ve linked the most recent post above, you’ll want to page through his blog for the whole story.

Wouldn’t it be better to install some kind of automatic lock that only lets in the kitty?

Continue reading “Are You Smarter Than A Raccoon?”

Stair Tricking Skateboard

This skateboard concept lets you travel down stairs almost as smoothly as gliding down a hill. This seems to be the eighth iteration in [PoChih Lai’s] attempts to add functionality to a board which will make it the ultimate ride for an urban outing. Check out the video after the break to see just how well he did.

We’ve seen hand carts that use six wheels to make stairs a breeze using a triad of wheels as a single-wheel replacement. This was actually the main concept early on in the design. But the drawback to this method is that the design takes up a lot of room and [PoChih] also made the deck much bulkier to keep you from getting a foot caught in the mechanism. The final design does away with the end-over-end concept and adopts a rocking mechanism. The board hangs from a bar which serves as the pivot between the two wheels. This way the wheels can absorb the brunt of the motions, and the base of the deck can slide across the fronts of the steps if needs be.

We were talking about this here at the Hackaday office and the point was made that this is like YT’s skateboard from Neal Stephenson’s Snow Crash. Did you hear that it’s headed to a theater near you?

Continue reading “Stair Tricking Skateboard”

Heading To MakerFaire Kansas City

Today, I’m heading out to Makerfaire Kansas City. I plan on covering this event quite extensively. If you see me, don’t hesitate to come up and introduce yourself. I may even have a custom cut vinyl hackaday sticker left for you. Since we are Hackaday, I plan on trying to get into the details and get interviews following [Ian Lesnet’s] lead. We don’t just want to see a neat thing on a table, we want to know how it works and what roadblocks that person ran into. See you there!

 

Hackaday Links: June 22, 2012

For when you want something huge machined

Turn your volume down for this video. It’s the HSM-Modal CNC mill carving a full-sized car out of styrofoam, applying clay to the foam core, and machining the clay at 50 meters per minute. Yes, we’ve seen this machine before, but never in action. It only took a little over 24 hours to make this full-size model car.

Microscope into a drill press

If you need to drill some PCBs, [wotboa] has a neat build for you. He built a micro drill press out of a microscope. It’s a damn good idea if you can find a quality microscope base; those things usually have exceptionally high precision. The ‘hack’ part is a $7 Harbor Freight rotary tool, some PVC pipe, and a PWM control for the motor – home-made, natch.

I’m telling you, they need to get [River] out of the library. Work on it [Moffat].

[Alan] made a TARDIS book case, and he decided to share the plans with us. Just the build to combat the severe lack of woodworking and Whovian stuff on Hackaday. Vashta Nerada hopefully not included.

Money can’t buy happiness, but you sure can sell it

[Greg] sent in some info on Disney’s ‘glow with the show’ hats they sell at the California Adventure park. For $25, you get a hat with RGB LEDs in the mouse ears that synchronize with the World of Color show every night. There’s a better description of the hats here, but we’re thinking these are very similar to the Coldplay Xylobands we saw at this year’s Grammys. Anyone want to tear some mouse ears apart?

An exceptionally low-tech radio telescope

[Impulse405] found a poor man’s radio telescope on Instructables and decided to share it with us. [Z0rb] found a 10-foot dish in the garbage and quickly absconded with this retro hardware. After adding a power supply and a meter-based total power receiver, [Z0rb] had a radio telescope that covered wavelengths from 850 to 2200 MHz.

Gooseberry Is The Latest ARM Linux Board

It looks like we’re finally seeing the proliferation of single board computers take off. The latest is called the Gooseberry. While it will cost about £40/$62 USD at release, it greatly outperforms the current crop of tiny Linux boards.

As the latest in what will be a long line of these ARM-ified single board computers, the Gooseberry hugely outperforms the VIA APC and Raspberry Pi with a Allwinner A10 CPU running at 1.2 GHz, 512 MB of RAM, and built-in WiFi. Basically, the Gooseberry has all the features you would expect from an Android tablet; the reason for this is because the Gooseberry actually is the board found in a few Chinese tablets.

There’s a few very nice features like an LVDS output to add LCD displays without hogging the HDMI output, and the form factor is incredibly thin making it perfect for building a small portable device.

After the break you can check out a walkthrough of the Gooseberry board along with evidence of it running Ubuntu.

Continue reading “Gooseberry Is The Latest ARM Linux Board”

Bringing Chromium To The Raspberry Pi

If you’re in possession of a Raspberry Pi, you may want to check out the new Chromium support for your tiny pocketable computer. With its terrifically minimal hardware requirements, the Chromium OS seems like just the thing for this $35 computer.

The new Raspberry Pi supported Chromium build comes from the fruitful desktop of [Hexxeh], a.k.a. [Liam McLaughlin]. In the world of Chromium devs, [Hexxeh] has already made a name for himself by getting Chromium working on a Macbook Air, putting it in a VirtualBox, and generally being the resident wizard of the Chromium project

The Chromium OS should provide a much faster computing experience for the Raspi compared to the current Debian and Arch Linux-based builds.   Right now, the Chromium support for the Raspberry Pi is very much a work in progress but a slimmed-down, browser-only operating system may be just what the underpowered but useful 700 MHz ARM computer with 256 MB of RAM needs.

NC Maker Faire 2012: Hackaweek Display

[youtube http://www.youtube.com/watch?v=gjtH3iA1YrY&w=470&h=315%5D

[Dino] has been featured here at [HAD] on many occasions, so I was excited to see some of his inventions in person and meet the man himself. [Dino] didn’t disappoint, bringing a display that included a working demonstration of his upcoming cover story for Make Magazine – an automatic doggie ball-thrower. Also there were some crazy musical instruments, what appeared to be a cylindrical oscilloscope display, and a robot rolling around with the thrown balls (and kids).

As seen in the video, one thing to remember if you’re displaying at a Faire, kids will definitely be there, and will interact with anything they can. This can be good or bad, so make sure you design your display, like [Hackaweek]’s to be the former. [Dino] also had a projector pointed at the wall playing some video. This made for a great attention-getter!  Check out the short videos below of his ball thrower in action and a view of the show from one of his robots! Continue reading “NC Maker Faire 2012: Hackaweek Display”