THP Hacker Bio: Michael R Colton

September 7, 2014 by Brian Benchoff 6 Comments

With many hackers out there realizing how much you can do with a few RF blocks connected to a computer, it’s no surprise software defined radio would make a showing in the semifinalists for The Hackaday Prize. [Michael]’s project is the PortableSDR, a small, self-contained unit that handles just about everything below 30MHz. No, [Michael] isn’t dealing with gigahertz accessible with fancier SDRs, but that’s not the point: PortableSDR is meant to do everything – vector analysis, a neat waterfall display, transmit and receive – in a small, portable package you can take anywhere. It’s also fairly cheap to build, and of course completely open source.

This isn’t [Michael]’s first rodeo; he’s built a number of equally cool projects before. He was kind enough to send in a short bio, available below.

Continue reading “THP Hacker Bio: Michael R Colton” →

Hackaday Links: August 30, 2014

August 31, 2014 by Brian Benchoff 18 Comments

Adafruit did another Circuit Playground, this time concerning frequency. If you’re reading this, no, it’s probably not for you, which is great because it’s not meant to be. If you have some kids, though, it’s great. Not-muppet robots and oscilloscopes. Just great.

The Hack42 space in Arnhem, Neterhlands recently got an offer: clean out a basement filled with old computer equipment, and it’s yours. Everything in the haul had to fit through an 80cm square door, and there are some very heavy, very rare pieces of equipment here. It’ll be a great (and massive) addition to their museum. There’s a few pics from the cleanout here and here.

[Mike] has been working on a project to convert gerber files into SVGs and it’s great.

[Carl] did a roundup of all the currently available software defined radios available. It’s more than just the RTL-SDR, HackRF, and BladeRF, and there’s also a list of modifications and ones targeted explicitly to the ham crowd.

This is a Facebook video, but it is pretty cool. It’s a DIY well pump made in Mexico. A few rubber disks made out of an old inner tube, a bit of PVC pipe, and a string is all you need to bring water to ground level.

What can you do with a cellphone equipped with a thermal imaging camera? Steal PIN codes, of course. Cue the rest of the blogosphere sensationalizing this to kingdom come. Oh, what’s that? Only Gizmodo took the bait?

About a year ago, we saw a pretty cool board made by [Derek] to listen in on the CAN bus in his Mazda 3. Now it’s a Kickstarter, and a pretty good one at that.

Your connectors will never be this cool. This is a teardown of a mind bogglingly expensive cable assembly, and this thing is amazing. Modular connectors, machined copper shields, machined plastic stress relief, and entire PCBs dedicated to two caps. Does anyone know what this mated to and what the list price was?

DEFCON 22: The HackRF PortaPack

August 17, 2014 by Brian Benchoff 12 Comments

What do you get when you combine one of the best (and certainly one of the best for the price) software defined radios with the user interface of a 10-year-old iPod? The HackRF PortaPack, developed by [Jared Boone], and demonstrated at DEFCON last weekend.

[Jared] is one of the original developers for the HackRF, a 10MHz to 6GHz software defined radio that can also transmit in half duplex. Since the development of the HackRF has (somewhat) wrapped up, [Jared] has been working on the PortaPack, an add-on for the HackRF that turns it into a portable, ARM Cortex M4-powered software defined radio. No, it’s not as powerful as a full computer running GNU Radio, but it does have the capability to listen in on a surprising amount of radio signals.

Because [Jared] is using a fairly low-power micro for the PortaPack, there’s a lot of tricks he’s using to get everything running smoothly. He gave a lightning talk at the Wireless Village at DEFCON going over the strengths and weaknesses of the chip he’s using, and surprisingly he’s using very little floating point arithmetic in his code. You can check out the video for that talk below.

Continue reading “DEFCON 22: The HackRF PortaPack” →

Building The NSA’s Tools

August 1, 2014 by Eric Evenchick 8 Comments

Back in 2013, the NSA ANT Catalog was leaked. This document contained a list of devices that are available to the NSA to carry out surveillance.

[Michael Ossmann] took a look at this, and realized that a lot of their tools were similar to devices the open source hardware community had built. Based on that, he gave a talk on The NSA Playset at Toorcamp 2014. This covered how one might implement these devices using open hardware.

The above image is a parody of an ANT Catalog page, which shows [Michael]’s HackRF, an open source software defined radio. In the talk, [Michael] and [Dean Pierce] go over the ANT Catalog devices one by one, discussing the hardware that would be needed to build your own.

Some of these tools already have open source counterparts. The NIGHTSTAND WiFi exploitation tools is essentially a WiFi Pineapple. SPARROW II is more or less a device running Kismet attached to a drone, which we’ve seen before.

A video of the Toorcamp talk is available on [Michael]’s blog. There will also be a variety of talks on this subject at DEFCON next week, which we’re looking forward to. For further reading, Wikipedia has a great summary of the ANT Catalog.

Hackaday Links: July 27, 2014

July 27, 2014 by Brian Benchoff 14 Comments

Taking apart printers to salvage their motors and rods is a common occurrence in hacker circles, but how about salvaging the electronics? A lot of printers come with WiFi modules, and these can be repurposed as USB WiFi dongles. Tools required? And old printer, 3.3 V regulator, and a USB cable. Couldn’t be simpler.

The Raspberry Pi has a connector for a webcam, and it’s a very good solution if you need a programmable IP webcam with GPIOs. How about four cameras?. This Indiegogo is for a four-port camera connector for the Raspi. Someone has a use for this, we’re sure.

The one flexible funding campaign that isn’t a scam. [Kyle] maintains most of the software defined radio stack for Arch Linux, and he’s looking for some funds to improve his work. Yes, it’s basically a ‘fund my life’ crowdfunding campaign, but you’re funding someone to work full-time on open source software.

Calibration tools for Delta 3D printers. It’s just a few tools that speed up calibration, made for MATLAB and Octave.

[Oona] is doing her usual, ‘lets look at everything radio’ thing again, and has a plan to map microwave relay links. If you’ve ever seen a dish or other highly directional antenna on top of a cell phone tower, you’ve seen this sort of thing before. [Oona] is planning on mapping them by flying a quadcopter around, extracting the video and GPS data, and figuring out where all the other microwave links are.

PowerPoint presentations for the Raspberry Pi and BeagleBone Black. Yes, PowerPoint presentations are the tool of the devil and the leading cause of death for astronauts*, but someone should find this useful.

* Yes, PowerPoint presentations are the leading cause of death for astronauts. The root cause of the Columbia disaster was organizational factors that neglected engineer’s requests to use DOD space assets to inspect the wing, after which they could have been rescued. These are organizational factors were, at least in part, caused by PowerPoint.

Challenger was the same story, and although PowerPoint didn’t exist in 1986, “bulletized thinking” in engineering reports was cited as a major factor in the disaster. If “bulletized thinking” doesn’t perfectly describe PowerPoint, I don’t know what does.

As far as PowerPoint being the leading cause of death for astronauts, 14 died on two shuttles, while a total of 30 astronauts died either in training or in flight.

Homebrew NSA Bugs

July 10, 2014 by Brian Benchoff 56 Comments

NSA

Thanks to [Edward Snowden] we have a huge, publicly available catalog of the very, very interesting electronic eavesdropping tools the NSA uses. Everything from incredibly complex ARM/FPGA/Flash modules smaller than a penny to machines that can install backdoors in Windows systems from a distance of eight miles are available to the nation’s spooks, and now, the sufficiently equipped electronic hobbyist can build their own.

[GBPPR2] has been going through the NSA’s ANT catalog in recent months, building some of the simpler radio-based bugs. The bug linked to above goes by the codename LOUDAUTO, and it’s a relatively simple (and cheap) radar retro-reflector that allows anyone with the hardware to illuminate a simple circuit to get audio back.

Also on [GBPPR2]’s build list is RAGEMASTER, a device that fits inside a VGA cable and allows a single VGA color channel to be viewed remotely.

The basic principle behind both of these bugs is retroreflection, described by the NSA as a PHOTOANGLO device. The basic principle behind these devices is a FET in the bug, with an antenna connected to the drain. The PHOTOANGLO illuminates this antenna and the PWM signal sent to the gate of the FET modulates the returned signal. A bit of software defined radio on the receiving end, and you have your very own personal security administration.

It’s all very cool stuff, but there are some entries in the NSA catalog that don’t deal with radio at all. One device, IRATEMONK, installs a backdoor in hard drive controller chips. Interestingly, Hackaday favorite and current Hackaday Prize judge [Sprite_TM] did something extremely similar, only without, you know, being really sketchy about it.

While we don’t like the idea of anyone actually using these devices, the NSA ANT catalog is still fertile ground for project ideas.

Continue reading “Homebrew NSA Bugs” →

A GSM Base Station With Software Defined Radio

July 5, 2014 by Brian Benchoff 40 Comments

gsm If you’re wondering how to get a better signal on your cellphone, or just want to set up your own private cell network, this one is for you. It’s a GSM base station made with a BeagleBone Black and a not too expensive software defined radio board.

The key component of this build is obviously the software defined radio. [Julian] is using a USRP B200 radio for this project. It’s not cheap, but it is a very nice piece of hardware capable of doing just about anything with GNU Radio. This board is controlled by a BeagleBone Black, a pretty cheap solution that puts the total cost of the hardware somewhere around $750.

The software side of the build is mostly handled by OpenBTS, the open source project for the software part of a cell station. This controls the transceiver, makes calls and SMS, and all the backend stuff every other cell station does. OpenBTS also includes support for Asterisk, the software of choice for PBX and VoIP setups. Running this allows you to make calls and send texts with your SDR-equipped, Internet-enabled BeagleBone Black anywhere on the planet.