Halloween Hacks: A Radioactive Display With More Trick Than Treat

November 1, 2011 by Mike Nathan 11 Comments

Halloween Hacks Banner

radioactive_barrel_display

[Shawn] was looking for a way to shake up his decorations this Halloween and decided to build a new prop for his front yard. He had a pair of old oil barrels in his garage and thought they would look great with a little bit of work.

He bolted the pair of barrels together, then slapped a fresh coat of black paint on them before adding a bright yellow radiation trefoil to each one. One barrel contains a pneumatic piston that opens the lid, revealing a light up pumpkin, a fog machine, and a set of water nozzles that spray the area. The second drum houses an air compressor, a wireless router, and an IP camera for recording the action. A web-enabled Arduino triggers the lid and sprayer, both of which can be controlled from the comfort of his house.

We think it’s a creative use of some old scrap barrels, but we’re hoping he doesn’t plan on wetting trick-or-treaters that pass through, as it seems like a good way to get your house egged or otherwise vandalized on Halloween. If the water sprayer were perhaps swapped out with some other cool effects, [Shawn] is far less likely to be the target of some angry, wet teenagers.

Be sure to check out the video below to see the display in action.

Continue reading “Halloween Hacks: A Radioactive Display With More Trick Than Treat” →

Turning LEDs Into A Camera

November 1, 2011 by Brian Benchoff 17 Comments

[Udo] figured out how to turn a bunch of LEDs into a very low resolution camera.

The build is based around [Udo]’s Blinkenlight shield he’s been developing over the past year. The camera operates under the idea that there’s really not much difference between a LED and a photodiode; LEDs can do light emission and detection. In actuality, the LED ‘camera’ isn’t all that different from a linear CCD array, the type of image sensor in flatbed scanners.

After connecting his Blinkenlight shield to his Arduino and computer, [Udo] wrote a sketch that would capture 17 values from his LED camera. These values are shot over the serial connection where high levels of light show up as smaller numbers and low light levels are understood as larger numbers.

[Udo] has been doing a lot of other cool stuff with his Blinkenlight shield, like a persistence of vision experiment and pretending to be [Michael Knight]. Check out the video after the break for a demo of [Udo]’s linear LED camera.

Continue reading “Turning LEDs Into A Camera” →

Looking Toward Christmas Decor By Learning About DMX

November 1, 2011 by Mike Szczys 8 Comments

So Halloween finally arrived, we hope you had enough time to pull off your frightening feats in the way you had originally envisioned. Now it’s time again to look to the future and start planning this year’s Christmas decorations. Lights are always a popular theme, and this year you might want to look into DMX lighting controls and decide if that’s a route you want to take. [Akiba] has your back, he just put together a set of videos explaining the DMX lighting protocol and how to use it with an Arduino.

The thought here is that the Arduino can be used as a sort of DMX hub that is connected directly to a computer running open source controller hardware. It can send commands which the Arduino decodes, deciding whether to just pass them on to DMX compatible devices, or to do what it does best and control other hardware that is not normally accessible through the lighting command protocol. To the control program your four-dollar strand of LED lights looks no different from a thousand dollar stage light, making it cheap and easy to build your own entertaining holiday show right in your front yard. See the second video in this series after the break where [Akibo] details the hardware setup for his system. The other parts are available at the link above.

Be careful, this can be a consuming endeavor. Don’t believe us? Just look around and you’ll find no shortage of large DMX builds just for Christmas lights.

Continue reading “Looking Toward Christmas Decor By Learning About DMX” →

Wine-o-Meter Quantifies Your Bachelor Party Bad Behavior

October 31, 2011 by Mike Nathan 6 Comments

wine_o_meter

[Phil] had a bunch of Shiftbrite modules set aside for an LED table project, but before he could get around to it, he decided to use them to build a prop for his friend’s bachelor party. Expecting plenty of drunken revelry, he constructed the Arduino Wine-o-Meter – a carnival “Test your strength” style breathalyzer.

The 25 Shiftbrite modules are lined up in a column, which is connected to an Arduino tucked away in a cardboard box. The Arduino takes readings from an MQ-3 Gas/Alcohol sensor was salvaged from another breathalyzer build [Phil] put together. While it has been noted in the past that this sensor is pretty inaccurate, it seems to serve his purposes quite well. Since his game is based on measuring the players’ blood alcohol content in relation to one another rather than obtaining an exact BAC reading, the poor calibration of the device should affect everyone equally.

It looks pretty cool, and we imagine that it will ensure that the party stays lively throughout the wee hours of the night. Check out the video below to see [Phil] walk you through a demo of his Wine-o-Meter.

Continue reading “Wine-o-Meter Quantifies Your Bachelor Party Bad Behavior” →

Salvaged Flight Stick Controls A/V System, Triggers “Emergency Party System”

October 31, 2011 by Mike Nathan 16 Comments

av_controller_party_switch

After seeing a writeup online that demonstrated how to build an “Emergency Party Button”, [spikec] knew that he had to have one of his own. He happened to have a USAF B-8 stick grip from an A-10A aircraft laying around, and figured it would be perfect for controlling the A/V system in his basement.

The control stick was mounted to the top of a cheap cigar humidor, and crammed full of any electronic component he could get his hands on. It contains not one, but two Arduinos. The first is tasked with reading the flight stick’s inputs and the IR control of his various appliances, while another triggers the overhead lighting in his bar along with the X10 controlled Emergency Party System. He contemplated combining all of the functionality into one device, but splitting the tasks in two was easier for this self-declared electronics novice.

The various buttons on the control stick can be used to power all of his A/V appliances on and off, control volume levels, and select which songs stream from his digital jukebox. If the action ever starts to wind down, a quick turn of his “arming” key and the flick of a switch sends his basement into full-on party mode, which includes more lighting and lasers than any one person should be allowed to own.

[spikec] says that his wife’s eyes were rolling like “uncaged gyros” when he unveiled his controller for the first time – a sign of a job well done. Don’t take our word for it though, check out a video of his control stick and Emergency Party System in action after the jump.

Continue reading “Salvaged Flight Stick Controls A/V System, Triggers “Emergency Party System”” →

Arduino Controlled Four Socket Outlet

October 31, 2011 by Brian Benchoff 27 Comments

Never get between a man and his salami. [Mike] needed a way to control temperature, humidity and airflow with his meat curing setup. Of course he could modify a refrigerator and humidifier to be controlled separately, but [Mike] decided the best course of action would be to control line voltage with an Arduino.

[Mike] started his build with a four socket wall housing he picked up at Home Depot for a few dollars. After wiring up each outlet so it can be controlled independently, he set out designing a four port relay board. This was a pretty simple build – four 10 Amp relays and a few terminal blocks. The PCB was designed in Eagle as a single-side board for ease of manufacturing.

The relay board is meant to fit inside the blue box along with the four sockets, so a few holes were drilled for the power and control wires. The entire assemblage was put together and tested out. [Mike] posted a video of his controllable outlet flashing a light bulb at 10 Hz. Check out that light switch rave after the break.

Continue reading “Arduino Controlled Four Socket Outlet” →

Halloween Hacks: A Light And Music Show Fit For [Jack Skellington]

October 28, 2011 by Mike Nathan 4 Comments

Halloween Hacks Banner

singing_pumpkin_halloween_show

[Greg] was looking for something to build using his recently acquired Arduino, and with Halloween approaching, he thought a cool light display would make a great project. He browsed around online and found this tutorial that shows how to build a chorus of singing pumpkins controlled by a computer’s parallel port. Since he didn’t have any computers with a parallel port kicking around anymore, he decided to try his hand at recreating it with an Arduino.

[Greg] gathered eight light up Jack-o-Lanterns, along with a handful of relays and other miscellaneous components. He wired up the relays to trigger each individual pumpkin’s built in light when switched by the Arduino. He sat down and carefully listened through “This is Halloween” from The Nightmare Before Christmas, choreographing each of the pumpkins to take on the voice of one of the movie’s characters.

When the show begins, the display transforms from a group of unassuming pumpkins with candles a-flicker to a chorus of ghouls extolling the virtues of Halloween.

It really is fun to watch, so be sure to check out the video below. If you’re looking to throw together a quick display before the big day rolls around, [Greg’s] source code and diagrams should get you headed in the right direction.

Continue reading “Halloween Hacks: A Light And Music Show Fit For [Jack Skellington]” →