SNES Emulator Has It’s Slot Sealed Shut

October 19, 2012 by Mike Szczys 24 Comments

If you look closely you’ll notice there’s nowhere to put the game cartridge on this Super Nintendo system. That’s because this is a Rasberry Pi based SNES emulator that plays ROMs, not cartridges. Since the RPi board is used the only limit to what you can play is the board’s RAM and which ROMs you have on the SD card.

The case has basically been gutted and the unused cartridge slot was sealed with some Bondo before painting. In addition to the Rasberry Pi you’ll find a 7-port powered USB hub and a Teensy microcontroller board. The hub allows for the controllers to be connected via USB. The Teensy is recognized as a USB HID device and is used to connect the reset button to a functions on the emulator program. The power switch still works too. To make this happen [MIDItheKID] spliced a USB connector and a microB USB connector to the power switch. We think this draws power from the hub but we’re not 100% sure.

[MIDItheKID] mentions in the Reddit comments that he’s thinking of grabbing that new RPi that has more memory and doing some similar work on his dead PSX.

Robot Performing A Tightrope Act

October 19, 2012 by Mike Szczys 21 Comments

This robot is able walk the tightrope (translated). Well, it’s more of a shuffle than a walk, but still a lot better than we could do.

In the video after the break you can see the bot starting on the platform to the right. As it steps out onto the wire (which rides in a groove on the bottom of its foot) the robot spreads its arms to help maintain balance. When the other foot leaves the platform that is the last stride we will see until it reaches the other side. The rest of the act consists of sliding the feet a little bit at a time until it gets all the way across.

[Dr. Guero] has been working on at least one other balancer as well. Also embedded after the break is a robot riding a bicycle. It actually puts a foot down when stopped, and gives a stuttering push-off to get going again. This guy would be right at home riding past you in the hallways of the Death Star.

Continue reading “Robot Performing A Tightrope Act” →

APRS IGate Built Using A Raspberry Pi

October 19, 2012 by Mike Szczys 28 Comments

The hardware seen above is used to bridge a local RF radio network to the APRS-IS network. The APRS-IS is an Internet Service that uses a web connection to communicate between APRS networks in different parts of the world. The Raspberry Pi is perfect for this application because of its ability to connect to a network, and its native use of Linux.

On the software side the majority of the work is done by a Python script. It is responsible for setting up and monitoring a connection with an APRS-IS server. To connect to the handheld radio unit a USB sound card was used. The Multimon package is used to send and receive audio packets through this hardware.

[Sunny] has a few upgrades planned for the system. The device needs to report its location to the APRS-IS server and the plan is to add functionality that will look of the WiFi AP’s location automatically. It may also be possible to get rid of the radio all together and use a DVB dongle as a software defined radio.

Red-bullet: Cooking Stove From Cans, Fueled By Gas Additive

October 19, 2012 by Mike Szczys 25 Comments

A couple of beverage containers and a little bit of fuel additive bring together this aluminum can stove project. When lit it shoots flames out each of those holes around the top to heat the vessel resting upon it. [Peter Geiger] calls it the Red-Bullet because one of the stove pieces started as a Red Bull can and the other piece was a Coors (aka silver bullet).

This is basically an alcohol stove. We remember seeing a very well designed version of the penny stove several years back. This is different as it uses a side burner so the stove itself functions as the kettle stand. [Peter] started by cutting the Red Bull can just a bit taller than the final height. He then inserted the top portion of one of those aluminum beer cans that are shaped like glass bottles. The neck was lopped off and inverted. It is joined with the other can base using JB weld and by rolling the aluminum in on itself. After that has dried the holes are added and it’s filled with HEET from a yellow bottle. This gasoline additive is meant to sequester water and keep your gas line from freezing. The yellow bottle is mainly alcohol, the red is methanol so make sure you use the right one!

Building A Raspi Case In True Hackaday Fashion

October 19, 2012 by Brian Benchoff 12 Comments

[Ben] needed a case for his Raspberry Pi. Instead of going the usual laser-cut plastic or 3D printed route, he took a path far more familiar to us here at Hackaday. His case is built out o f aluminum found in his basement, providing a neat reuse for some old aluminum extrusion he had lying around.

Part one of [Ben]’s thoroughly documented build goes over the process of acquiring some of this very handy aluminum extrusion. Part two covers a very neat feature of [Ben]’s scrap of aluminum: because of a pair of internal chamfers, [Ben] was able to mount his Raspi and USB hub to a separate piece of PVC and slide the whole assembly in.

The final assembly included dremeling a piece of aluminum plate for the Raspi and USB hub ports and wiring the whole thing together.

Right now the newly enclosed Raspi is working happily as [Ben]’s home server. Not exactly the use case a rugged aluminum case would see the best use from, but it looks great all the same.

Stacking GPS, GSM, And An SD Card Into An Arduino Shield

October 19, 2012 by Brian Benchoff 18 Comments

A few years ago, [Phang Moh] and his compatriots were asked by a client if they could make a vehicle tracking device for oil tankers all around Indonesia. The request of putting thousands of trackers on tanks of explosives was a little beyond [Phang Moh]’s capability, but he did start tinkering around with GPS and GSM on an Arduino.

Now that tinkering has finally come to fruition with [Phang]’s TraLog shield, a single Arduino shield that combines GPS tracking with a GSM and GPRS transceiver. There’s also an SD card thrown in for good measure, making this one of the best tracking and data logging shields for the Arduino.

The shield can be configured to send GPS and sensor data from devices attached to an I2C bus to remote servers, or a really cool COSM server. [Phang] is selling his TraLog for $150, a fairly good deal if you consider what this thing can do.

Seems like the perfect piece of kit for just about any tracking project, whether you want to know the location of thousands of oil tankers or just a single high altitude balloon.

Tip ‘o the hat to [Brett] for finding this one.

Hackaday Retro Edition Roundup

October 19, 2012 by Brian Benchoff 13 Comments

It’s time for another update chronicling the adventures and misadventures of getting really old computers to load our retro edition!

First up is [Andrew Hull] and his brilliant use of a Raspberry Pi to get an old Psion 5mx PDA on the Internet. The Raspi served as a wireless bridge, taking in Internet from a WiFi dongle and sending it back out via a serial port. Here’s a great guide for enabling PPPD on the Raspi, and giving just about anything with a serial port an Internet connection.

It may push the limits of being a retro submission, but [Glen]’s use of a modem to get on the Internet calls to us like a siren song.

Did you know Corel made computers? Well, [Victor] has one, and it’s actually a pretty interesting machine. ARM processor, an actual hard drive, and dual Ethernet ports. It was built in the late 90s and the hard drive has since died, but [Victor] booted it into Red Hat over his network and loaded up our retro site.

Finally, we come to [Greg]’s submission. He could have sent in a Mac SE/30 submission, but figured that was old hat (do you see one on there, [Greg]. No. And it’s the best computer Apple will ever make). Instead, he had an old Powerbook Duo 2300c with a Duo 230 screen lying around.

Powerbook Duos are pretty weird; they only had two ports – a single DIN-8 serial port and a dock connector. [Greg] had a Powerbook Duo dock that surprisingly had an Ethernet port. Third-party peripherals to the rescue, it seems. After plugging his Duo to his network and launching iCab, [Greg] was able to browse both the retro and main Hackaday editions. Picture Not bad for the smallest laptop Apple made before the Air.

Oh, [Greg] was also cool enough to write a tutorial for getting just about every Macintosh on the Internet. We’ve put that up on the retrocomputing guide portion of our retro site, and we’re always looking for new submissions.

You can check out the pics from all these submissions in a Web 2.0 WordPress gallery after the break, or head on over to the retro site and view them the way the gods of HTML intended.

Continue reading “Hackaday Retro Edition Roundup” →