Building A Spectrophotometer

December 13, 2010 by Mike Szczys 15 Comments

What can you make with a toilet paper roll, duct tape, and a graphing calculator? A stand for your homemade spectrometer. This is neither as pretty nor as accurate as a precision scientific instrument, but that doesn’t mean it’s useless. In fact, it works perfectly well for rudimentary observations. Light is shined through a sample solution, passes through a diffraction grating, then shows up as bands of color on the projection surface seen above. The photosensor mounted on the cardboard tube was pulled from a night-light, and is read using the ruler and the multimeter. This results in two data units that are used to graph the results. As long as you’re running test samples as a control this simple setup will yield useful information for the scientist on a shoe-string budget.

[via BoingBoing]

DIY Clamp Helps With Surface Mount Soldering

December 13, 2010 by Mike Szczys 30 Comments

Hackaday writer [Gerrit Coetzee] built a simple clamp to aid in surface mount component soldering. This cheap, easily made device uses gravity to hold tiny components in place. The tip of the bolt is pointed, but gently like a ballpoint pen so as not to harm the components with a sharp tip. Roughly position your component, rest the tip of the clamp on its center, then nudge for final positioning. [Gerrit] also points out that this acts as a heat sink, helping to prevent damage to the component if you’re too lethargic with the soldering iron.

It seems like this device has been around in one form or another for quite a long time. But the best ideas do keep on popping up. Another nice tip to go along with this one is the use of a dowel when ironing during toner transfer for your PCBs.

Putting Too Many Horses In A Golf Cart

December 13, 2010 by Mike Szczys 49 Comments

Want to put 100 horses into your golf cart and then take it to the Dragstrip? Why not? [Mac McAlpine] did just that by dropping a 2007 GSXR 600 EFI into a 1987 gas-powered Yamaha golf cart. After the break you can see a video of the test run, as well as an overview of the modifications made when swapping engines. [Mac] mentions that the setup still uses the stock bike chain and jackshift even with the upgrade in power. He has, however, upgraded both the front and rear axles with caliper and drum brakes respectively. There’s also a NASCAR Car of Tomorrow wing on the roof to help keep the wheels on the pavement.

Good thing he’s wearing that helmet. Without a seatbelt it’ll make smashing through the windshield a little more comfortable. Drive carefully [Mac]!

Continue reading “Putting Too Many Horses In A Golf Cart” →

Game Boy VGA Using An FPGA

December 12, 2010 by Mike Szczys 27 Comments

[ViDAR] was looking for a project to keep him occupied and settled on creating a VGA converter for his Game Boy. He had some difficulty finding pinouts for the LCD and CPU but working with what was known, and an oscilloscope, he found the necessary signal. Tap into just a few lines using those thin blue wires; Vsync, Hsync, clock, and two data pins. From there a development board with an Altera Cyclone II field-programmable gate array takes care of the heavy lifting. The board already has hardware for a VGA connection so it was just a matter of processing the incoming signals into the VGA standard. His demo video is embedded after the page break.

Want a dedicated solution? Check out this Game Boy video adapter inside a VHS cassette.

Continue reading “Game Boy VGA Using An FPGA” →

Jacob’s Ladder Using EL Wire

December 12, 2010 by Mike Szczys 19 Comments

For Halloween [Paul] wanted to build a Jacob’s Ladder without the peril that working with high voltage might bring. He was inspired by a sequencer board for electroluminescent wire and decided to build a Jacob’s Ladder simulator using the glowing material. What he ended up with is quite convincing. Eight segments of EL wire have been mounted between two diverging towers. When a PIR sensor detects motion in the room, an Arduino switches on the simulation, playing a recording of the classic sizzling voltage sound while using the sequencer board to flicker the wires from bottom to top. See for yourself in the video after the break. We give [Paul] bonus points for constructing the base out of Lego.

But if you’re not one for being cautions, there’s always this real Jacob’s Ladder build. Or maybe you just want to make something glow with the EL wire.

Continue reading “Jacob’s Ladder Using EL Wire” →

Kids Type With Their Eyes, Robot Arm Prints Their Words

December 11, 2010 by Mike Szczys 12 Comments

F.A.T. took it to the next level, combining a couple of their projects for the Cinekid festival. This contraption lets kids write their names with their eyes for printing by a robot arm. The first part is a glasses-free version of the EyeWriter, originally developed as an assistive technology. The system uses some IR LEDs to generate a reflection on your eye that a PS3 camera can pick up and use to precisely track your gaze. Just look at each key on a virtual keyboard to spell out your message. From there, a robot arm used previously in the Robotagger project prints out the name on a big sheet of paper the kids can take home. This is cool, but more importantly it’s a great way to inspire the next generation of hackers and engineers. Check out the video after the break.

Continue reading “Kids Type With Their Eyes, Robot Arm Prints Their Words” →