Year: 2011

Karate Chop Is Simon Without All The Touching

September 15, 2011 by 9 Comments

[Alan Parekh] and his daughter [Alexis] just premiered their entry in the Avnet Dog Days of Summer contest. It’s a game called Karate Chop that is basically an electronic Simon Says. The video after the break shows a demonstration of the device. When switched on it’ll play a little tune and start cycling the LEDs on the front of the case. Players interact by breaking the infrared beams in the two cutouts on either side of the case. You need to keep your hand flat to do this, which is where the name comes from. There are four different game modes which are selected at the start of the game. There are two difficulty levels of a Simon Says game which shows the player a pattern in light and sound, then watches for the user to repeat that pattern back. The other mode that [Alexis] demonstrates is a reflex game which requires the player to quickly react to randomly illuminated LEDs.

The circuit is built on a breadboard hiding behind the front bezel and uses a PIC 16F1827 microcontroller to drive the game. The case itself is made from laser cut MDF and plywood. We’re not sure how much time [Alan] spent on the case, but we think it looks wonderful. If you’re planning to participate in the contest you better get rolling, the entry deadline is tomorrow.

Continue reading “Karate Chop Is Simon Without All The Touching” →

Build Your Own CT Scanner

September 15, 2011 by 29 Comments

[Linas] built himself an x-ray generator for a scholarship contest. We assume this wasn’t enough of a challenge for [Linas] because after the x-ray generator was done, he used his project to model objects in 3D (Google Translate link). It’s an amazing build, leaving us feeling sorry for the guy that came in second place to the home-made CT scanner.

The theory behind a CT scanner is fairly simple – take a series of x-rays of an object around an axis of rotation. From there, it’s a fairly simple matter to digitize the x-ray images to produce a 3D model. The hard part is building the x-ray generator. [Linas] used directional x-ray tubes, a few power supplies and from what we can gather x-ray film instead of a CCD sensor. The film was scanned into a computer and reassembled to get a 3D image.

[Linas] doesn’t seem too keen on giving away the schematics for his build to any old joker on the Internet because of the high voltage and radiation components of his build. Still, it’s an amazing build.

Check out the YouTube demo of [Linas]’s CT scanner imaging an old computer mouse and a reconstruction of the same data done in MATLAB after the break.

Continue reading “Build Your Own CT Scanner” →

Microchip Puts Up Two $1000 Prizes For USB And TCP/IP Stacks!

September 15, 2011 by 37 Comments

microchip_call_for_open_source

A couple of weeks ago we put up a post titled Addressing Microchip’s open source problem where we talked about some of their shortcomings as far as open source code goes, specifically the TCP/IP stack and the USB stack. The comments were predictably fairly negative. The interesting part here is that Microchip actually listened. If you read through all of the comments, you will get a bit of an inside look at what is going on internally at Microchip. At the very end, [Marc] from Microchip left a couple of comments outlining a pair of prizes for independently ported stacks for TCP/IP and USB. Microchip can’t fully open the ones that they have because of legal reasons so they need the help of the development community and they are putting up $1000 for each one to prove that they are serious. If you follow this link you will arrive at a page outlining the rules for the contest.

The gauntlet has been dropped! Do you have chops to pull this off and earn yourself a cool $1000?

ATtiny Hacks: An Audio Alert For Cell Phones Accidentally Left On Vibrate

September 15, 2011 by 31 Comments

ATtiny Hacks Theme Banner
vibe2tone_cell_phone_vibration_alert

[John Thomson] usually keeps his phone on vibrate when it’s in his pocket, and he often forgets to turn the ringer back on when setting it down to charge. This typically results in a bunch of missed calls in the meantime, so he had to devise a way to counteract his forgetfulness.

You might remember [John] from the Santa-pede contest we held last December. He wanted to try his hand at yet another competition, the Avnet Dog Days of Summer contest, so he scrambled to come up with a quick fix for his situation. He concocted a simple circuit based on [ChaN’s] design for a “Simple SD Audio Player with an 8-pin IC” that would alert him to incoming calls, even when his phone was on vibrate.

[John] used an ATtiny85, just as [ChaN] did, adding a speaker for sound output and a piezo sensor to detect his phone’s vibrations. When the piezo senses a bit of motion, the audio player kicks in, blaring a series of sounds that are sure to get [John’s] attention.

Record Sound Without A Microcontroller

September 15, 2011 by 14 Comments

For his A-level electronic course work, [Andrew] decided to build a digital sound recorder that doesn’t use a microcontroller.

[Andrew]’s build captures audio from an on board microphone at 8000 samples/second. The audio is digitized into 8-bit sound data and sent to an SRAM. The recording and playback functions are controlled entirely by 4000-series logic chips. He admits the sound quality is pretty poor; this is mostly due to the 8kHz sample rate. In some circles, though, a terrible sample rate is seen as being pretty cool so we’re not going to say [Andrew]’s build is useless.

There’s some pretty smart design choices in [Andrew]’s build, like a cut off filter on the microphone set at 4000 Hz (the Nyquist frequency of his system).  For the recording medium, he used an SRAM that can hold about half a megabyte of data. At 8000 samples/second,  [Andrew]’s build can store a little more than 60 seconds of audio. The build may not be a logic chip computer, but there’s not any question in our mind that [Andrew] learned something. Check out [Andrew]’s 66-page coursework report here (PDF warning).

Adding A Little Polish To Your Cellphone Charging Setup

September 14, 2011 by 18 Comments

Cable management can really be an eyesore, but a little creative camouflage and you can have a cellphone charging station that also serves as decoration.

[Kitesurfer] wanted to use one of the cubbyholes in his new Ikea book shelf for charging but wasn’t keen on the rat’s nest of wires that would go along with it. Also not wanting to take on the challenge of wireless charging he hit the As-Is section of the home furnishing giant and grabbed a leftover board that matched the same finish as the cabinetry. It now serves as a false-back for the charging center behind which a power strip and wall-warts hide.

This covers up the problem, but a blank white box filled with the business end of the charging wires isn’t a whole to better. As with a magic show, the trick is in redirection. [Kitesurfer] cut a hole in the false-back and added the guts of a digital picture frame. Right now he’s got it scrolling through different charging icons, but it’s easy enough to change up the slide-show if he gets tired of them. We’d love to see a subsequent hack that lets the picture frame access the photos on your phone via Bluetooth.

Amp Hour Interviews [Joe Grand]

September 14, 2011 by 6 Comments

The Amp Hour, a podcast of electronics enthusiasts and professionals alike, just did an epic interview with [Joe Grand]. Along with hosts [Chris Gammell] and [Dave Jones], the discussion runs the gamut of points of interest in the hardware hacking world. The first vignette explores the rise, run, and fall of Prototype This, an engineering-centric TV show that [Joe] did along with a group of various engineers for the Discover Channel. He politely discusses some of the goods and bads of the TV business and how that affected the team’s ability to go into great detail about the projects they were building.

From there the guys discuss the development of Hackerspaces through the years. [Joe] has some concerns about the injection of corporate sponsorships in these DIY spaces and what that may mean in the long run. He then talks about the impending release of his 3-year-long laser range-finder project (we’ve seen a project using a prototype of this sensor). The show is rounded out with discussions about hardware fab houses that [Joe] uses and has used over the years for projects like the Defcon Badges (we loved his Defcon 18 badges).

It’s a great episode so download a copy and set aside about an hour to listen to the whole show.