Parts

811 Articles

Parts: Analog Distance Sensors (Sharp GP2D12/2Y0A02)

February 24, 2009 by 23 Comments

[youtube=http://www.youtube.com/watch?v=iGiRK0vmcUw]

Sharp GP2D12 and 2Y0A02 infrared rangers output a voltage proportionate to the distance of an object from the sensor.  The GPD12 senses objects at a distance of 10-80cm, while the 2Y0A02 has twice the range.

We’ve previously looked at the Sharp GP2Y0D02 digital proximity sensor. It only signals the presence of objects, while the GP2D12 and 2Y0A02 measure distance to them. If you’ve got a GP2YoD02, it might still be possible to tap the analog output. We’ll show you how use these sensors below.

Continue reading “Parts: Analog Distance Sensors (Sharp GP2D12/2Y0A02)” →

Parts: I2C Audio Volume Potentiometer (DS1807)

February 16, 2009 by 7 Comments

ds1807ii

The DS1807 contains two logarithmic digital potentiometers (pots) for audio volume adjustment. Each pot has 64 volume levels plus a mute setting. The volume level of each pot is set over a two-wire I2C serial interface. We’ll show you how to connect and interface the DS1807 below.

Continue reading “Parts: I2C Audio Volume Potentiometer (DS1807)” →

Tools: Smart Tweezers

February 13, 2009 by 52 Comments

We’re big fans of surface mount parts. SMD components are cheaper, take less board space, and don’t require drilling; all the coolest new parts are only available in SMD packages.

Smart Tweezers are an advanced multimeter tool specifically designed to test and troubleshoot SMD circuits. It automatically identifies resistors, capacitors, and inductors, and displays the relevant measurements. Advanced Devices sent us a pair of Smart Tweezers to review. We used them while building our last few SMD projects, read about our experience with this tool after the break.

Continue reading “Tools: Smart Tweezers” →

Parts: LTC2631A I2C Digital To Analog Converter

February 9, 2009 by 9 Comments

ltc2640

Linear Technology’s LTC2631A-LZ8 is an 8bit digital to analog converter (DAC) with an I2C interface. This DAC can output 255 different voltages, spaced evenly between 0 and 2.5volts. We previously demonstrated the LTC2640 with a three-wire SPI interface, but this version is controlled with only two signal wires.

Continue reading “Parts: LTC2631A I2C Digital To Analog Converter” →

Parts: AT Keyboard

January 26, 2009 by 15 Comments

atkeyboard

Last week we introduced a new version of the Bus Pirate universal serial interface tool. The last firmware update included an AT keyboard decoder library for both hardware versions.

There’s a ton of old AT keyboards making their way to the landfill. We’ll show you how to recycle one as an input device for your next project.

Continue reading “Parts: AT Keyboard” →

How-to: Prepare Your Eagle Designs For Manufacture

January 15, 2009 by 47 Comments

back

Cadsoft Eagle is a multi-platform freeware circuit layout program. Lots of open source hardware is designed in Eagle, and it’s become a hobbyist favorite. We use it for all of our hardware designs.

There are several ways to turn an Eagle design into an actual printed circuit board (PCB). We’ll show you how to save Eagle designs as industry-standard gerber files that are accepted by any PCB manufacturer. You can use the gerbers to order a single prototype, or a full panel.

Continue reading “How-to: Prepare Your Eagle Designs For Manufacture” →

Parts: Digital Proximity Sensor (Sharp GP2Y0D02)

January 5, 2009 by 19 Comments

[youtube=http://www.youtube.com/watch?v=TqOzmGNBgJE]

The GP2Y0D02 is an infrared proximity sensor with a detection field that extends 80cm. This type of sensor can be used to build collision avoidance systems for robots. We’ll demonstrate this sensor using a single resistor and a multimeter.

Continue reading “Parts: Digital Proximity Sensor (Sharp GP2Y0D02)” →