Monster Chess

June 14, 2010 by Jakob Griffith 24 Comments

Over 100,000 Lego pieces, 4 people a year to create, and a 12 foot by 12 foot chess board make this the largest most awesome Lego hack we’ve ever seen. Take that Lego Printer.

For a mere $30,000 you too can have such a setup. Not a lot of information is out yet, but we do know all the pieces are remote controlled via a PC with LabVIEW and a total of 38 NXT controllers are used. Oh, and of course you can see it live at the 2010 Brickworld. Check out a video of a replayed game after the jump.

[via Geekologie]

Continue reading “Monster Chess” →

LEGO Hand Controller

June 12, 2010 by Mike Szczys 12 Comments

[David Hyman] built this device to control a LEGO claw. One one end of things is the part you wear, that measures movement of two fingers and your thumb. On the other end of things is a LEGO claw with three opposing digits. You move, it moves. The claw uses light sensors and a gradient strip for position feedback. There is also an up-down wrist action that uses a touch sensor as the input. This is impressive enough to give the sniper rifle a run for its money.

[via Make]

Seven-six-two Millimeter. Full Plastic Jacket.

June 11, 2010 by Mike Szczys 31 Comments

Minifigs beware, something’s afoot. This LEGO sniper rifle is in talented hands to clean up those problem areas. [Jack Streat] put together this fascinating build as well as the delightful demo after the break. The bolt pulls a 1×4 block out of the eight-round magazine and loads it into the chamber. A pull of the trigger flings it with surprising accuracy. Want to be the coolest parent ever? Forgo the store-bought toys this year and put one of these together for your kid. Just don’t turn them into Private Pyle (NSFW).

Continue reading “Seven-six-two Millimeter. Full Plastic Jacket.” →

LEGO Printer Built Without NXT parts

June 2, 2010 by Mike Szczys 28 Comments

[youtube=http://www.youtube.com/watch?v=zX09WnGU6ZY]

[Squirrelfantasy] built a printer using LEGO pieces. It’s not a Mindstorm project but instead depends on some type of development board and some auxiliary components on a protoboard. We couldn’t get a good enough look to tell exactly what makes up the electronics so start the debate in the comments. We feel this is a printer and not a plotter because the stylus moves on just one plane while the paper feeds past it but that’s open for debate as well.

Guess this answers the question of why aren’t we building our own printers? Some folks are.

[Thanks Haxorflex and many others, via DVICE]

LEGO Pick And Place

May 31, 2010 by Mike Szczys 8 Comments

[youtube=http://www.youtube.com/watch?v=YoXCn4Gh_HA&w=470]

Turn your volume down and take a look at the brick sorting robot in the video above. It’s built using LEGO and powered by four different NXT modules. It sorts differently colored bricks on the intake conveyor and places them on three output conveyors. The build is solid and was [Chris Shepherd’s] impetus for starting a blog. We appreciate the pneumatic tricks that he detailed in some of his earlier posts such as a compressor, pressure switch, and air tank system. His advice is “build, build, build” and that’s what you’d have to do to perfect a monster of this size and scope.

Mindstorm Rubik’s Solver

April 29, 2010 by Mike Szczys 14 Comments

It has been quite a while since we looked in on the world of automated Rubik’s cube solving. [David Gilday] built this one using LEGO Mindstorm parts. It uses a computer to calculate the solutions but unlike the standalone Tilted Twister, this creation can solve more than one type of cube. As long as the physical dimensions are between 5 and 6 centimeters on a side, the machine can solve 2, 3, 4, and 5 piece cubes. [David] wasn’t quite satisfied with that though. He built a separate machine to take care of the 6x6x6 cubes too. See both in action after the break.

Want to see more? Don’t miss the CuBear solver developed at Berkeley or the AVR based solver.

Continue reading “Mindstorm Rubik’s Solver” →

Report From ESC Silicon Valley 2010

April 28, 2010 by Phil Burgess 10 Comments

Ah, the heady aroma of damp engineers! It’s raining in Silicon Valley, where the 2010 Embedded Systems Conference is getting off the ground at San Jose’s McEnery Convention Center.

ESC is primarily an industry event. In the past there’s been some lighter fare such as Parallax, Inc. representing the hobbyist market and giant robot giraffes walking the expo. With the economy now turned sour, the show floor lately is just a bit smaller and the focus more businesslike. Still, nestled between components intended to sell by the millions and oscilloscopes costing more than some cars, one can still find a few nifty technology products well within the budget of most Hack a Day readers, along with a few good classic hacks and tech demos…

Continue reading “Report From ESC Silicon Valley 2010” →