The Many Reasons For Putting Microphones In Rainforests

November 30, 2024 by Maya Posch 8 Comments

If a tree falls in a forest with nobody around, does it make a noise? In the case of the rainforests equipped with the Rainforest Connection’s Guardian system someone most assuredly will.

Rainforest Connection’s Guardian system up close, with microphone visible. (Credit: RFCx)

Originally created by the people behind the US nonprofit Rainforest Connection (RFCx) using upcycled smartphones to detect the sounds of illegal logging, their project now has grown into something much larger, keeping not only tabs on sounds of illegal activity, but also performing bioacoustic monitoring for scientific purposes.

Currently active in ten countries, the so-called Guardian Platform no longer features smartphones, but custom hardware inside an IP66 weatherproof enclosure and a whole range of communication options, ranging from cellular bands to satellite communications. The petal-shaped solar panels provide the module with up to 30 watts of power, and double as a shield to help protect it from the elements.

Not only is the real-time microphone data incredibly useful for rangers trying to stop illegal logging, it also provides researchers access to countless hours of audio data, which will require detailed, automated analysis. Even better is that if the audio data is available to the general public as well, via their Android & iOS apps (bottom of page), just in case you wanted to hear what that sneaky wildlife in the jungle of Peru is up to right now.

Building A Miniature Rainbow Sand Table

November 30, 2024 by Lewin Day 10 Comments

Sure is coarse and rough and irritating, and it gets everywhere. But it can also be beautiful — drag a small ball through it in a controlled manner you can make some really pretty patterns. That’s precisely what this compact build from [Printerforge] does.

The build relies on an ESP32 as the brains of the operation. It employs small 28BYJ-48 motors to run the motion platform. These were chosen as they operate on 5 V, simplifying the build by allowing everything to run off a single power supply. Along with a bunch of 3D printed parts, the motors are assembled into motion system with linear rods and belts in a CoreXY layout, chosen for speed and precision. It’s charged with moving a small magnet to drag a ball bearing through the sand to draw patterns under the command of G-code generated with the Sandify tool.

We’ve seen some great sand table builds over the years. Some use polar coordinate systems, while others repurpose bits of 3D printers. If you’ve got a creative new way of doing it, don’t hesitate to let us know!

Modernizing An Apple IPod, Or: A Modern-Day Ship Of Theseus

November 29, 2024 by Maya Posch 24 Comments

Back in the day the Apple iPod was the personal music player (PMP) to get even if mostly because everyone and their dogs had one. These days most people just use their smartphone as a PMP, but what if you were to take, say, a 5th generation iPod and modernized it? That was the basic idea that [Zac Builds] picked up and ran with, with the results as shown in the video he made about it.

The 5th gen iPod was the first one capable of playing video, and was released in October of 2005. Powering it is a Broadcom BCM2722 for video playback, and came with a 30 or 60 GB HDD. First thing that [Zac] tosses is the old (3.7V, 650 mAh) battery, which appears to be already a replacement for the original, followed by the 60 GB 1.8″ HDD. Next tossed is the 2.5″ 320×240 QVGA screen, which gets replaced by a compatible modern LCD. The case is replaced with a transparent case, along with a transparent touch wheel, and the HDD is replaced with a 256 GB SD card in an iFlash Solo SD card adapter for iPods.

Next up was the installation of more off-the-shelf mods, such as a ‘taptic mod’ – which adds a rumble motor – and replacing the iPod’s 30-pin connector with a USB-C connector, requiring some fiddly soldering and desoldering. Following this a Bluetooth audio transmitter was added, extreme PCB mods performed with a cut-off wheel to make everything fit with a custom midframe and rear case.

Ultimately, the parts left of the original iPod were most of the mainboard and some flex cable, which raises the question of whether it might not have been faster and easier to start off with designing a custom PCB. Perhaps the true value is in the modding journey and not the destination?

Thanks to [Keith Olson] for the tip.

Continue reading “Modernizing An Apple IPod, Or: A Modern-Day Ship Of Theseus” →

A researcher in a safety harness pollinates an American chestnut tree from a lift. Another researcher is on the other side of the lift and appears to be taking notes. The tree has bags over some of its branches, presumably to control the pollen that gets in. The lift has a grey platform and orange arm.

Hacking Trees To Bring Back The American Chestnut

November 29, 2024 by Navarre Bartz 36 Comments

“Chestnuts Roasting on an Open Fire” is playing on the radio now in the Northern Hemisphere which begs the question, “What happened to the American chestnut?” Would you be surprised to hear there’s a group dedicated to bringing it back from “functional extinction?” [via Inhabitat]

Between logging and the introduction of chestnut blight, the once prevalent American chestnut became increasingly uncommon throughout its traditional range in the Appalachians. While many trees in the southern range were killed by Phytophthora root rot (PRR), the chestnut blight leaves roots intact, so many chestnuts have been surviving by growing back from the roots only to succumb to the blight and be reborn again. Now, scientists are using a combination of techniques to develop blight-resistant trees from this remaining population.

The American Chestnut Foundation recognizes you can’t improve what you can’t measure and uses a combination of “small stem assays (SSAs) performed on potted seedlings, improved phenotype scoring methods for field-grown trees, and the use of genomic prediction models for scoring resistance based on genotype.” This allows them to more rapidly screen varieties for blight resistance to further their efforts. One approach is based on conventional plant breeding techniques and has been crossing blight and PRR-resistant Chinese chestnuts with the American type. PRR resistance has been found to be less genetically complicated, so progress has been faster on resistance to that particular problem. Continue reading “Hacking Trees To Bring Back The American Chestnut” →

Swapping Batteries Has Never Looked This Cool

November 29, 2024 by Donald Papp 39 Comments

We don’t know much more than what we see with [Kounotori_DIY]’s battery loader design (video embedded below) but it just looks so cool we had to share. Watch it in action, it’ll explain itself.

Before 3D printers made it onto hobbyist workbenches, prototyping something like this would have been much more work.

[Kounotori_DIY] uses a small plastic linear guide as an interface for an 18650 battery holder and as you can see, it’s pretty slick. A little cylindrical container slides out of the assembly, allowing a spent cell to drop out. Loading a freshly charged cell consists of just popping a new one into the cylinder, then snapping it closed. The electrical connection is made by two springy metal tabs on either end that fit into guides in the cylindrical holder.

It’s just a prototype right now, and [Kounotori_DIY] admits that the assembly is still a bit big and there’s no solid retention — a good bump will pop the battery out — but we think this is onto something. We can’t help but imagine how swapping batteries in such style with a nice solid click would go very nicely on a cyberdeck build.

It’s not every day that someone tries to re-imagine a battery holder, let alone with such style. Any ideas how it could be improved? Have your own ideas about reimagining how batteries are handled? Let us know in the comments!

Continue reading “Swapping Batteries Has Never Looked This Cool” →

Simple Pen Plotter Rolls On The Table

November 29, 2024 by Lewin Day 6 Comments

Pen plotters are popular builds amongst DIY CNC enthusiasts. They’re a great way to learn the fundamentals of motion control and make something useful along the way. In that vein, [Maker101] has created a neat barebones plotter for tabletop use.

The basic design relies on familiar components. It uses a pair of MGN15 linear rails as the basis of the motion platform, along with NEMA 17 stepper motors to run the X and Y axes. These are assembled with the aid of 3D-printed parts that bring the whole frame together, along with a pen lifter operated with a hobby servo.

The neat thing about the design is that the barebones machine is designed to sit upon an existing tabletop. This eliminates the need to integrate a large flat work surface into the plotter itself. Instead, the X axis just runs along whatever surface you place it on, rolling on a small wheel. It’s likely not ideal for accuracy or performance; we could see the machine itself skating around if run too fast. For a lightweight barebones plotter, though, it works well enough.

If you dig building plotters, you might like to step up to something more laser-y in future. Video after the break.

Continue reading “Simple Pen Plotter Rolls On The Table” →