New Term For Art: Sculptural Robotics

[Dan Roe] has been working on Sculptural Robotics for quite some time, and most recently presented his newest creation: Solar Flowers 2010. Typically, Sculptural Robotics (coined by [Dan] himself) are stand alone, static art presentations made from electronic components and wire. [Dan] of course has taken it quite a bit further; giving all his sculptures life using solar panels, motors, engine circuits, and more. Making them zero emission, and beautiful at the same time. You can catch four videos after the jump of his moving sculptures. Not that we’re picking favorites, but the dragonfly is pretty amazing if we do say so ourselves.

Continue reading “New Term For Art: Sculptural Robotics” →

Homebrew Firmware Upgrade For VCI-100 Turntable Controller

We love hacks that take quality products and make them better. This enhanced firmware for the VCI-100 is a great example of that. In a similar fashion as the Behringer hack, [DaveX] reverse engineer the firmware for the device and figured out a few ways to make it better. It improves the scratch controller and slider accuracy to use 9-bit accuracy from the ADC readings, which in the stock version were being shifted down to 7-bits. There’s also a few LED tricks they call Disco Mode. They’re selling a “chip” that you need to flash the firmware but from what we can see it’s simply an RS232 converter so you might be able to figure out how to work without that part. We’ve embedded a demo of firmware version 1.4 after the break.

Continue reading “Homebrew Firmware Upgrade For VCI-100 Turntable Controller” →

Motorcycle Rear-view With In-helmet Display

Want to see what’s behind you when riding your sport bike without taking your eyes off the road? They make rear view cameras for that but [Nescioqd] wanted a rear display right in his helmet (PDF). He started by mounting a rear-pointing camera on the back of the bike, powered from the 12V feed for the taillight. On the display side of things he picked up a Myvu Crystal wearable display. This is like a pair of glasses that have small LCD screens were the lenses should be. [Nescioqd] removed one lens and mounted it inside the helmet.

Since the display resides inside the helmet there is some concern about being able to see at night with a bright screen below your eyeball. [Nescioqd] actually ran into the opposite problem at first, bright sunlight makes it difficult to see the image on the LCD screen. He fixed this by picking up a dark tinted helmet visor (the easiest solution) but we’d love to see a photoresistor used to regulate the backlight level.

It would be interesting to see both screens used, with rear-view on one side and an instrument display on the other.

Audio Cabinet Refit With Modern Equipment

Hard at work on making this 1960’s Fleetwood audio console usable again, [Travis] packed a lot of power into the retro case. Both the radio and turn table had stopped working but the cabinet looks great and the speakers still work. In the lower center cavity you’ll now find a full computer motherboard and replacement amplifier. A new turntable has been added with an interesting vibration-dampening shelf to support it. [Travis] built the shelf with a void in between two layers of wood which he filled with sand to help with isolation. The remote control for the amp also needed some work as the receiver is pointed to the back of the unit. To fix that a second IR receiver found a home behind the fabric for one of the speaker grates. That receiver is monitored by an ATmega168 microcontroller and signals are repeated back to an IR LED mounted near the amplifier.

Beefing Up A Cheap Drill Motor

[Rob] just finished reinforcing a cheap drill motor. He picked up the tool at Harbor Freight and ditched the case. The plastic retaining ring was replaced with a thick metal washer which he machine The washer uses three bolts to attach to the mounting plate that he welded together. We’re not exactly sure what he’s got in mind as he only mentioned that this will be used with a robot. We wouldn’t mind having one of these as a bench motor but there must be hundreds of uses now that it can be attached to just about anything. It seems Harbor Freight has become popular as hacking’s raw material source. The last example we saw of this was a welding table made from a utility cart.

Hackaday Links: September 19, 2010

6502 Gate Simulator

Ever wondered what’s going on inside that chip as the program executes? Now you can take a look at the die itself with this visual gate simulator for the 6502 processor. [Thanks Puli and Svofski]

Copper corrosion

[Moogle] cracked open his DockStar to find corroded copper. It seems that Seagate left a portion of the ground plane unprotected and it reacted badly with the shielding metal. If you have one of these devices you might want to crack it open and tin the exposed copper so that it will hold up over time.

Segway kickstand

Don’t want your Segway to flop over when you park it? Follow [Paul’s] lead in building a kickstand for the self-balancer. You can just make it out in the image above. It’s a dumbell that folds down from the handlebar tube when you’re not on board.

Tesla makes everything better

Do you like the song Iron Man? We think it’s better when our friend Nikola takes part.

No Smoking

Smoking is really quite bad for you. Plus you can’t chain smoke nearly as efficiently as this mechanical smoking machine can so don’t even try. [Thanks Ferdinand]