Snow skiing looks easy, right? You just stay standing, and gravity does the work. The reality is that skiing is difficult for beginners to learn. [19mkarpawich] loves to ski, but he was frustrated seeing crying kids on skis along with screaming parents trying to coach them. Inspired by wearable electronics, he took an Arduino, an old jacket, some LEDs, and created Ski Buddy.
Continue reading “Ski Buddy Jacket Uses Arduino To Teach Youngsters To Ski”
If you’ve ever known anyone who has to monitor their blood glucose level, you know it is annoying to have to prick your finger with a lancet to draw blood for each measurement. A new sweatband that incorporates flexible electronics can measure glucose–as well as sodium, potassium, and lactate–from your sweat, without a painful pin prick.
[陳亮] (Chen Liang) is in the middle of building the ultimate ring watch. This thing is way cooler than the cheap stretchy one I had in the early 1990s–it’s digital, see-through, and it probably won’t turn [陳]’s finger green.
The current iteration is complete and builds upon his previous Arduino-driven watch building experiences. It runs on an ATtiny85 and displays the time, temperature, and battery status on an OLED. While this is a fairly a simple build on paper, it’s the Lilliputian implementation that makes it fantastic.
[陳] had to of course account for building along a continuous curve, which means that the modules of the watch must be on separate boards. They sit between the screw bosses of the horseshoe-shaped 3D-printed watch body, connected together with magnet wire. [陳] even rolled his own coin cell battery terminals by cutting and doubling over the thin metal bus from a length of bare DuPont connector.
If you’re into open source watches but prefer to wear them on your wrist, check out this PIC32 smart watch or the Microduino-based OSWatch.
We’re not sure that [Alec]’s dad actually requested remote-controlled eyebrows for his birthday, but it looks like it’s what he got! As [Alec] points out, his father does have very expressive eyebrows, and who knows, he could be tired of raising and lowering them by himself. So maybe this is a good thing? But to us, it still looks a tiny bit Clockwork Orange. But we’re not here to pass judgement or discuss matters of free will. On to the project. (And the video, below the break.)
An ATmega328 (otherwise known as cheap Cloneduino Alec wrote that the 328 was from a real Arduino) is trained to run motors in response to IR signals. An L293D and a couple of gear motors take care of the rest. Sewing bobbins and thread connect the motors to the eyebrows. And while it’s not entirely visible in the photo, and veers back into not-sure-we’d-do-this-at-home, a toothpick serves as an anchor for the thread and tape, secured just underneath the ‘brows for maximum traction.
We have to say, we initially thought it was going to be a high-voltage muscle-control hack, and we were relieved that it wasn’t.
Continue reading “Remote-Controlled Eyebrows For Your Birthday”
Comedian Steven Wright used to say (in his monotone way):
“We lived in a house that ran on static electricity. If we wanted to cook something, we had to take a sweater off real quick. If we wanted to run a blender, we had to rub balloons on our head.”
Turns out, all you need to generate a little electricity is some paper, Teflon tape and a pencil. A team from EPFL, working with researchers at the University of Tokyo, presented just such a device at a MEMS conference. (And check out their video, below the break.)
Travel around to enough security conferences, faires, and festivals, and you’ll see some crazy wearable electronics. Most of them blink, and most of them use LEDs. Electroluminescent panels are used for wearables, but that’s a niche – the panels are a little expensive, and you have to deal with high frequency AC instead of the much simpler, ‘plug in a LiPo here’ circuit LED-based wearables have to contend with.
Still, electroluminescent panels are cool, and thanks to how EL panels are made, you can screen print EL displays. That’s what some of the guys at AMBRO Manufacturing did recently: screen printing electroluminescent lights directly onto garments. It’s t-shirts from Tron made real.
EL panels and EL wire are really only three separate parts: a conductor of some sort, a phosphor, and another conductor. Pass a high-frequency AC current through the conductors, and the phosphor lights up. With EL wire, it’s a thick copper wire clad in phosphor and wrapped in a very fine copper wire. EL displays are made with conductive ITO-coated glass or plastic. It’s a relatively simple construction, and one that is perfectly suited for screen printing. In fact, one of the first EL displays – the DSKY, the user interface for the Apollo Guidance Computer – used screen printed seven-segment EL displays.
The folks at AMBRO only have a proof of concept right now, but it is a completely screen printed electroluminescent design on fabric. To light it up, the t-shirt will need an inverter, but this is the beginnings of t-shirts from Tron.
Video below.
Continue reading “Screen Printing Electroluminescent T-Shirts From Tron”
A proper smartwatch can cost quite a bit of money. However, there are some cheap Bluetooth-connected watches that offer basic functions like show your incoming calls, dial numbers and display the state of your phone battery. Not much, but these watches often sell for under $20, so you shouldn’t expect too much.
Because they’re so cheap, [Lee] bought one of these (a U8Plus) and within an hour he had the case opened up and his camera ready. As you might expect, the biggest piece within was the rechargeable battery. A MediaTek MT6261 system on a chip provides the smart part of the watch.
