Incredible 1000 MW Iron Man Repulsor Beam

July 14, 2011 by Mike Nathan 55 Comments

awesome_hand_mounted_repulsor_laser

German lab technician by day, hacker by night [Patrick Priebe] has done it again, this time strapping a ridiculously high-powered laser to the palm of his hand. Earlier this year, we showed you an awesome Neodymium:YAG pulse laser pistol he built, and it seems he never takes a rest from constructing crazy laser projects.

[Patrick] is a huge Iron Man fan, and his palm-mounted laser unit was built as an ode to his all-time favorite super hero. Crafted to invoke images of Iron Man’s repulsor beam, his laser uses a 1000 mw 445 nm laser diode to get the job done. if you happen to be keeping track, that makes his DIY laser just as powerful as the WickedLasers Spyder 3 Arctic – THE benchmark in portable handheld lasers.

Like his previous builds, we can’t seem to find a whole lot of information about the laser’s construction process. We do know however, that the unit was crafted from a 2mm thick sheet of brass, which fits nicely on his hand while simultaneously acting as a very large heat sink. This large surface area allows him to run the laser continuously for three minutes before requiring a cool down, which is no small feat.

We think it’s an awesome project, and as you can see by the videos of the three separate revisions it has undergone, [Patrick] is quite serious when it comes to perfecting his wares.

Continue reading “Incredible 1000 MW Iron Man Repulsor Beam” →

DIY Wiper Speed Control And Collision Avoidance

July 13, 2011 by Mike Nathan 24 Comments

ir_sensor_rain_detection

On many new cars, automatic wiper speed control can be had as an upgrade, though most cars do not offer front-end collision prevention at all. [Rishi Hora] and [Diwakar Labh], students at the Guru Tegh Bahadur Institute of Technology in New Delhi, developed their own version of these features, (PDF warning, skip to page 20) which they entered into last year’s Texas Instruments Analog Design Contest. Under the guidance of professors [Gurmeet Singh] and [Pawan Kumar], the pair built the systems using easily obtainable parts, including of course, an MSP430 microcontroller from TI.

The collision prevention system uses a laser emitter and an optical detector to estimate the distance between your car and the vehicle in front of you, sounding an alarm if you are getting too close. In a somewhat similar fashion, the wiper speed control system uses an IR emitter and detector pair to estimate the amount of water built up on the windshield, triggering the wipers when necessary.

While not groundbreaking, the systems would be quite handy during monsoon season in India, and seem easy enough to install in an older vehicle. The only thing we’re not so sure about is pointing lasers at cars in traffic, but there are quite a few available alternatives that can be used to measure distance.

Continue reading to see a video walkthrough and demonstration of both systems.

Continue reading “DIY Wiper Speed Control And Collision Avoidance” →

How To Build Your Own Pulsed Laser Pistol

July 10, 2011 by Mike Nathan 50 Comments

build_your_own_pulsed_laser_gun

Self-declared Mad Scientist and Instructables user [Trevor Nestor] recently built a pulse laser pistol and decided to share his build process, so that you too can build a ray gun at home. The gun is made up of mostly scavenged components, save for the Neodymium:YAG laser head, which he purchased on eBay for about $100. He does say however, that you can score an SSY-1 laser from an old rangefinder, providing you hang out near a stockpile of decommissioned Abrams tanks.

[Trevor] walks you through the process of recycling old disposable cameras to get enough components for a capacitor bank, as well as how the charging circuit should be constructed. He also discusses how the laser head needs to be wired, before showing off the finished laser pistol in a cheeky video, embedded below.

While the gun lacks the finish of this laser pistol we showed you, it’s no less potent when shooting through plastics, wood, and thin metals. It’s a great starting point if you are looking to build a laser of your own, leaving room for improvements, such as a faster charging circuit.

Continue reading “How To Build Your Own Pulsed Laser Pistol” →

Making Airsoft Guns Far More Potent

June 21, 2011 by Mike Nathan 27 Comments

airsoft_laser_rifle

[Drake] wrote in to share his recent project, which involves repurposing an Airsoft rifle that was sitting around, collecting dust. Airsoft guns as a whole are not all that impressive, but convert your Airsoft gun into a laser rifle, and we’re all ears.

His laser blaster is honestly pretty straightforward as far as laser projects go, but we just couldn’t resist. He pulled apart the Airsoft gun, removing all of the “airy” bits, leaving just the trigger behind. He added a 9v battery and a linear power supply to the gun, wiring them up to a 700mW laser diode from what we hope was a broken Blu-ray burner.

In the obligatory “look at what I can destroy with my laser gun” video embedded below, [Drake] shows off his gun’s potency at various ranges, popping balloons from 35 feet away. He even shows off the laser’s usefulness as a light pen for glow in the dark surfaces.

While his modifications are nothing we haven’t seen before, his gun is far more accessible than others we have featured.

Have any cool high-powered laser projects of your own? Share them with us in the comments.

Continue reading “Making Airsoft Guns Far More Potent” →

The Laser Guided Wheelchair

June 2, 2011 by Jeremy Cook 10 Comments

Using a scanning laser similar to those used in industrial safety systems, a new wheelchair developed by Sweden’s Luleå University of Technology allows those who are visually impaired to drive it without assistance. A driver is given haptic feedback as a navigation aid, reportedly similar to using a cane.

Although something like this is good in concept, this idea is already a working prototype. Doctoral student Daniel Innala Ahlmark (who is visually impaired himself) has already taken this wheelchair on a test run in his university’s busy Computer Science, Electrical, and Space Engineering Department. After this test run he remarked that he “felt safe like using a white cane.”

It’s really neat to see engineering and hacking skills put to use to help people who are impaired in some way (even cooler to see someone visually impaired helping with the process itself!). For more “hacks” related to helping people check out this brain controlled wheelchair, or this mobility device for kids.

Hackaday Links: Monday, May 30th

May 30, 2011 by Mike Nathan 5 Comments

Huge, fully functional NES game pad replica

huge_nes_pad

Students at Dutch TU Delft university recently built a huge replica of the original NES controller (Google Translation), which is fully functional and can be used to play games on a large display screen they also installed. How big is it, you ask? It’s about 6 meters wide – over 30 times the size of the original NES game pad and requires participants to jump on the buttons to play.

Convert any image to G-code

bitmap_to_gcode

Members of [Forskningsavdelningen], a Swedish hackerspace, are working on software that will allow users to vectorize bitmap images in order to convert them to G-code files for CNC milling. A good portion of the project is complete, but there is still a bit of work to do, so you won’t see it in action for a while. When it’s ready, we’ll be sure to let you know.

Convert your lame Dead Space plasma cutter into a bonafide laser weapon

dead_space_laser

If you forked out big bucks for the special edition of Dead Space 2, you know how lame the included plasma cutter replica is. Check out this video, that shows you how to convert your LED toy to a dual laser, fire starting, laser pistol. The process is pretty simple, so what are you waiting for?

Synchronized, LED-lit juggling balls

led_balls

[Jonathan] wrote in to share a project he and some friends have just finished. He’s not sharing a ton of details at the moment, but he has put up a video showing off their wireless LED juggling balls. All we know is that they use bright RGB LEDS, Zigbees for communication, and that they are awesome. We can’t wait to hear more about them!

Water cooled PS3 Laptop

watercooled_ps3

[Pirate] recently unveiled his latest work, a water-cooled Playstation 3 laptop. It looks pretty sharp, and can undoubtedly rival some of Ben Heck’s work, even if it does have an external PSU. Obviously having a separate power component isn’t necessarily ideal, but when you are cramming all of that water cooling goodness into such a small package, something has to give!

BAMF2011: Lasersaur Is One BIG Laser Cutter!

May 22, 2011 by Phil Burgess 38 Comments

Psst…wanna buy a laser cutter, but not ready to sell your internal organs? Nortd Labs’ Lasersaur project aims to create an open source large-format laser cutter/engraver that undercuts (har har!) the cost of commercial models by an order of magnitude.

Continue reading “BAMF2011: Lasersaur Is One BIG Laser Cutter!” →