Scale Model Of A Civil War Mortar Shoots Steel Golf Balls

July 31, 2012 by Mike Szczys 27 Comments

[Sir Keyboard Commando] just emerged from his machine shop to show off the 1/6th scale model of a Civil War mortar which he recently finished fabricating. It started with some bar stock that measured four inches in diameter and accepts steel balls the size of golf balls as ammunition.

The bore diameter is 1.725″ which gives just a bit of clearance for the 1.685″ golf ball specs. Each of the steel balls weighs in at just over 11 ounces. You get a really good look at the finished mortar in this test-fire video. It’s quite small but [Sir Keyboard Commando] reports that the full assembled unit still weighs in at a whopping forty pounds.

This certainly isn’t an improvised weapon, but we’re quite surprised to see it being test fired. We’d bet it turns some heads that the local firing range.

[via Reddit]

Developing A Better Way To Control 10,000 LEDs

July 31, 2012 by Mike Szczys 14 Comments

The SoundPuddle project drives thousands of LEDs based on audio input. The team is working on a replacing the controller for this wire-filled setup with something more robust. They took the mess seen above to the Apogaea Festival and were plagued by loose wires and unreliable communications due to noise and interference. The aim of the new system is to reliably control up to 10,000 LEDs.

The red PCB seen at the center of the rats-nest is a Papilio FPGA board. They still want to use it to drive the installation, but a new hardware interface is necessary. The solution is to design what they call a megawing (wings are to Papilio as shields are to Arduino). The LEDs will be in RGB strip form, so one of the requirements is to supply enough connectors to drive 16 channels of SPI devices. The wing will also include the 48V power source and connectors for the condenser microphone that serves as an input for the SoundPuddle. There are also two other options for audio input, one via a Bluetooth module (which can double as a control device) and the other via MIDI.

After the break you can see a lighting demo. Be ready with the volume controls as most of the sounds used in the test are quite annoying.

Continue reading “Developing A Better Way To Control 10,000 LEDs” →

Mouth-powered Tools That Will Make Your Dentist Cringe

July 31, 2012 by Mike Szczys 25 Comments

Want to try your luck drilling out a PCB with this mouth-powered drill? [Cheng Guo] shows off one of his many mouth-powered tools above. It’s a tiny drill which spins with the opening and closing of your jaw. The concept may seem a bit silly, but his ability to fabricate these machines is fantastic.

The clip after the break starts off with the drilling demo seen above. From there he shows off several different tools. One is a molding machine that uses your breathing to spin a mold, thereby forcing the material inside to conform to its shape. There’s also a wood lathe. You hold the cutting tool in the your mouth and spin the mechanism with a bow and string setup. If you’re good at sucking, his vacuum former is right up your alley. Just heat up the plastic stock in the microwave and suck with all your might. Finally he shows off an extruder. We’re not quite sure how that one works.

Continue reading “Mouth-powered Tools That Will Make Your Dentist Cringe” →

Control Everything In Your Car With The Car Kracker

July 31, 2012 by Brian Benchoff 47 Comments

If your whip is a Honda, Toyota, BMW, Chrysler, VW, or Mini made in the last decade or so, the Car Kracker is for you. This project allows you to connect directly to your car’s computer system, allowing you to display messages on your stereo, play music off an SD card, and even override factory settings like always-on daytime running lights.

The Car Kracker uses ISO 9141, an in-car communications protocol that is now mostly used in foreign (for the US) cars. The build uses a Gadget Gangster Propeller board to connect to the CD changer port and OBD-2 port in the trunk, and the diagnostic port located under the hood.

With the Car Kracker, it’s easy to connect the Aux In on your stereo to an SD card loaded with music, or even plug in an iPod for the poor souls without a 1/8″ jack. Dealer customizations such as turning the ‘door is ajar’ noise off, toggling daytime running lights, and throwing a nav warning up are also possible.

Check out the two videos after the break, and if anyone has any more info on getting this deep into a car’s computer system (a wiki, maybe?), send a link in on the tip line.

Continue reading “Control Everything In Your Car With The Car Kracker” →

A Large Hexapod Made Of Wood And PVC Pipe

July 31, 2012 by Jeremy Cook 7 Comments

Although not the biggest hexapod walker we’ve seen by any means, this one is nonetheless worth a mention. Made with windshield wiper motors, PVC pipe, and lots of wood, it’s still a good size ‘bot. It’s a work in progress, but check out the video of it’s legs being tested as well as one of it’s preliminary assembly after the break.

Control is similar to this little hexapod that we’ve featured before in the the front and back legs are driven by a motor and linked together using threaded rod. In this case though, the rod is 1/4 – 20, much larger than the 4-40 rod used by it’s little predecessor. Also unlike little PegLeg, the middle legs are independently actuated, not linked together. This should allow for some different modes of locomotion.

Different modes of locomotion, that is, if it’s able to walk. Although able to pick itself up, the middle legs are barely strong enough to support the large battery and powerful, but heavy, automotive motors. This is an introductory post to this project, and everything will hopefully be worked out and explained in time. Be sure to check back and see how this robot progresses, and the details of the different elements of this ‘bot. Continue reading “A Large Hexapod Made Of Wood And PVC Pipe” →

Automated Turret Gives You The Upper Hand In Office Warfare

July 31, 2012 by Mike Nathan 17 Comments

TI-office-turret

When your co-workers get on your nerves, the mature recourse is to be the bigger person and simply ignore the obnoxious individual. A team of engineers from TI show us a slightly alternative means of dealing with office mates which is not quite as mature, though far more entertaining.

The office toy cum mechanized weapons system relies on a TI MSP430 LaunchPad, coupled with a custom Turret430 breakout board. The former is the brains of the operation, while the latter houses motor drivers for the motorized turret. The system can be steered throughout its 300 degree range of rotation using an attached joystick, but in the interest of catching their target by surprise, they added an automated mode as well. The automated targeting system uses an attached webcam to pick out victims by the color of their clothing, which seems to work pretty well.

To see the system in action, check out the video embedded below.

Continue reading “Automated Turret Gives You The Upper Hand In Office Warfare” →

Ping Pong Ball Barrage

July 30, 2012 by Mike Szczys 21 Comments

What should you do with your down time between sophomore and junior year at MIT? You better build something awesome. [Christian Reed] didn’t disappoint with his newest creation. He calls it the Ping Pong Mauler and we think that’s an appropriate name. It doesn’t just lunch a ball, it belches forth a relentless barrage.

He certainly has no shortage of ammo. A few garbage bags full of the white orbs number at least 3000 strong, and the plastic drum he’s using as a hopper has room for them all. Jamming is an issue and in the image above you can see him working the agitator with his right hand to prevent a clog. The system is mobile, but the shop vacuum used to propel the balls needs AC power. This means there is a tether that keeps it from roaming too far from home. [Christian] included an air tank in the design but apparently the pressurized air doesn’t do much to help with launch speed. That’s good because pressurized ball guns can be scary.

Check out the video after the break to see the ping pongs fly. We bet they’ll be mowing over some strays out in the yard for at least the rest of this summer.

Continue reading “Ping Pong Ball Barrage” →