Laser Raygun Boasts 300mW, Hunts Klingons

October 18, 2009 by Mike Szczys 39 Comments

Phasers come with two settings: stun and kill. [Luke] took this seriously when he put two Blu-ray lasers into a toy raygun. He picked up the toy from Amazon for about twenty bucks and set to work.

The laser diodes are both pulled out of a 6x BD-R burner, which we think is a pretty expensive source to scavenge from. [Luke] removed the toy circuitry, reusing the trigger, top switch, and battery pack. The two diodes are mounted on a swiveling carriage which is turned 180 degrees to switch between the two diodes. A boost driver converts the 3v from the batteries up to 7v for the diodes.

This is a skillful conversion and [Luke] should be proud. Don’t miss the video after the break and if you’re thirsty for more take a look at the last hand held laser we featured.

Continue reading “Laser Raygun Boasts 300mW, Hunts Klingons” →

Underwater Laser, Just Add Shark

October 12, 2009 by Mike Szczys 30 Comments

underwater-laser-beam

[iskor12] put together a blu-ray laser that is waterproof and packs quite a punch. At 182 mW there is enough power here to pop dark colored balloons (see the video after the break). To make this happen, he found an LED flashlight that has rubber o-rings for waterproofing. Although small, there is enough space in the case to house the battery, driver, and laser diode. A thick ring of aluminum is placed around the laser diode to act as heat sink.

We’ll admit, we don’t know that much about lasers. This is probably the wrong question to ask, but now that he has this what do you do with it? Leave us a comment about your plans for this diabolical creation.

Continue reading “Underwater Laser, Just Add Shark” →

Five Concept Mice Add Multi-touch Control

October 6, 2009 by Mike Szczys 34 Comments

[youtube=http://www.youtube.com/watch?v=SLw1MXTDlAE]

Microsoft is showing off five concepts for added mouse functionality. All of them seek to replace traditional move-and-click with touch sensitivity through either capacitive sensing, video recognition, sensor articulation, or laser scanning. We’re excited about the prospects of some of these features but at the same time wonder what this does to the price of this much-abused peripheral. After the break we’ll touch on each of the devices, along with time references for the video embedded above. Continue reading “Five Concept Mice Add Multi-touch Control” →

RGB Laser

October 4, 2009 by Jakob Griffith 22 Comments

laser_RGB_21_big

Last month we had the pleasure of bringing you [FireMyLaser’s] green laser spirograph. Just green is great for a while, but why not add red and blue for a full spectrum of color! [c4r0] steps in at this point to bring us his red green blue laser.

(Editor’s note: the old forum doesn’t seem to exist in 2023, but the project moved here. Thanks, [Rolson]!)

He dug around inside Blu-ray players and DVD drives until he had a collection of lasers, refractors, and other filters that fit his needs. With some careful toothpick alignment and glue, his setup was complete.

But then he went further by modified his galvo scanner to accept the RGB laser; requiring a custom circuit board and new software, both available on his site. The original is in Polish, but Google does a decent translation. Check after the jump for a video.

Continue reading “RGB Laser” →

Laser Triggered Photography

September 30, 2009 by Jakob Griffith 9 Comments

FFU0B63FZG43RK5.MEDIUM

Popped balloons or bullets fired into apples, anyone can photograph with a quick sound based camera rig. Lasers have been used forever in motion detection. And even door bell chimes have been used before for remote camera shutter releases. No, [SaskView] wanted to go further and created his Laser Triggered High-Speed Photography setup, to photograph (of all things) milk splashes. We liked the simplicity of the project however; requiring no programmed microchips or overly complicated circuitry – rather he took a quick trip to the local dollar shop, used the amazing CHDK firmware, and he produced perfect results every time.

[Update: CHDK, not CHKD firmware. My mind must be elsewhere. Thanks jbot and agent smith]

Pinch Control2: Laser Drawing

September 28, 2009 by Caleb Kraft 4 Comments

[youtube=http://www.youtube.com/watch?v=0uXIqQxarYI]

[atduskgreg] posted this cool looking rig. That’s a batting glove, chopped up and equipped with a flex sensor and a pressure sensor. The end goal was to create a new method of drawing. You can see he’s interfaced with the servos decently. It seems fairly responsive and intuitive. Looking at his results though, make us wonder if all that effort was worth it. We would probably apply this rig to some kind of animatronics.

Wacom Light Graffiti

September 20, 2009 by Mike Szczys 17 Comments

wacom_light_graffiti

[Jon] wanted to have some fun with the Graffiti Research Lab’s LASER Tag. Unfortunately his computer wasn’t quite up for the challenge of detecting the laser pointer with a webcam. Not to be discouraged by this hardware limitation, he purchased a used Wacom tablet and threw together some code to make it work with the GRL display software. Now designs can be scrawled on the pad and the projector displays them with the familiar dripping paint effect. Continue reading “Wacom Light Graffiti” →