3G Connected Hotspot Hangs Out At Your House

October 31, 2011 by Mike Szczys 22 Comments

[Drug123] made the most out of this inconspicuous gray box on the gable end of his father’s home. It serves up a 3G Internet connection that was otherwise unavailable..

The project idea was sparked by the absence of wired or fiber optic broadband in the community where his dad lives. He knew some neighbors were using 3G connections, but he couldn’t get it to work inside the house. So he set about developing an external installation that would both communicate with the cellular network, and provide a WiFi connect to it. Hardware for that is relatively expensive; a USB 3G modem and a WiFi router with a USB port.

The box itself is made of plastic, but even without the Faraday cage effect that would have been formed by using a metal housing, the 3G modem’s internal antenna just doesn’t do the job. You can see that [Drug123’s] solution was an external antenna which is mounted at the peak of the roofline. Inside the box there’s an exhaust fan to cool things off when they get too hot, as well as some power resistors which provide a heat source on the coldest nights. The low-cost build certainly fits the bill, and it’s not too hard on the eyes either.

Cellphone Battery Booster Built At The Checkout Counter

October 29, 2011 by Mike Szczys 40 Comments

When you’re away from home and your cellphone runs out of juice it can be a real downer. Sure, you could find a store and buy a wall charger, but wouldn’t it be more fun to build your own battery booster without using tools? [Spiritplumber] did just that, popping into a Radio Shack for the parts, then making his how-to video (embedded after the break) while standing at the checkout counter. You can see he hust set his camera on top of the battery display case and got to work.

He’s using four D cell batteries to provide 6 volts of power. Assuming your phone charges at 5 volts this is going to be just a bit too high, even though there’s some tolerance with most phones. To overcome that obstacle he added a diode to the circuit, taking advantage of the 0.7 volt drop that it brings to the mix. Grab a plug adapter for your model and then just hand twist the connections. [Spiritplumber] admits it would be better to solder these, but in a bind you can get away with it. We looked up some prices for this method and we figure this would cost around $18 (batteries included) depending on the price of the plug adapter for your phone.

Of course if you’re just looking for a way to charge your phone without paying consumer prices there are ways of accomplishing that as well.

Continue reading “Cellphone Battery Booster Built At The Checkout Counter” →

A Smartphone Dock For Your Arm? Why Not?

October 27, 2011 by Jeremy Cook 20 Comments

Why not that is, if you have a prosthetic arm. Although it’s hard to believe we haven’t seen this before, [Trevor Prideaux], according to [The Telegraph’s] article, “has become the world’s first ever patient to have a smartphone docking system built into his prosthetic arm.”

[Trevor] was born without a forearm, and, as he puts it, he’s used to adapting to things. However, he thought others might be struggling with the same problem, especially those that become disabled later in life. Once their help was secured, Nokia and the Exeter Mobility Centre got to work on his new limb and produced a prototype in five weeks!

[Trevor] is quite pleased with his new phone docking system. Texting especially is much easier and safer, and the phone can be removed when needed for making calls. We love to see hacks like this where people enhance their abilities using technology! For another hack helping those with disabilities, check out this wheelchair elevator/winch made for a non-accessible apartment.

via [reghardware.com]

How To Record 3D Video In 3D

October 23, 2011 by Jeremy Cook 17 Comments

Legalities of doing something like this aside, this concept by [MadSci labs] gives some insight into how one would go about recording a 3D movie in 3D. Probably many of you have wondered if this could be done, but they took it one step further and actually made a device capable of doing just that.

[MadSci labs] solution involved taking some 3D glasses home from a theater, cutting them to size, and taping them to a HTC EVO 3D phone. Each lens piece was taped over a different camera lens to separate out the two 3D elements needed to produce a stereoscopic image. Their experiment was successful, however some loss of quality was experienced. Because of this, we’re not expecting to see a lot of in-theater movies pirated this way, but given a more professional-quality build, you never know what will happen.

You can see the “results” of their experiment after the break. As it’s not in 3D, it should give you an idea of what is going on. Continue reading “How To Record 3D Video In 3D” →

Cellphone Microscope For About $20

October 19, 2011 by Mike Szczys 30 Comments

Medical-grade microscope photography for $20 might be a game changer in areas where medical services are unavailable. This particular hack uses an iPhone’s 2 megapixel camera, as well as a tiny glass marble, to magnify a sample to about 350 times its actual size. The two images seen on the left are red blood cells photographed with the improvised microscope. The main issue with this magnification method is a very thin plane of focus that is overcome with processing in software.

This makes us think of the microscope hack that shined a laser through a droplet of water, to project the image on a wall. The concept was later refined to work with samples on glass slides. There are a couple of distinct advantages to using this cellphone-based method. First, the sample can be seen with its true colors. Second, you not only magnify the sample, but you have a digitized image already on a device that connects to the Internet. If you’re trying to make a medical diagnosis this can easily be sent to a qualified professional for analysis.

The team that came up with this technique also figured out how to build a cellphone-based spectrometer for just a few bucks. The image in the upper right is the result of that hack. Both have a step-by-step build guide on the page linked at the top. The microscope is just a glass bead in a piece of rubber, as seen here. The spectrometer is a bit more involved.

[Thanks Fabien]

Easy To Use Automatic QR Code Generator

October 16, 2011 by Mike Nathan 20 Comments

custom_qr_code_generator

Love them or hate them, plenty of people around the world use QR codes on a daily basis. Since he thinks they’re pretty great, Hackaday reader [falldeaf] thought it would be cool to put together an automatic QR code generator to be used on web sites.

Inspired by the custom QR logo embedding work done by our own [Brian Benchoff], his dynamic QR code generator allows you to do the same thing, but with far less work. The code requires that you have PHP and the GD library installed on your server, but other than that his code does the rest.

All you need to do is call up the page and pass along a URL, optional caption text, optional image overlay (to add your logo to the center of the code), as well as an optional hash code for tracking traffic sources. The page spits out a png image that can be used on its own, or embedded in a blog, which is what [falldeaf] plans on using it for.

If QR codes are your thing, be sure to grab a copy of his code, it will certainly be a handy tool to have around.

ATtiny Hacks: An Audio Alert For Cell Phones Accidentally Left On Vibrate

September 15, 2011 by Mike Nathan 31 Comments

ATtiny Hacks Theme Banner
vibe2tone_cell_phone_vibration_alert

[John Thomson] usually keeps his phone on vibrate when it’s in his pocket, and he often forgets to turn the ringer back on when setting it down to charge. This typically results in a bunch of missed calls in the meantime, so he had to devise a way to counteract his forgetfulness.

You might remember [John] from the Santa-pede contest we held last December. He wanted to try his hand at yet another competition, the Avnet Dog Days of Summer contest, so he scrambled to come up with a quick fix for his situation. He concocted a simple circuit based on [ChaN’s] design for a “Simple SD Audio Player with an 8-pin IC” that would alert him to incoming calls, even when his phone was on vibrate.

[John] used an ATtiny85, just as [ChaN] did, adding a speaker for sound output and a piezo sensor to detect his phone’s vibrations. When the piezo senses a bit of motion, the audio player kicks in, blaring a series of sounds that are sure to get [John’s] attention.