Arduino Nixie Shield

June 22, 2009 by Zach Banks 8 Comments

AN_Board_FirstBuild2

Reader [Bradley] sent in his ArduiNIX project, an Arduino shield designed for driving nixie tubes. The shield allows the Arduino to drive and multiplex nixie tubes without any additional hardware. These antique-looking displays are commonly hacked into clocks. It takes 9 volts from a wall wart and steps it up to over 200V in order to drive the displays. The shield is capable of multiplexing up to 80 individual elements. He has example code for driving a 6-digit display and a clock on his site. He is selling kits and completed shields too.

Related: Victorian nixie tube clock

[thanks Bradley!]

WTPA Bendable Sampler

May 3, 2009 by Eliot 23 Comments

wtpa

Where’s the Party At is an open source bendable 8-bit sampler kit created by [Todd Bailey]. The initial design started about a year ago when he was instructing circuit benders how to transition to circuit design. He designed the kit to show how simply you could build a sampler. It demonstrates both clear analog and digital design. It’s meant to be a unique instrument though and features a lot of glitchy/quirky characteristics while being fairly reliable. You can read more about the device on his site. It has comprehensive parts and assembly manuals available and the kit is $75.

[via Create Digital Music]

Through-hole Bus Pirate Kit From Fundamental Logic

March 31, 2009 by Ian 24 Comments

bpv1ath

Fundamental Logic is selling a Bus Pirate kit and bare PCB based on our universal serial interface tool. They started with our serial port-based v1a hardware, and modified it to use all through-hole parts. 8pin DIP LP2951ACN/-3.3 switchable voltage regulators replace the surface mount TPS79650/33 that we used. The PIC is pre-programmed with our latest firmware, version 0f, which includes a bootloader for easy firmware updates through the serial port. Documentation includes illustrated assembly instructions.

Speaking of Bus Pirate goodness, we’re busy working on hardware V2. As astute readers may have already noticed, the final version of the Bus Pirate incorporates an FTDI USB->serial chip, and draws its power from the USB port. We also tackled the software-controlled pull-up resistor feature, and reduced the overall part count and cost. Best of all, we’re working to make assembled PCBs available with world-wide shipping. The how-to should be ready in a few weeks.

Paintball Gun Turret

February 26, 2009 by Eliot 39 Comments

[Jared Bouck] has been sending in his projects for a couple years now. We’ve enjoyed his heavy-duty DDR pads, LCD backlight repair, and ion cooling projects. His latest, an RC paintball gun turret, is our favorite though. He actually rates this as one of the easier projects he’s published; it just took a while to assemble. Several design decisions were made to keep the project simple. Two 32 Degrees Icon-E paintball guns were used. The guns already have electric solenoids for firing, so a special trigger mechanism didn’t have to be fashioned. Q-loaders were used to prevent any ball feed problems. The motors, driver boards, and RC components are all borrowed from combat robots for reliability. He’s hoping to produce a small number of kits based on this design.

Related: We’ve got quite a few sentry gun projects in the archive.

Automated Wire Cutter And Stripper

January 3, 2009 by Eliot 13 Comments

witecutter

Kit builder oomlout—we’ve featured their servo bot—needed to produce a lot of precut wires. After cutting and stripping more than their fair share, they decided to apply some heavy engineering to make things easier. They constructed a machine to do the job for them. It has three main components: a servo driven wire feeder to measure the length, a two servo wire stripper that uses an exacto blade, and finally a wire cutter made from snips and a drill motor. The machine is controlled using an Arduino. They’ve published all the plans and code to Thingiverse incase anyone else wants to build a similar machine for their own kit shop. A video of the machine is embedded below.

Continue reading “Automated Wire Cutter And Stripper” →

Arduino Switch Box

December 4, 2008 by Eliot 12 Comments

arduino_switch

When you’re prototyping a new project, sometimes all you need is a switch. The folks at oomlout were tired of constantly having to rewire things, so they built a universal switch box for the Arduino. It has five potentiometers plus three switches. They’ve put together a software package that monitors the switches and can show you a live view of the knob positions. Have a look at the video below for a demo.

The writeup actually hints at what we can only assume is the next kit they’re releasing: a robot arm. Continue reading “Arduino Switch Box” →

Touchkit – IR Multitouch Screen

July 8, 2008 by Will O'Brien 11 Comments

If you’ve got an extra grand laying around, you can pre-order one of [nortd]’s touchkits. It features a unique custom made acrylic screen with a crap ton of IR LEDs embedded in it. An included IR camera provides the input and a projector (you get to supply your own) is used to light the surface. We mentioned this in our multitouch roundup and you can find a video of it embedded after the break.