Dead Motor? Think Again

September 16, 2010 by Jakob Griffith 28 Comments

While hobby brush motors are pretty cheap now adays, there’s always that feeling of why replace when you can rebuild and reuse. As such [John Carr] presents how to change the brush position in motors to revive a dead motor. So long as the motor dies from natural causes commutator wear, the idea is the brushes can be moved along the axes and fixed to a new portion of commutator that’s not worn at all. [John] also goes through the details of some tricky reassembly, but we think to make this complete a guide on brush replacement and commutator replacement might be in order hint hint.

Electric Scooter Sings As It Travels

August 25, 2010 by Mike Szczys 34 Comments

[youtube=http://www.youtube.com/watch?v=MaQuRnZYKPc]

This scooter has been fitted with a three-phase induction motor. It reminds us of the sound effects from vehicles in the Jetsons. Right now they’re using lead-acid batteries and get about 15 miles of range from one charge. Once they switch over to lithium polymer they calculate the range will be closer to 45 miles due to the reduced weight and increased capacity. Not bad for $600 in parts, and we’d bet it’s both faster and more stable than the one-wheeled-wonder we saw last week.

A Different Take On Electric Motor Cars

August 23, 2010 by Jakob Griffith 43 Comments

[Craig Carmichael] has been hard at work on his electric hub motor for cars. Unlike typical electrical vehicles the plan is to bypass the transmission, differential, and everything else all together by connecting directly to the hub of the wheel. The goal of giving greater thrust and still allowing the use of a gas engine if need be.

There’s really too much detail for us to even begin to try to explain the entire project in a short recap, but [Craig] builds the entire motor (from magnets to coil windings) and wires his own controller (from schematic to finished PCB), all while documenting the process thoroughly for those wishing to make their own.

Heel Treads Make Shoes Go

July 7, 2010 by Mike Szczys 50 Comments

Motorized treads as a replacement for the heel of your shoe? Okay, remember how The Jetsons had moving sidewalks everywhere so you wouldn’t have to walk at all? Well, there’s a much more efficient way to do it and Treadway Mobility seems to have figured it out. In the video after the break you can see several of their prototype units zipping the wearer around quite happily. We think the best part is that with the tread locked in place you can stand and walk like normal, assuming you don’t feel like you have a block of concrete attached to each foot. Maybe the real question is which is more geeky, this or the power lace shoes?

Continue reading “Heel Treads Make Shoes Go” →

Did That Table Just Move?

June 7, 2010 by Mike Szczys 20 Comments

[vimeo=http://vimeo.com/11674851]

A table and chair that can move around by themselves? What’s next, suicide booths, self-replicating robots, and Star Trek styled tablet computers? It seems that [Adam Lassy] is moving in that direction. He took this furniture from Ikea and made some neat modifications to give it mobility. Each of the four legs has wheels on them and the legs themselves rotate in unison to change the direction of travel. We could see the table as a more practical drink delivery system than the Bar2d2. It certainly would make for some great late-night pranks but the chair motors need to be silenced before that can happen.

[Thanks Balbor via Ikea Hacker]

How-to: DIYDTG

June 6, 2010 by Jakob Griffith 130 Comments

For those unaware, the little acronym above stands for Do-It-Yourself-Direct-To-Garment printing. In layman’s terms, printing your own shirts and designs. Commercial DTGs can cost anywhere from $5,000 to $10,000 which for the hobbyist who only wants a few shirts is ridiculous. So you would think this field of technology would be hacked to no end, but we’ve actually only seen one other fully finished and working DIYDTG. So we took it upon ourselves to build a DIYDTG as cheaply and as successfully as possible. Continue reading “How-to: DIYDTG” →

TOBY: Reel Mower Bot evolved

May 10, 2010 by Mike Szczys 13 Comments

[Grayson Sigler] rolled out a new version of his robotic mower which he calls TOBY. The previous design added motors to a reel mower but he had trouble with traction. The new design is more of a utility robot platform that is used to tow the reel motor behind it. With better wheels, a much more stable base, and plenty of power this is a significant improvement.

His parts order came since we last checked in and he now has RC fully implemented. Check out the video after the break.

Continue reading “TOBY: Reel Mower Bot evolved” →