Add Some Blinkenlights To Your Supercon Badge

December 1, 2023 by Kristina Panos 14 Comments

We’re not sure what is more amazing here: the glow of the blinkenlights themselves, the tedium involved in creating it, or the fact that [makeTVee] soldered 280 microscopic WS2812 LEDs while at Supercon.

This hack began before the con when [makeTVee] designed the LED-diffusing frame in Fusion 360 and printed it in clear resin. Rather than solder the LEDs straight, the frame has 280 teeth that support each one at a 55° angle.

Not only does this look cool, it makes the bridging of DOUT to DIN much easier. That leaves GND and VCC to be painstakingly connected with 30 AWG wire. How, you might ask? With a little help from 3.5x magnifying glasses and the smallest soldering iron tip available, of course.

But that’s not all. Since 280 addressable LEDs need a lot of power, [makeTVee] also designed a holder for the LiPo battery pack that fits into the existing AA holders.

Want to see more awesome badge hacks? Check out the compendium.

Hacked Tea Lights Flicker Just Right

November 30, 2023 by Kristina Panos 17 Comments

Flickering LED tea lights are a friendly and safe alternative to having flaming little pots of wax situated around your home, but sometimes the flicker scheme leaves something to be desired.

[Roger Rabbit] found a set of six such rechargeable tea lights with a base and a remote, and replaced the controller with an ATtiny85 for a more realistic flicker. When [Roger] opened up one of the candles, they found an IR sensor for the remote, a driver chip, and of course, an LED. No surprises there.

After desoldering the original controller, [Roger] wired in a socketed ATtiny85 on a piece of perfboard and hooked everything back up.The coolest part of this hack might just be the fact that there’s a perfect little compartment for the new microcontroller. How about that?

The Arduino code for this project is available in the Git repository, and the wonderful instruction manual is available in PDF form. Be sure to check out the brief video after the break.

You like these flickering LED candles? Here’s one you can blow out.

Continue reading “Hacked Tea Lights Flicker Just Right” →

Autonomous Excavator Builds Stone Wall Algorithmically

November 30, 2023 by Kristina Panos 21 Comments

In a move that aims to further the circular economy of the construction industry, researchers at ETH Zurich have let an autonomous excavator loose on a big pile of boulders and reclaimed concrete. The goal? To build a 20 foot (6 meter) and 213 ft (65 m) long dry-stone wall as part of a park where the landscape was digitally planned, and the earth autonomously excavated.

The coolest thing about the Menzi Muck excavator is the software, which is explored in the video after the break. Thanks to a bunch of sensors, the excavator can not only draw a 3D map of the site, it can find in situ boulders dotting the landscape and incorporate them into the wall.

Machine vision allows the excavator to grab the stones and assess their size and shape, as well as approximate their weight and center of gravity.

Then, an algorithm determines the best place for each stone and places them there without using mortar or cement. Menzi Muck is capable of number-crunching 20 to 30 stones at a time, which coincidentally is about the number in one delivery.

Want to build your own excavator? Check out this finely-detailed R/C excavator for top-notch inspiration.

Continue reading “Autonomous Excavator Builds Stone Wall Algorithmically” →

Iowa Demolishes Its First 3D Printed House

November 29, 2023 by Kristina Panos 130 Comments

It sounds like a headline from the future: the weekend before Thanksgiving, a bulldozer came for the first example of a printed home that was supposed to help the housing crisis in the city of Muscatine. Fortunately, it hadn’t been completed and sold yet.

Printing of this first house began in May 2023, and nine more were to be completed by the end of the year. Unfortunately, when tested for compressive strength, the cement mixture this first home was printed out of failed to meet the 5,000 PSI minimum required for the project. Rather than compromise on safety, the parties involved decided to knock it down and start over.

The goal now is to find out why the mixture, which met the strength requirements in laboratory testing, didn’t behave the same on-site. Currently, the plan is to start building the originally-planned second house in the spring, and begin construction on this first site after that.

The project is a collaborative effort between the Community Federation of Greater Muscatine (CFGM), Muscatine Community College, and Alquist 3D. Want to know more about the state of 3D printing when it comes to housing? Check out our handy guide.

Editors Note: The initial post initially indicated that the failed cement mixture contained hemp, but that has since found to be incorrect and the post has been edited accordingly.

Continue reading “Iowa Demolishes Its First 3D Printed House” →

LED Ring Brings The Bling

November 28, 2023 by Kristina Panos 10 Comments

We’ve seen our share of light-up jewelry over the years, but for some reason — probably power — it’s almost always earrings or necklaces. So when we saw [ROBO HUB]’s LED ring, we had to check it out. It involves a bit of behind-the-scenes action in the form of a battery holder that you palm, but the end effect is quite cool.

Essentially, this is a 3D printed ring with SMD LEDs painstakingly soldered together in parallel along a pair of thin copper wires. The ring itself is in two parts: a base, and a cover to diffuse and protect the LEDs. A pair of wires run out from the ring and connect to a printed coin cell holder.

Continue reading “LED Ring Brings The Bling” →

Bowling With Strings Attached: The People Are Split

November 28, 2023 by Kristina Panos 52 Comments

There’s a bowling revolution in play, and not all bowlers are willing participants. In fact, a few are on strike, and it’s all because bowling alleys across America are getting rid of traditional pinsetting machines in favor of a string-based system.

In hindsight, it seems obvious to this American: attach strings to the tops of bowling pins so they can be yanked upward into holes that settle down the action so that the pins can be reset. In fact, European bowling “houses” have used string pinsetters for decades, instead of lumbering machinery that needs regular maintenance and costs several thousand dollars a month to maintain.

Continue reading “Bowling With Strings Attached: The People Are Split” →

Swatch Internet-Time Clock Doesn’t Miss A Beat

November 27, 2023 by Kristina Panos 21 Comments

The thing about human invention is that occasionally, two or more people think of an idea around the same time, and it’s difficult to determine who was first. Such is the case with Swatch’s Internet time, which is told in something called “.beats”. Rather than using hours and minutes, the solar day in the .beat system is divided into 1,000 parts equal to one minute in the French Revolutionary decimal time system, or 1 minute and 26.4 seconds of standard time.

Swatch came up with .beats to sell their special line of .beats watches. But they weren’t the only ones to divide the solar day this way. A few months before Swatch’s announcement of .beats time, a Argentinian drummer named [Charly Alberti] came up with the same idea and created a website for it to display the current Internet time of day.

The point of all this is that [Roni Bandini] has created an homage to both .beats and [Charly] in the form of a small clock. The main brain is a Seeed Studio Xiao nRF52840, with a Xiao TFT round display to show the time as well as a tribute to [Charly]. The 3D-printed stand incorporates a cylindrical power source. We think the black and white images, which [Roni] created with Dall-e, look fantastic.

Interestingly enough, the Xiao has no Internet connectivity; the time is set manually via hard-coded variable, and then the display’s RTC keeps track of the seconds and convert them to Internet time. Check out the brief build video after the break.

Interested in regular old metric time? Here’s a modern metric clock.

Continue reading “Swatch Internet-Time Clock Doesn’t Miss A Beat” →