Introducing The Raspberry Pi 3

February 28, 2016 by Brian Benchoff 250 Comments

TL;DR: The Raspberry Pi 3 Model B is out now. This latest model includes 802.11n WiFi, Bluetooth 4.0, and a quad-core 64-bit ARM Cortex A53 running at 1.2 GHz. It’s a usable desktop computer. Available now at the usual Pi retailers for $35.

News of the latest Raspberry Pi swept around the Internet like wildfire this last weekend, thanks to a published FCC docs showing a Pi with on-board WiFi and Bluetooth. While we thank the dozens of Hackaday readers that wrote in to tell us about the leaked FCC documents, our lips have been sealed until now. We’ve been doing a few hands-on tests with the Pi 3 for about two weeks now, and the reality of the Pi 3 is much cooler than a few leaked FCC docs will tell you.

The Raspberry Pi 3 Model B features a quad-core 64-bit ARM Cortex A53 clocked at 1.2 GHz. This puts the Pi 3 roughly 50% faster than the Pi 2. Compared to the Pi 2, the RAM remains the same – 1GB of LPDDR2-900 SDRAM, and the graphics capabilities, provided by the VideoCore IV GPU, are the same as they ever were. As the leaked FCC docs will tell you, the Pi 3 now includes on-board 802.11n WiFi and Bluetooth 4.0. WiFi, wireless keyboards, and wireless mice now work out of the box.

Continue reading “Introducing The Raspberry Pi 3” →

FCC Locks Down Router Firmware

February 26, 2016 by Brian Benchoff 112 Comments

For years, we have been graced with consumer electronics that run some form of Linux, have a serial port on the circuit board somewhere, and are able to be upgraded through official and unofficial means. That digital picture frame you got for Christmas in 2007 and forgot to regift in 2008? That’s a computer, and it would make a wonderful Twitter feed display. Your old Linksys WRT54G router? You can make a robotic lawnmower out of that thing. The ability to modify the firmware of consumer electronics is the cornerstone of Hackaday’s editorial prerogative. Now that right we have all enjoyed is in jeopardy, thanks to regulations from the FCC and laziness from router manufacturers.
Continue reading “FCC Locks Down Router Firmware” →

Dr Noirimetla, Private Failure Investigator And The Mystery Of Galileo’s Pillars

February 25, 2016 by Gerrit Coetzee 115 Comments

One dark and stormy morning, Dr. Richard Noirimetla, private failure investigator, was sitting at his desk nursing his morning cup of joe. It was an addiction, but life, and engineering was hard. Intense eyes sat in a round dark-skinned face. An engineering degree from the prestigious Indian Institute of Technology hung from the wall in his sparse office. Lightning flashed outside of his window, as the rain began to beat even harder against his corner office windows.

His phone rang.

“Hello, Dr. Noirimetla, Private Failure Investigator here.” He said in deep, polite voice. “How may I help you?”

“Ah, I’m Chief of Manufacturing for Galileo Concrete Pillars Inc. We have a bit of a problem here. We used to see a failure rate above 33% for our concrete pillar operation. As part of our lean manufacturing efforts we tried to reduce that number through various improvements. However, we see a failure rate of almost 50% now. We expect foul play… from one of our suppliers. Can you come right away?” a worried man’s voice sounded over the phone.

“I see, that’s very troubling,” Noirimetla rumbled. “I’ll send over the contract detail. There will be an increased fee, but I’m on my way.”

“Sounds good, we’ll pay anything! Just get our operation up to standards!” The man bid a polite goodbye and hung up.
Continue reading “Dr Noirimetla, Private Failure Investigator And The Mystery Of Galileo’s Pillars” →

Frackers: Inside The Mind Of The Junk Hacker

February 25, 2016 by Elliot Williams 116 Comments

Hackers can be a diverse bunch. My old hackerspace had folks ranging from NSA employees (ahem, independent security contractors) to space-probe pilots to anarchist vegan punks. And we all got along because we shared a common love for what we’re doing. One summer night we were out late in Adams Morgan and my vegan-punk friend reaches into the trash can and pulls out a discarded pepperoni Jumbo Slice.

“Wait a minute! Vegans don’t eat pepperoni pizza with cheese.” But my friend was a “freegan” — a vegan who, for ethical reasons, won’t buy meat or milk but who also won’t turn it down if it’s visibly going to waste. It’s actually quite a practical and principled moral proposal if you think about it: he’s not contributing to the use of animals that he opposes, but he gets to have a slice of pizza just the same. And fishing a slice of pizza, in a cardboard container, off the top of the trashcan isn’t as gross as you’d imagine, although it pays to be picky.

A Fracker is Born

That was the night that we realized we all had something deeper in common: we were all “frackers”. If you’ve been around hackers long enough, you’ll have noticed this tendency, but maybe you’ve never put a name to it. Tearing something apart, even if you might break it in the process, isn’t a problem if you fished it out of the e-waste stream to begin with. If you’re able to turn it into something, so much the better. It’s all upside. Need practice de-soldering tricky ICs? Looking for a cheap target to learn reverse engineering on? Off to the trashcan! No hack is too dirty, no method too barbaric. It’s already junk, and you’re a fracker.

Do you have a junk shelf where you keep old heatsinks in case you need to cut some up and use it? Have you used a heat gun more frequently for harvesting parts than for stripping paint? Do you know that certain satisfaction that you get from pulling some old tech out of the junk pile and either fixing it up again or, better yet, making it do something else? You might just be a fracker too.

Continue reading “Frackers: Inside The Mind Of The Junk Hacker” →

Hackaday Prize Worldwide: Dallas

February 24, 2016 by Brandon Dunson 11 Comments

Join us for a Meetup on Saturday, March 19th in the Lone Star State. Team Hackaday will be at the Dallas Makerspace and we want to hang out with you. Bring a hack to show off and come see what everyone else in the area has been up to.

Come join us for food, drinks and lightning talks. If you aren’t familiar with lightning talks it’s pretty simple, they’re designed to be short and to the point talks no longer than 7 minutes. Bring one of your hacks and 5 to 7 minutes of bragging rights to show off. Or perhaps you are working on a new project and need some help, what better audience to bounce ideas off of? Come on out and show us what you got no matter what stage of the project you’re in, we want to see it and hear all about it.

This is a free event and you are not required to be a member of the Dallas Makerspace to attend, however we do want you to RSVP if you plan to come.

We can’t wait to see what you’ve been working on and we want to hear all about it. We will also have a few Hackaday related talks: [Mike Szczys] is giving a talk on Hackaday Belgrade and [Brandon Dunson] is giving a talk on the 2016 Hackaday Prize. The monthly hardware design workshop I will be teaching at the Dallas Makerspace starting in April: Mrs Penny’s Driving School will also be the topic of a lightning talk. Full disclosure: [Mike Szczys] also hinted at giving another talk but we’ll have to wait and see what he chooses to talk about.

A Field Guide To The North American Utility Pole

February 22, 2016 by Dan Maloney 149 Comments

We live under the umbrella of an intricate and fascinating web of infrastructure that enables every aspect of modern technology. But how often do we really look at it? I’ve been intrigued by utility poles for years, and I’ve picked up a thing or two that I’d like to share. Bear in mind these are just my observations from the ground in my area; I’m sure utility professionals will have better information, and regional practices will no doubt lead to very different equipment arrangements. But here’s a little of what I’ve picked up over my years as a pole geek.

Continue reading “A Field Guide To The North American Utility Pole” →

Kicking The Tires Before You Buy: 3d Printers

February 22, 2016 by Gerrit Coetzee 103 Comments

So you’re looking to buy your first 3D printer, and your index finger is quivering over that 300 US Dollar printer on Amazon.com. Stop! You’re about to have a bad time. 3D printing has come a long way, but most 3D printers are designed through witchcraft, legends, and tall tales rather than any rigorous engineering process. I would say most 3D printer designs are either just plain bad, or designed by a team of Chinese engineers applying all their ingenuity to cost cutting. There are a few that are well designed, and there is a comparatively higher price tag attached.

I’ll start by going through some of the myths and legends that show up in 3D printers. After that I’ll go through some of the common, mostly gimmick, features that typically hinder your printer’s ability, rather than adding any useful function. Next I’ll go onto the things that will actually make your printer better. Finally, I’ll add some special consideration if you’re a beginner buying your first printer.

Continue reading “Kicking The Tires Before You Buy: 3d Printers” →