Build Your Own Steel Reinforced Storm Shelter

July 1, 2013 by Mike Szczys 58 Comments

build-a-steel-reinforced-storm-shelter

The last few years have seen a lot of dangerous storms rip through middle section of the United States. We’re surprised to hear that many residents in that part of the country don’t have basements to take refuge in when in imminent danger. But a resourceful hacker will always be able to find a way to improve their own situation. This example is particularly useful. It’s a steel storm shelter which opens into the garage.

It all starts with a cage made of square tube. With the skeleton fully assembled it is wrapped in steel plate, adding weld joints running nearly the entire length of each of the cage’s ribs. The image at the left shows the steel door frame clamped in position. Check out the finished version on the right after the shelter has been slid into place and bolted to the concrete slab.

The Reddit discussion includes a debate on whether the door should swing in or out. Swinging out means you could be trapped if the opening is blocked by debris. But there may be scientific research that proves this is a better orientation. Either way, we hope the three dead bolts, door latch, and heavy-duty hinges will stand up to the pressure if this is ever used.

How To Build A Tron Bar That Daft Punk Would Hang Out At

June 24, 2013 by Mike Szczys 24 Comments

tron-bar-daft-punk

Sure, the bar in this image looks pretty neat. But the video showing off its synchronization with the music brings it to the next level. The flashing lights and EL wire put on a quite a show that may make the bartenders feel like they’ve already had a few too many.

The most amusing part of the project is that it all started from that half bookcase mounted on the wall. [Alexander Givens] and his roommate decided to augment its usefulness as a liquor cabinet by building a bar around it. But why stop there? LED Strips and 120 feet of elecroluminescent wire give the bar its inner glow. The illuminated lines are obvious, but the LED strip locations may not be. Several of them light the shelves hosting liquor and glass wear. The bartop itself is made of glass, filled with 75 pounds of marbles, and lit from underneath by the rest of the strips.

An Arduino Mega with an EL shield drives the system. The guys built a rudimentary control interface that looks partially spill tolerant. It’s located just under the inside lip of the bar.

Their costumes came out pretty well too. But with a built-in centerpiece like this they may want to upgrade to a more accurate replica.

Continue reading “How To Build A Tron Bar That Daft Punk Would Hang Out At” →

PBX Blade For Multiple Extension Home Telephony

June 19, 2013 by Mike Szczys 18 Comments

home-pbx-blade

It looks like a consumer good, but this PBX server blade was built by [Benoit Frigon] over the last couple of years. It brings multiple telephone extensions to his home service.

The device runs Asterisk open source PBX software. Because it will be on all the time he wanted something that doesn’t draw a lot of power. The 500 Mhz system seen on the left has just a half a gig of ram. It’s enough to do the job and at 10 Watts it’s not going to break the bank when it comes to paying the electric bills. The board in the middle is used to interface the analog handsets with the land line. From the look of it he’s got it rigged for two extensions.

That’s all somewhat par for the course with PBX rigs, but the enclosure is where he really shines. [Benoit] used 22 gauge aluminum sheet to fabricate the enclosure which is designed to blend in with the rest of his home’s rack mount hardware. To provide control at the rack he added his own LCD and touch-sensitive button interface to the front of the case based on a PIC 18F2520. The system can also be accessed via the web thanks to a custom interface he coded.

[Frank] Builds A Chair From A Sequoia

June 18, 2013 by Brian Benchoff 1 Comment

[Frank Howarth] is a very competent woodworker known on the YouTubes for his wonderful stop-motion videos of turned wood bowls. Lately, though, he’s put some effort into building furniture, this time a beautiful lawn chair made from a gigantic sequoia log.

A few years ago, [Frank] and a friend acquired a gigantic sequoia log and milled it themselves with a chainsaw. After two summers, the huge boards were finally dry enough to be used and [Frank] decided a lawn chair would be a fine project.

The sides of the chair are a single monolithic piece of wood. Of course [Frank] needed to cut the sides in half and join them together again for the decorative holes, but it’s still an impressively solid piece of woodworking. The back and seat of the chair are also made out of the same sequoia board, cut into slats held together with three very large dowel rods.

This project probably wouldn’t be possible if it weren’t for the awesome equipment and tools [Frank] has in his shop. He has a great tour of his shop available for your viewing. We should all be so lucky.

Wet Spill Vacuum Cleaner Attachment

June 13, 2013 by Mike Szczys 45 Comments

wet-spill-vacuum-attachment

You’ve got to hand it to [Lou], not only does he know how to build simple items, he also knows how to sell their worth. Here’s a wet spill vacuum cleaner attachment which you can build on the cheap. A picture of the final product fails to have the same impact as his video showing its use in cleaning up a simulated cat disgorging from the carpet.

From the picture we’re sure you’ve already figured out how it work. The air and damp matter come in one side and are dropped into the jar as the air is sucked out the other. [Lou] suggests raiding your recycling bin for the jar. The intake and outflow are both pieces from a PVC P-trap intended for a sink drain. They have a threaded flange which keeps the part from pulling all the way through the 1.5″ holes drilled in the lid.

This is going to work best with a high-flow shop vacuum. So while you’ve got the tools out, why not build a dust separator as well?

Continue reading “Wet Spill Vacuum Cleaner Attachment” →

Complicated IPhone Garage Door Opener

June 1, 2013 by Mike Szczys 28 Comments

iphone-garage-door-opener

The round-about way this iPhone garage door opener was put together borders on Rube Goldberg. But it does indeed get the job done so who are we to judge? Plus you have to consider that the Apple products aren’t quite as hacker friendly as, say, Android phones — so this may have been the easiest non-Jailbreak way.

The main components that went into it are the iPhone, a Wemo WiFi outlet, and a 110V rated mechanical relay. But wait, surely it can’t be that simple? You’re correct, just for added subterfuge [Tall-drinks] rolled IFTTT into the mix.

You may remember hearing about If This Then That from the Alert Tube project. It’s a web-based natural language scripting service. Throw everything together and it works like this: The iPhone sends a text message which IFTTT converts to a Wemo command. A power cord connects the Wemo outlet to the 110V electrodes on the relay. The normally open connection of the relay is attached to the same screw terminals of the garage door opener as the push button that operates it. When the relay closes, the garage door goes up or down.

The biggest problem we have with this is the inability to know if your garage door is open or closed.

Scratch-built Desk Adjusts So You May Sit Or Stand

May 21, 2013 by Mike Szczys 52 Comments

custom-height-adjustable-battlestation

Knowing that this desk was built from scratch is pretty impressive. But the motorized legs that raise and lower the desk to any height really puts the project over the top.

Surprisingly this started off as a computer case project. [Loren] upgraded his hardware and couldn’t find a case that would organize it the way he liked. His desk at the time had a glass top and he figured, why not build a new base for the glass which would double as a computer case? From there the project took off as his notebook sketches blossomed into computer renderings which matured into the wooden frame seen above.

Much like the machined computer desk from last December this uses motorized legs to adjust the height of the desk. These cost about $50 each, and he used four of them. If you consider the cost of purchasing a desk this size (which would not have been motorized) he’s still not breaking the bank. This battlestation is now fully functional, but he does plan to add automated control of the legs at some point. We think that means that each has an individual adjustment control which he wants to tie into one controller to rule them all.