What Game Should Replace Doom As The Meme Port Of Choice?

February 27, 2025 by 113 Comments

DOOM. The first-person shooter was an instant hit upon its mrelease at the end of 1993. It was soon ported off the PC platform to a number of consoles with varying success. Fast forward a few years, and it became a meme. People were porting Doom to everything from thermostats to car stereos and even inside Microsoft Word itself.

The problem is that porting Doom has kind of jumped the shark at this point. Just about every modern microcontroller or piece of consumer electronics these days has enough grunt to run a simple faux-3D game engine from 1993. It’s been done very much to death at this point. The time has come for a new meme port!

Good Game

Doom became a popular meme port for multiple reasons. For one, it’s just complex and resource-intensive enough to present a challenge, without being so demanding as to make ports impractical or impossible. It’s also been open-source for decades, and the engine has been hacked to death. It’s probably one of the best understood game engines out there at this point. On top of that, everybody plays Doom at some point, and it was one of the biggest games of the 90s. Put all that together, and you’ve got the perfect meme port.

However, you can always have too much of a good thing. Just as The Simpsons got old after season 10 and Wonderwall is the worst song you could play at a party, Doom ports have been overdone. But what other options are there? Continue reading “What Game Should Replace Doom As The Meme Port Of Choice?” →

A Precisely Elegant Cyberdeck Handheld

February 27, 2025 by 15 Comments

[Nicholas LaBonte] shows off a Cyberdeck Handheld that demonstrates just how good something can look when care and attention goes into the design and fabrication. He wanted to make something that blended cyberpunk and nautical aesthetics with a compact and elegant design, and we think he absolutely succeeded.

On the inside is a Raspberry Pi and an RTL-SDR. The back of the unit is machined from hardwood, and sports a bronze heat sink for the Raspberry Pi. The front has a prominent red PSP joystick for mouse input and a custom keyboard. The keyboard is especially interesting. On the inside it’s a custom PCB with tactile switches and a ATmega32U4 running QMK firmware — a popular choice for DIY keyboards — and presents to the host as a regular USB HID device.

The keys are on a single plate of little tabs, one for each key, that sits between the front panel and press on the tact switches inside.

How did he make those slick-looking keys? It’s actually a single plate that sits between the front panel and the switches themselves. [Nicholas] used a sheet of polymer with a faux-aluminum look to it and machined it down, leaving metal-looking keys with engraved symbols as tabs in a single panel. It looks really good, although [Nicholas] already has some ideas about improving it.

On the right side is the power button and charging port, and astute readers may spot that the power button is where a double-stack of USB ports would normally be on a Raspberry Pi 5. [Nicholas] removed the physical connectors, saving some space and connecting the USB ports internally to the keyboard and SDR.

As mentioned, [Nicholas] is already full of ideas for improvements. The bronze heat sink isn’t as effective as he’d like, the SDR could use some extra shielding, and the sounds the keyboard ends up making could use some work. Believe it or not, there’s still room to spare inside the unit and he’d maybe like to figure out a way to add a camera, GPS receiver, or maybe a 4G modem. We can’t wait! Get a good look for yourself in the video, embedded below.

Continue reading “A Precisely Elegant Cyberdeck Handheld” →

Shelved Kindle Gets New Life As Weather Display

February 27, 2025 by 8 Comments

In the rush to always have the latest and greatest, it’s not uncommon that perfectly serviceable hardware ends up collecting dust in a drawer somewhere. If you’ve got an old Kindle laying around, you may be interested in this write-up from [Hemant] that shows a practical example of how the popular e-reader can be pushed into service as a weather dashboard.

The first step is to jailbreak the Kindle, providing the user with root access to the device. From there the Kindle Unified Application Launcher (KUAL) is installed along with USBNetwork which allows you to connect to the reader over SSH. With root access and a network connection, the real project of converting it to a weather dashboard begins. [Hemant] split the project into two parts here, a Node.js server that scrapes weather data from the internet and converts it into an image, and a client for the Kindle that receives this image for display.

The Kindle has a number of quirks and issues that [Hemant] covers as well, including handling image ghosting on the e-ink display as well as a problem where the device will hang if the Internet connection is lost. For those with jailbroken Kindles that want to put their devices back into useful service, this is an excellent guide for getting started and [Hemant] also provided all of the source code on the project’s GitHub page.

There has been a long tradition of using Kindles for things other than e-readers, and even devices with major hardware problems can still have useful life in them thanks to this project which allows the e-ink display to have a second life on its own.

SHOUT For Smaller QR Codes

February 26, 2025 by 19 Comments

QR codes have been with us for a long time now, and after passing through their Gardenesque hype cycle of inappropriate usage, have now settled down to be an important and ubiquitous part of life. If you have ever made a QR code you’ll know all about trying to generate the most compact and easily-scannable one you can, and for that [Terence Eden] is here with an interesting quirk. Upper-case text produces smaller codes than lower-case.

His post takes us on a journey into the encoding of QR codes, not in terms of their optical pattern generation, but instead the bit stream they contain. There are different modes to denote different types of payload, and in his two examples of the same URL in upper- and lower- cases, the modes are different. Upper-case is encoded as alphanumeric, while lower-case, seemingly though also containing alphanumeric information, is encoded as bytes.

To understand why, it’s necessary to consider the QR codes’ need for efficiency, which led its designers to reduce their character set as far as possible and only define uppercase letters in their alphanumeric set. The upper-case payload is thus encoded using less bits per character than the lower-case one, which is encoded as 8-bit bytes. A satisfying explanation for a puzzle in plain sight.

Hungry for more QR hackery? This one contains more than one payload!

An overhead shot of a parking lot. A road with cars parked along it is on the right hand side of the image. The top center shows a drilling rig on tracks drilling at a slight angle into the ground. Many different semi trailers dot the parking along with several different pallets of construction supplies. An excavator and skylift/forklift are also at work in the lot.

District Heat Pump Systems Save Money And Gas Utilities

February 26, 2025 by 50 Comments

Ground-source heat pump systems are one of the most efficient ways to do climate control, but digging the wells can be prohibitively expensive for the individual citizen. What if you could do it at a larger scale?

Starting with a pilot to serve 37 commercial and residential buildings in Framingham, MA, Eversource is using its experience with natural gas drilling and pipe to serve up a lower carbon way to heat and cool this neighborhood. While district heating via geothermal has precedents elsewhere in the country, Boise is a notable example, it has remained a somewhat niche technology. Once networked, excess heat from one location can be used elsewhere in the system, like data centers or industrial facilities being used to heat homes in the winter.

As gas utilities look to transition away from fossil fuels, their existing knowledge base is a perfect fit for geothermal, but there are some regulatory hurdles. Six states have passed laws allowing natural gas utilities to expand beyond just gas, and bills have been filed in six more. This will likely accelerate with the formation of the Utility Networked Geothermal Collaborative which includes many utilities including giants like Dominion Energy who are looking to expand their energy portfolios.

If you want to dig more into district heating systems or geothermal energy, we’ve covered cogeneration from power plants to serve up the heat instead, doing it with wind, or even using old coal mines for geothermal heat.

Building A DIY Muon Tomography Device For About $100

February 26, 2025 by 24 Comments

Muon tomography, or muography, is the practice of using muons generated by cosmic rays interacting with Earth’s atmosphere to image structures on Earth’s surface, akin to producing an X-ray. In lieu of spending a fair bit of money on dedicated muon detectors, you can also hack such a device together with two Geiger-Müller tubes and related circuitry for about $100 or whatever you can source the components for.

The reason for having two Geiger-Müller tubes is to filter out other much more prevalent sources of ionizing radiation that we’re practically bathed in every second. Helped by a sheet of lead between both tubes, only a signal occurring at the same time from both tubes should be a muon. Specially cosmic ray muons, as these have significantly more kinetic energy that allows them to pass through both tubes. As a simple check it’s helpful to know that most of these muons will come from the direction of the sky.

The author of the article tested this cobbled-together detector in an old gold mine. Once there the presence of more rock, and fewer muons, was easily detected, as well as a surge in muons indicating a nearby void from a mine shaft. While not a fast or super-easy way to image structures, it’s hard to beat for the price and the hours of fun you can have while spelunking.

A bright yellow crew cab pickup is on an unpaved area with snow-capped mountains in the distance. In its bed is a matching camper shell which is somewhat trapezoidal with a smaller semicircular section that can pull out to lengthen the sleeping space of the camper. At the top of the image it says, "Sleeps Two!" with an arrow pointing to the camper shell.

Want A Truck With A Short Bed And A Long Camper Shell?

February 26, 2025 by 37 Comments

Camper shells are a time-honored piece of truck gear, but with modern trucks having increasingly vestigial beds, the length of your overnight abode has increasingly shrunk as well. To combat this problem, [Ed’s Garage] built a camper shell that extends once you’ve arrived at your campsite.

[Ed] wanted to keep things relatively low profile while still tall enough to sit up in for convenience, leading to a small bit of the shell peeking over the truck’s roof. To keep the cold Canadian winter out, attention was paid to proper weather sealing around the sliding portion of the shell so that it stays warm and dry inside.

While this would work on any truck, the mains power plugs in the bed of some modern trucks mean that certain glamping conveniences like a heater and projector can be easily powered while you’re in camp. We get to see the camper shell in action at the end of the video where the pros and cons of having your sleeping space also being your storage while en route become apparent.

If you’re looking for something a little less conventional for your camping experience, how about this solar camper or this retro bike camper?

Continue reading “Want A Truck With A Short Bed And A Long Camper Shell?” →