Warm Up To Cooking With A Recipe-Randomizing Toaster

April 8, 2020 by Kristina Panos 10 Comments

Did you get a thermal printer when they were hot stuff, but then your interest cooled when you couldn’t decide what to do with it? Something similar happened to [Sunyecz22], and the poor printer sat unused until that magical day when the perfect use for it popped up — a random recipe receiver in the form of a toaster.

[Sunyecz22] was tired of searching for recipes every week before going to the grocery store. Between the millions of recipe options on the internet and the 1000-word essays that precede them all, the process was like a part-time job. Now all they have to do is push the little lever down and wait for a recipe to get toasted into some thermal paper. It doesn’t print the full recipe, only the essentials, and we love that. You get the name, the prep time, a rating, and a QR code that links to the recipe page.

This toaster runs on a Raspberry Pi Zero W that fetches recipes using the Spoonacular API and sends the deets to the printer. The lever makes use of some old pen springs to activate a limit switch and start the recipe-getting process. We think it would be extra cool if it stayed down until the recipe popped up. Butter your way past the break to see a short demo video.

We must say, this toaster is way more helpful than the talkie toaster from Red Dwarf.

Continue reading “Warm Up To Cooking With A Recipe-Randomizing Toaster” →

Impressive Lever-Press Espresso Machine Has Finesse

April 8, 2020 by Kristina Panos 8 Comments

Some people will do anything for a good cup of coffee, and we don’t blame them one bit — we’ve been known to pack up all our brewing equipment for road trips to avoid being stuck with whatever is waiting in the hotel room.

While this stylish lever-based industrial coffee machine made by [exthemius] doesn’t exactly make textbook espresso, it’s pretty darn close. Think of it like an Aeropress on steroids, or more appropriately, bulletproof coffee. As you can see in the demo after the break, the resulting coffee-spresso hybrid brew looks quite tasty.

Here’s how it works: finely-ground beans go in a pressurized portafilter basket that was scavenged from an entry-level prosumer espresso machine. Pour boiling water into the top of the cylinder, and pull the giant lever down slowly to force it through the portafilter. Presto, you’re in thin, brown flavor town.

We love the piston-esque plunger that [exthemius] made by layering washers and rubber gaskets up like a tiramisu. Although there are no plans laid out, there’s probably enough info in the reddit thread to recreate it.

If you ever do find yourself stuck with hotel house brand, soak it overnight to make it much more palatable.

Continue reading “Impressive Lever-Press Espresso Machine Has Finesse” →

Simon Says, But With Servos

April 7, 2020 by Kristina Panos 12 Comments

How much easier would life be if you could just grab hold of whatever mechanism you wanted to manipulate, move it like you want, and then have it imitate your movements exactly? What if you could give a servo MIDI-like commands that tell it to move to a certain location for a specific duration? Wonder no more, because [peterbiglab] has big-brained the idea into fruition.

With just one wire, an Arduino, and some really neat code, [peter] can get this servo to do whatever he wants. First he tells the Arduino the desired duration in frames per second. Then he grabs the horn and moves it around however he wants — it can even handle different speeds. The servo records and then mimics the movements just as they were made.

The whole operation is way simpler than you might think. As [peterbiglab] demonstrates in the video after the break, the servo knows its position thanks to an internal potentiometer on the motor’s rotor. If you locate the pot output pin on the control board and run a wire from there into an Arduino, you can use that information to calibrate and control the servo’s position pretty easily. There are a ton of possibilities for this kind of control. What would you do with it? Let us know in the comments.

If you want to try this with a bunch of servos at once, might as well build yourself a little testing console.

Continue reading “Simon Says, But With Servos” →

Offline Dinosaur-Jumping Becomes A Real Workout

April 6, 2020 by Kristina Panos 16 Comments

It’s great to see people are out there trying to find fun ways to exercise amid the current crisis. Although jumping up and down isn’t great for the knees, it does give decent cardio. But if you don’t have a rope or a puddle, we admit that jumping can lose its bounce pretty fast.

Quarantine has been a game-filled time for [fridaay]. Somewhere between a handful of FPS games, he decided to try to play Google’s offline dinosaur-based side scroller game by making the dinosaur spring over the saguaros whenever he physically jumps in the air. (Video, embedded below.)

Here’s how it works: [fridaay] holds a transmit circuit that consists of an Arduino UNO, an accelerometer module, and an nRF24L01 transceiver, all running on a 9 V battery. Whenever [fridaay] jumps, the accelerometer reads the change in Z and sends it to the receiving circuit, which is just another UNO and nRF. The receiving UNO is connected to a laptop and configured to press the space bar so the dinosaur canters over the cacti.

We’ve never been able to stay alive long enough in the game to see this happen, but apparently you need to crouch at some point in the game. [fridaay] has yet to implement a control for that, but we’re sure he’ll think of something. Jump past the break to see the video, and hit him up if you need the code.

If you have a lot of parts at your disposal, why not make a physical version?

Continue reading “Offline Dinosaur-Jumping Becomes A Real Workout” →

An Arduino-Free Automatic Alcohol Administrator

April 5, 2020 by Kristina Panos 30 Comments

With all the hands-free dispenser designs cropping up out there, the maker world could potentially be headed for an Arduino shortage. We say that in jest, but it’s far too easy to use an Arduino to prototype a design and then just leave it there doing all the work, even if you know going in that it’s overkill.

[ASCAS] took up the challenge and built a cheap and simple dispenser that relies on recycled parts and essential electronics. It uses an IR proximity sensor module to detect dirty digits, and a small submersible pump to push isopropyl alcohol, sanitizer, or soap up to your hovering hand. The power comes from a sacrificial USB cable and is switched through a transistor, so it could be plugged into the wall or a portable power pack.

We admire the amount of reuse in this project, especially the nozzle-narrowing ballpoint pen piece. Be sure to check out the build video after the break.

Hopefully, you’re all still washing your hands for the prescribed 20 seconds. If you’re starting to slip, why not build a digital hourglass and watch the pixels disappear?

Continue reading “An Arduino-Free Automatic Alcohol Administrator” →

Data Glove Gets A Grip On Gesture Input

April 5, 2020 by Kristina Panos 3 Comments

If we really want wearable computing to take off as a concept, we’re going to need lightweight input devices that can do some heavy lifting. Sure, split ergo keyboards are awesome. But it seems silly to restrict the possibilities of cyberdecks by limiting the horizons to imitations of desk-bound computing concepts.

What we really need are things like [Zack Freedman]’s somatic data glove. This fantastically futuristic finger reader is inspired by DnD spells that have a somatic component to them — a precise hand gesture that must be executed perfectly while the spell is spoken, lest it be miscast. The idea is to convert hand gestures to keyboard presses and mouse clicks using a Teensy that’s housed in the wrist-mounted box. You are of course not limited to computing on the go, but who could resist walking around the danger zone with this on their wrist?

Each finger segment contains a magnet, and there’s a Hall effect sensor in each base knuckle to detect when gesture movement has displaced a magnet. There’s a 9-DoF IMU mounted in the thumb that will eventually allow letters to be typed by drawing them in the air. All of the finger and thumb components are housed in 3D-printed enclosures that are mounted on a cool-looking half glove designed for weightlifters. [Zack] is still working on gesture training, but has full instructions for building the glove up on Instructables.

It’s true: we do love split ergo keyboarded cyberdecks, and this one is out of this world.

Minimalist Magnetic Minute Minder Mesmerizes

April 3, 2020 by Kristina Panos 26 Comments

Timepieces are cool no matter how simplistic or granular they are. Sometimes its nice not to know exactly what time it is down to the second, and most of the really beautiful clocks are simple as can be. If you didn’t know this was a clock, it would still be fascinating to watch the bearings race around the face.

This clock takes design cues from the Story clock, a visual revolution in counting down time which uses magnetic levitation to move a single bearing around the face exactly once over a duration of any length as set by the user. As a clock, it’s not very useful, so there’s a digital readout that still doesn’t justify the $800 price tag.

[tomatoskins] designed a DIY version that’s far more elegant. It has two ball bearings that move around the surface against hidden magnets — an hour ball and a minute ball. Inside there’s a pair of 3D-printed ring gears that are each driven by a stepper motor and controlled with an Arduino Nano and a real-time clock module. The body is made of plywood reclaimed from a bed frame, and [tomatoskins] added a walnut veneer for timeless class.

In addition to the code, STLs, and CAD files that birthed the STLs, [tomatoskins] has a juicy 3D-printing tip to offer. The gears had to be printed in interlocked pieces, but these seams can be sealed with a solution of acetone and plastic from supports and failed prints.

If you dig minimalism but think this clock is a bit too vague to read, here’s a huge digital clock made from small analog clocks.