Keep Your Lungs Clean And Happy With A DIY Supplied-Air Respirator

July 9, 2024 by 13 Comments

The smell of resin SLA printing is like the weather — everybody complains about it, but nobody does anything about it. At least until now, as [Aris Alder] tackles the problem with an affordable DIY supplied-air respirator.

Now, we know what you’re thinking, anything as critical as breathing is probably best left to the professionals. While we agree in principle, most solutions from reputable companies would cost multiple thousands of dollars to accomplish, making it hard to justify for a home gamer who just doesn’t want to breathe in nasty volatile organic compounds. [Aris] starts the video below with a careful examination of the different available respirator options, concluding that a supplied air respirator (SAR) is the way to go.

His homebrew version consists of an affordable, commercially available plastic hood with a built-in visor. Rather than an expensive oil-free compressor to supply the needed airflow, he sourced a low-cost inline duct fan and placed it outside the work zone to pull in fresh air. Connecting the two is low-cost polyethylene tubing and a couple of 3D printed adapters. This has the advantage of being very lightweight and less likely to yank the hood off your head, and can be replaced in a few seconds when it inevitably punctures.

Another vital part of the kit is a pulse oximeter, which [Aris] uses to make sure he’s getting enough oxygen. His O2 saturation actually goes up from his baseline when the hood is on and powered up, which bodes well for the system. Every time we pick up the welding torch or angle grinder we wish for something like this, so it might just be time to build one.

Continue reading “Keep Your Lungs Clean And Happy With A DIY Supplied-Air Respirator” →

Solar Dynamics Observatory: Our Solar Early Warning System

July 9, 2024 by 3 Comments

Ever since the beginning of the Space Age, the inner planets and the Earth-Moon system have received the lion’s share of attention. That makes sense; it’s a whole lot easier to get to the Moon, or even to Mars, than it is to get to Saturn or Neptune. And so our probes have mostly plied the relatively cozy confines inside the asteroid belt, visiting every world within them and sometimes landing on the surface and making a few holes or even leaving some footprints.

But there’s still one place within this warm and familiar neighborhood that remains mysterious and relatively unvisited: the Sun. That seems strange, since our star is the source of all energy for our world and the system in general, and its constant emissions across the electromagnetic spectrum and its occasional physical outbursts are literally a matter of life and death for us. When the Sun sneezes, we can get sick, and it has the potential to be far worse than just a cold.

While we’ve had a succession of satellites over the last decades that have specialized in watching the Sun, it’s not the easiest celestial body to observe. Most spacecraft go to great lengths to avoid the Sun’s abuse, and building anything to withstand the lashing our star can dish out is a tough task. But there’s one satellite that takes everything that the Sun dishes out and turns it into a near-constant stream of high-quality data, and it’s been doing it for almost 15 years now. The Solar Dynamics Observatory, or SDO, has also provided stunning images of the Sun, like this CGI-like sequence of a failed solar eruption. Images like that have captured imaginations during this surprisingly active solar cycle, and emphasized the importance of SDO in our solar early warning system.

Continue reading “Solar Dynamics Observatory: Our Solar Early Warning System” →

Samsung Killed The Online Service, This 20 Dollar Dongle Brings It Back

July 9, 2024 by 14 Comments

Around 2010 or so, Samsung cameras came with an online service: Social Network Services. It enabled pictures to be unloaded wirelessly to social media with minimum hassle, which back then wasn’t quite as easily accomplished as it is today. Sadly they shuttered the service in 2021, leaving that generation of cameras, like so many connected devices, orphaned. Now along comes [Ge0rG] with a replacement, replicating the API on a $20 LTE dongle.

The dongle in question is one we featured a couple of years ago, packing a Linux-capable computer of similar power to a Raspberry Pi Zero alongside its cell modem. The camera can connect to the device, and a photo can be sent in a Mastodon post. It’s something of a modern version of the original, but for owners of the affected cameras it’s a useful recovery of a lost service.

It’s surprising in a way that we’ve not heard of more hacks using these dongles, as they do represent a useful opportunity. That we haven’t should be seen as a measure of the success of the Raspberry Pi and other boards like it, just as it’s no longer worth hacking old routers for Linux hardware projects, so there’s less of a need to do the same here.

Making EV Motors, And Breaking Up With Rare Earth Elements

July 9, 2024 by 85 Comments

Rare earth elements are used to produce magnets with very high strength that also strongly resist demagnetization, their performance is key to modern motors such as those in electric vehicles (EVs). The stronger the magnets, the lighter and more efficient a motor can be. So what exactly does it take to break up with rare earths?

Rare earth elements (REEs) are actually abundant in the Earth’s crust, technically speaking. The problem is they are found in very low concentrations, and inconveniently mixed with other elements when found. Huge amounts of ore are required to extract useful quantities, which requires substantial industrial processing. The processes involved are ecologically harmful and result in large amounts of toxic waste.

Moving away from rare earth magnets in EV motors would bring a lot of benefits, but poses challenges. There are two basic approaches: optimize a motor for non-rare-earth magnets (such as iron nitrides), or do away with permanent magnets entirely in favor of electromagnets (pictured above). There are significant engineering challenges to both approaches, and it’s difficult to say which will be best in the end. But research and prototypes are making it increasingly clear that effective REE-free motors are perfectly feasible. Breaking up with REEs and their toxic heritage would be much easier when their main benefit — technological performance — gets taken off the table as a unique advantage.

Going Ham Mobile On A Bicycle

July 8, 2024 by 19 Comments

It’s said that “Golf is a good walk spoiled,” so is attaching an amateur radio to a bike a formula for spoiling a nice ride?

Not according to [Wesley Pidhaychuk (VA5MUD)], a Canadian ham who tricked out his bike with a transceiver and all the accessories needed to work the HF bands while peddling along. The radio is a Yaesu FT-891, a workhorse mobile rig covering everything from the 160-meter band to 6 meters. [Wes] used some specialized brackets to mount the radio’s remote control head to the handlebars, along with an iPad for logging and a phone holder for streaming. The radio plus a LiFePO4 battery live in a bag on the parcel rack in back. The antenna is a Ham Stick mounted to a mirror bracket attached to the parcel rack; we’d have thought the relatively small bike frame would make a poor counterpoise for the antenna, but it seems to work fine — well enough for [Wes] to work some pretty long contacts while pedaling around Saskatoon, including hams in California and Iowa.

The prize contact, though, was with [WA7FLY], another mobile operator whose ride is even more unique: a 737 flying over Yuma, Arizona. We always knew commercial jets have HF rigs, but it never occurred to us that a pilot who’s also a ham might while away the autopilot hours working the bands from 30,000 feet. It makes sense, though; after all, if truckers do it, why not pilots?

Continue reading “Going Ham Mobile On A Bicycle” →

Open Source High Speed SiGe IC Production For Free!

July 8, 2024 by 7 Comments

We’ve covered the Tiny Tapeout project a few times on these pages, and while getting your digital IC design out there onto actual silicon for a low cost is super cool, it is still somewhat limited. Now, along comes the German FMD QNC project funding MPW (multi-project wafer) runs not in bog standard Silicon CMOS but Silicon-Germanium bipolar technology. And this is accessible to you and me, of course, provided you have the skills to design in this high-speed analog technology.

The design can be submitted via Github by cloning the IHP-Open-DesignLib repo, adding your design, and issuing a pull request. If your submission passes the correctness checks and is selected, it will be fabricated in-house by the IHP pilot line facility, which means it will take at least four months to complete.  However, there are a few restrictions. The design must be open source, DRC complete (obviously!) and below a somewhat limiting two square millimetres. Bonus points for selecting your project can be had for good documentation and a unique quality, i.e., they shouldn’t have too many similar designs in the project archive. Also, you don’t get to keep the silicon samples, but you may rent them for up to two years for evaluation. In fact, anybody can rent them.  Still, it’s a valuable service to trial a new technique or debug a design and a great way to learn and hone a craft that is difficult to get into by traditional means. Such projects would be an excellent source of verifiable CV experience points we reckon!

If you fancy getting your hands on your own silicon, but bipolar SiGe is a bit of a stretch, look no further than our guide to Tiny Tapeout. But don’t take our word for it—listen to the creator himself!

Exploded view of a mini PC built into a keyboard.

Keyboard Contains Entire Mini PC, Just BYOD

July 8, 2024 by 52 Comments

When we talk about keyboards that do it all, we usually mean either big ones with lots of keys and doodads like rotary encoders and displays, or small ones with lots of layers (and usually a few doodads, too). But this — this is something else entirely. Chinese PC maker Linglong have crammed an entire mini PC into a keyboard that’s small enough to fit in your back pocket. Oh, and it folds, too. All you need is a display.

Why do you need a display? Why not include one, if you’re going to wedge everything else in there? Well, the company envisions its users pairing it with a VR or AR glasses. But we can see use cases far beyond ownership of special spectacles, of course.

For instance, office work. Linglong says this key-puter (you read it here first) will last up to ten hours for light use, and nearly six hours for watching movies, but heavy use will have you down to four hours, which really isn’t that bad.

Spec-wise, it looks pretty good, with an AMD Ryzen 7 and either 16 or 32 GB of memory and a half- or full-terabyte hard drive. The whole thing is around 4 x 6″ (15 x 10cm), presumably in the folded orientation, and weighs less than two pounds (800 g). The projected cost is $400-500 depending on specs.

Unfortunately, this little key-puter isn’t available just yet. There are just 200 units available for Beta testing, and no, we don’t have one!

Main and thumbnail images via Linglong