Rovio Teardown

October 20, 2008 by Caleb Kraft 5 Comments

[Del] sent us what might be the first in an expected plethora of hacks on the Wowee Rovio. He was annoyed by the poor lighting for Rovio’s camera so he cracked it open and started hacking. He found there was just enough space for a couple LEDs in the head. The most difficult part of this was apparently running the wires for power into the main body of the rovio. He said it took him around 30 minutes just to snake the wires through the neck. The final result is best seen in the comparison pictures of rovio looking at Wall-E.

Jar Of Fireflies

October 18, 2008 by Eliot 14 Comments

[Randomskk] has been attempting to make electronic fireflies for quite some time and finally settled on a design he liked. His jar of fireflies uses an ATtiny13 to control a set of 12 matrixed LEDs. The green SMD LEDs are each soldered to a pair of thin wires that hang down into the jar. The software picks an LED at random to flash and then flashes it 1-3 times. The random seed is incremented each time the jar is turned on, so you’ll get 255 different patterns. The power is just a standard coin cell. The project is fairly simple electrically, but the LED soldering could prove difficult. It was inspired by this firefly jar project. Check out [Alex]’s synchronizing fireflies too. A video of the jar is available below. Continue reading “Jar Of Fireflies” →

LED POV Hard Drive Clock

October 17, 2008 by Caleb Kraft 29 Comments

[Ian Smith] sent us this POV display made from an old hard drive. It works by flashing some LEDs under the platter, which has a line cut in it. Since the platter spins at roughly 90 rotations per second, we perceive a solid image. He was inspired by [Alan Parekh]’s project, but did several things differently. Mounting the LEDs was much simpler in this project as he had a strip of RGB LEDs that came with adhesive tape on the back. He also used a small magnet and a hall effect sensor to measure full rotations instead of an IR beam sensor. Check the video after the break.

Continue reading “LED POV Hard Drive Clock” →

Wireless Accelerometer Controlled RGB LED

October 9, 2008 by Caleb Kraft 10 Comments

[Andlier] sent us this cool little project. He has built a wireless accelerometer controlled RGB LED lighting system. Based on what a mouth full that is, it sounds complicated right? The end result looks fairly intuitive. Simply pick up the controller and tilt your hand to change the color of the light.

The controller consists of an Atmel AVR168 microcontroller. He doesn’t specify what transceiver he is using, but if you look in the comments, he notes that he added an antenna to it to extend the range. The part that controls the LED is based off of an Atmel AVR169 microcontroller hooked to some shiftbright LED modules.

Continue reading “Wireless Accelerometer Controlled RGB LED” →

Animated LED Eyes For Halloween

October 3, 2008 by Caleb Kraft 5 Comments

[Matt Daughtrey] sent us this sweet little project he’s doing for Halloween. He’s building some animated LED eyes. He says that the whole thing is 3 individual LMDriver platforms, another project he’s working on. There isn’t any info available about that, but he does expand a little. He states that each display module uses an Atmega169 with some heavy multiplexing. The eyes really don’t look that impressive sitting on the bench, but watch the video to see how cool they really are.

We noticed that the back of the boards appear to have http://www.embeddedether.net on them. Unfortunately that site seems to have been grabbed by a domain squatter.

A Remote Controlled RGB Light Bulb Lamp

September 28, 2008 by Jason Rollette 9 Comments

RGB just got a lot brighter by using 3x60Watt flood lights instead of an LED. The bulbs are driven via TRIACs and the whole thing uses a remote control to change the levels of the three bulbs. It is also able to store these levels for later recall. The IR receiver was taken from a dead TV set along with its remote control, or a universal remote set to a Phillips TV can be used. The source code and schematic for this project are available.

Email Notification Via An RGB LED

September 28, 2008 by Jason Rollette 15 Comments

This project provides LED feedback when an email is received. It uses a 4d-micro-USB module from Dontronics to interface serially and provide power to a Picaxe 08M. The PIC can control color and brightness of a RGB LED. The feedback is given by seven colors of the LED. The code is python script and picaxe basic, which he’s posted.