Dot Matrix Business Card

September 5, 2008 by Joey Celis 5 Comments

In most settings business cards are given out without much thought. But what if you could make your card stand out from the rest? By using a 5×15 LED matrix screen, a single micro controller, a number of resistors, switches, and other parts, [tomward] has put together one very slick business card that’s sure to draw attention.

The included instructions go into great detail on the construction, but [tomward]admits that you will need some knowledge in electronics in order to build one yourself. After reading the instructions ourselves we would have to agree with him.

If you’re into programing micro controllers and are handy with a soldering iron you may want to give this a shot.

RGB Desktop Clock

September 1, 2008 by Eliot 11 Comments

[youtube=http://www.youtube.com/watch?v=-hxZRCponks&hl=en&fs=1&rel=0][Mark Roy] designed this fine RGB LED desktop clock. It uses a PIC16F877A microcontroller and a DS1307N Real Time Clock. There is a ring of 12 RGB LEDs around the perimeter. Hours are indicated in red, minutes green, and seconds blue. If the hands overlap, the colors are mixed. Three buttons are used to set the time and it can run on as little as 0.7volts. You can find out more about the project on Stellar Core. He has plans to kit it in the future.

Testing IR Camera Blocking

August 27, 2008 by Kimberly Lau 37 Comments

[youtube=http://www.youtube.com/watch?v=0u5hAfnq2-4&hl=en&fs=1&rel=0][randy] from F.A.T. tested the theory that infrared LEDs can actually hide you from the prying eyes of surveillance cameras. We’ve previously covered camouflage, IR, and other suggestions for eluding the cameras, but haven’t taken to sewing stuff onto our clothes yet. [randy] lined his hoodie with high-intensity infrared LEDs, hoping to create a halo effect that would hide his head, and tested his results. Unfortunately, his efforts were unsuccessful. He tested many many different combinations and we’re confident in his conclusion that it would be very hard to make this work.

SMD Soldering Practice Kit

August 24, 2008 by Eliot 9 Comments

Here’s an interesting kit put together just to help you work on your SMD soldering skills. It’s got 49 SMD LEDs on the front with a programming header and switch jumper. The back has an ATtiny26L and a coin cell. At only 3V, power management is essential; all of the example programs are only addressing one LED at a time (imperceptible to the human eye). If you turn on too many LEDs at the same time, the voltage drop could cause the AVR to reset. Included example programs are a scrolling marque, bouncing balls, and Conway’s game of life. SparkFun has tutorials for regular SMD soldering and using a reflow skillet. The video below shows the kit builder attaching just one LED using the heat and slide method.

Continue reading “SMD Soldering Practice Kit” →

LED Floor Captures Digital Footprints

August 14, 2008 by Kimberly Lau 7 Comments

[youtube=http://www.youtube.com/watch?v=NpRE6CM3oOY&hl=en&fs=1&rel=0&color1=0x3a3a3a&color2=0x999999]
Sensacell created a unique interactive flooring system for the 2008 World Expo in Zaragoza, Spain. Comprised of 1000 LED panels, the 250 foot installation is covered in architectural glass and lights up in response to pressure. We like what different people are doing in this clip; from walking in a line to dragging a mop over the floor, the results are undeniably captivating and ultimately irresistible.

[via Gizmodo]

PoiPlay – LED Poi

August 14, 2008 by Caleb Kraft 8 Comments

PoiPlay is an elegant mix of new technology and traditional medium. Poi, Maori for ball, is a traditional form of juggling originating in New Zealand. In poi, a ball at the end of a rope or chain is swung in circular motion to develop visual patterns. Often augmented by flame, and more recently LEDs and glow sticks.

The PoiPlay device has 28 RGB LEDs in a 1 foot long enclosure at the end of a rope. They have a 1mbit per second bidirectional wireless interface, three Atmel processors, a lithium ion battery, and a charger. The base station controls not only the PoiPlay but the music as well. All the control software that resides on the PC was written in Perl and communicates via USB port under Cygwin.

They have built the devices to be individually addressable with the capability of being grouped by subnet. This feature isn’t supported by the software yet, but they say it should be done by the next show in 2009.

The site, while pretty offers very little information. Some construction shots would be fantastic. Go check it out though, the pictures are mesmerizing.

[thanks Jm]

RGB Monome Clone

August 13, 2008 by Caleb Kraft 9 Comments

[Julien Bayle] has posted this great breakdown of building an RGB monome clone. He is a musical performer using Ableton Live. He wanted to do away with the need for a computer screen and found that the monome would have been perfect had it been RGB. So he decided to build his own.

The parts list for the entire project is as follows:

1x Arduino board
4x Sparkfun breakout PCB
4x Sparkfun buttons pads (like our door lock)
4x Sparkfun buttons bezel
64x RGB LEDs common cathode
64x Diodes Small Signal (1N4148)
1x MAX7221 (LED Driver)
1x 74HC164 (8-Bit Serial-In, Parallel-Out Shift Register)
1x 74HC165 (8-Bit Parallel-In, Serial-Out Shift Register)

He also has files for the schematics and source code as well as information on how to assemble and test it.

The RGB aspect is still under development. He is using the LEDMatrix-Serial Interface-RGB from Sparkfun Electronics to run it. It is expensive, but is exactly what he was looking for.

There aren’t very many pictures of the project, and none of the working RGB unit. He makes up for it in sheer information. Many parts have links to manufacturers or support forums. Hopefully he’ll post some pictures and video of the final product soon.