When the first two prototype ingredients listed are paperclips and Post-it notes you know it’s going to be good. The problem: one shower stall at work with numerous co-workers who bike to the office. The solution: a occupancy monitor that is smart enough to know that someone is actually in the room. You know what we’re talking about, a sensor that knows more than whether the door is open or closed. [James] got wise and built a sensor to monitor whether the door is bolted or not. We think this method is far superior to motion-based systems.
This uber-smart sensor is simply a pair of paperclips anchored on a rolled Post-it note substrate and shoved in the receiver on the door jamb. When the bolt is locked from the inside it pushes the paperclips together completing the simple circuit. This is monitored by a Spark Core but will work with just about any monitoring system you can devise. What we’re trying to figure out is how to ruggedize the paper-clip hack which we can’t think will perform well for very long. It looks like there’s room to bore out a bit more inside the receiver hole. Perhaps leaf switch with a 3D printed mounting bracket?
Oh, and kudos on the Ikea food storage container for the enclosure. That’s one of our favorite tricks for hacks which are installed for the long-run.
There have been a few people asking us to do our full teardown of a crowdfunding campaign, this time for Bleen. We’ll get to that, but here’s the TL;DR version: 208 people just threw money away, and right now Indiegogo is ~$3000 richer for doing nothing.
Insipired by a Hacklet, [Chris] documented his retro console build. He started out like most people do with a Raspberry Pi, but found emulating newer consoles like the N64 consumed too much processor time. He moved his build over to custom-assembled hardware with an AMD Micro-ATX board, a drive, and a USB gamepad. It’s beautiful, and much, much more powerful than a Raspberry Pi.
SD card in your Pi died? Of course it did. The problem is you’re not shutting down your Pi correctly. [satya] whipped up a quick project to fix that. One button, a bit of Python, and a shell script is all you need for a one-button shutdown for your Raspberry Pi.
A while ago, [Jan] built an ARM-based modeling MIDI synth that sounds a lot like the old Junos of the 80s. It’s build around the one 8-pin DIP ARM that’s being manufactured, placed between a MIDI jack and a 1/4″ jack. That’s pretty much all the components. [Gritty] plugged it into a Teensy that’s connected to a sequencer. It sounds awesome.
Everyone loves the Spark Core – there are a few floating around the office here. Now there’s a new Spark. It’s called the Photon, and they’re packaging it as a module. There’s an STM32F2 microcontroller and a BCM43362 Wi-Fi transceiver packaged in a nice, FCC certified module. Very cool.
[Stephpalm] had carved a pumpkin for the first time in two decades. Unfortunately, the neighborhood squirrels were all too pleased with her work and devoured it. Her original goal for the jack-o’-lantern was to have its lights controlled over the internet. These hungry critters inspired another project instead – The Jack-’o’-Lantern Squirrel Early Warning System. There have been hacks that have dealt with pesky squirrels before, such as a trap and an automatic water turret, but they didn’t have the ability to post to social media like this system does.
The system consists of a Spark Core, a passive infrared (PIR) sensor, and a piezo buzzer. When the motion sensor is triggered the buzzer sounds, scaring away any peckish creatures lurking nearby. [Stephpalm] used an NPN transistor and 1k-Ohm resistor to provide enough current to drive the buzzer. All of these components were connected using jumper wires and a breadboard that sits on top of the pumpkin. As a nod to her original idea, [stephpalm] then created “Pumpkin Watch Code” and loaded it into the Core. It posts preset messages to a Twitter account every 45 minutes of inactivity or whenever a pesky squirrel is detected. The messages can be personalized for anyone who wants to make one of these themselves.
We wonder if it would be better to place the breadboard inside the jack-o’-lantern and carve out a couple of holes on top for the PIR sensor’s wires to come out of. That would offer some protection from the elements and prevent it from getting knocked over. We think this project could be adapted for many other uses. After the break, see a video of the system in action!
Continue reading “Scare Off Squirrels And Tweet About It With The Jack-O’-Lantern Warning System” →
While there are many ways to produce audible sound, Plasma Speakers have to be one of the coolest. Usually very complex and expensive, we received a tip for a beginners guide to making one of these impressive novelties. Handily included are a set of schematics (one very simple schematic, the other with a few artistic illustrations). There are also a set of warnings, which include sound advice to mind the heat generated by the MOSFETs, as well as making sure that your input signal isn’t too strong. The finished product is fun to listen to, so be sure to check out the example video after the break.
Continue reading “Singing: With Plasma!” →
We love to see educational resources appear. iRobot has put together Starter Programs for Advancement of Robotics Knowledge or S.P.A.R.K to serve as not only education, but amusement with the purpose of getting people interested in robotics. With sections divided into different grade levels, it is obvious that this is mainly meant for school aged kids. There are some games as well to keep them amused when they need a break. We looked around a little bit and it seems that they are still fleshing it out. We hope to see some structured content specifically created for education of youngsters. Right now it is mainly links to other resources.
A leyden jar is basically just a simple home made capacitor. We’ve shown you how to make them before. This, however, is how you make a ridiculously large one. [Nickademuss] used a five gallon bucket to make his leyden jar. That’s five whole gallons of lightning. The video, which you can see after the break, shows it light up the entire room when it lets out a fairly formidable spark. This is dangerous folks, be careful.
Continue reading “Leyden Jar Of DOOM.” →