Capacitive Discharge Spot Welder Update

welder

It seems one of our commenters took great umbrage with [PodeCoet] not documenting his capacitive discharge cutting properly. [PodeCoet] had been waiting till he got the full spot welder working before publishing, but he’s expedited the work after all our whining. Check out his full writeup of the device in its current state. It uses a 1Farad audio cap for storage. A dsPIC monitors all of the voltage sources and regulates charging. A nice touch is the tactile switch on the electrode.

Home Power Monitoring

powermonitor

Reader [john] finished up his home power monitor over the holiday weekend. It uses a pair of current transducers clamped onto the mains. These output 0-3V and are read by the Arduino’s ADC. The Arduino averages samples over a 20 second period, calculates power used, and uploads it using an Ethernet Shield. The shield can’t do DNS lookups, so he uses a WRT54G to negotiate with the remote webserver. He admits that the system could be more accurate; it can’t detect small loads like wall warts. He also says that money could be saved by talking serial to the router instead of over ethernet. Here are the current usage charts.

You can find many power monitor projects like this in out Home Hacks category.

World Smallest TV-B-Gone

uTVBG

The TV-B-Gone has proven to be a dangerous and versatile gadget. At Interactive Matter, they created an even smaller version with more sneaking potential. Called the µTVBG, it packs an entire TV-B-Gone in a 1.4 x 2.5 cm footprint and even has room for a programming header. He found some high-powered surface-mount IR LEDs that would match the original TV-B-Gone’s power. To drive the board, they used a CR1220 button battery on the bottom of the board. The whole thing is smaller than your thumb and should be easier to hide next time you wreak havoc.

Capacitive Discharge Cutting

capacitive discharge cutting

Capacitive discharge cutting provides more control than linear transformer versions. A very large capacitor is charged to a precise voltage and then discharged through the material to produce a controlled cut. The same device can also be used for spot and tab welding. A video of copper roof flashing being cut is embedded below. An example of a linear transformer can be found in our our How-to: build your own spot welder.

Continue reading “Capacitive Discharge Cutting” →

Lego Modded Antenna Tuner

legomoddedtunner

This antenna tuner is controlled remotely using geared motors and legos. The tuner needed to be closer to the antenna for performance reasons. This created a problem; most of the radio gear is inside while the tuner is outside. The gear motors and Legos combine to form a closed loop servo, operating two air core caps and an inductor switch. A control box placed near the radio is hard wired to the modded tuner outside. We would like to see something like this under gesture control using the Wii MotionPlus + Arduino.

Last Day To Preorder Your Bus Pirate

Bus Pirate banner by Aaron Silber http://theajblog.com/

Update, Saturday July 4th, 2009: All preorders are closed.

Today is the last day to pre-order a Bus Pirate. Get your own Bus Pirate, fully assembled and shipped worldwide, for only $30. We don’t plan to make more soon, this could be your last chance.

A special shout out to our partner, Seeed Studio, who handled the rush of orders like pros. The first pre-order is already being manufactured, and will ship as soon as possible. Seeed still has a few V2a PCBs if you’d like to roll your own Bus Pirate.

You’ve made this pre-order a huge success, and we’d like to make more projects available in the future. Were you just interested in the Bus Pirate? Should we arrange pre-orders of future Hack a Day hardware? Are there any past projects that we should revisit?

Continue reading “Last Day To Preorder Your Bus Pirate” →

Tiniest Bot, Sort Of. CNC Controlled

tinybot

Here’s an interesting concept, the bot pictured above has no internal control mechanisms.  His claims to have built the smallest bot are dubious, considering it requires a much larger control platform to function, so lets just set that aside and look at how it works. The bot itself is basically a hollow box with a hinged manipulator mounted on it. He has then built a modified CNC type structure with various magnets below a platform. The magnets can move the bot and control the manipulator (assuming the bot isn’t trying to pick up anything magnetic). He talks about this being a possible control scheme for smaller bots, though we think he would have to make some major advancements to his magnetic controls for accuracy’s sake. As for his claims of being the smallest, well, we’re sure we’ve seem similarly sized bots, even hexapods,  that were completely self contained.