Guitar Hero Strum Bar As Guitar Kill Switch

September 3, 2009 by Mike Szczys 20 Comments

guitar_hero_killswitch

[Ray] had a Guitar Hero controller for PlayStation 2 sitting around. Because he moved on to playing the game on Xbox 360, he decided to cannibalize the older controller for its parts. He removed the strum bar and fit it inside of a mid-1980’s Peavy Patriot electric guitar. Once wired up, it works as a kill switch; it stops all sound from making it to the amp whenever the strum bar switch is actuated. Don’t miss hearing this effect in the video after the break and keep sending in those Guitar Hero mods. Continue reading “Guitar Hero Strum Bar As Guitar Kill Switch” →

Custom Cable Management

August 31, 2009 by Jakob Griffith 19 Comments

3386152715_53461c9c30

You would be hard pressed to find a hacker who doesn’t have in some form a rats nest of wires and cables behind their computer desk. [Antoine] decided to tackle the problem and came up with his custom built cable management system. There is little info, but he does say his setup uses Ikea Antonius coat hangers and some hollow tube. Its quick and wont leave a residue like some cable solutions, so long as you don’t mind a screw hole or two. We especially like how if you need to change your setup you wont have to re-zip tie everything.

USB Gameboy Cart

August 28, 2009 by Zach Banks 20 Comments

gamecart

[Jose Torres] sent in his latest attempt at creating a custom Gameboy game cartridge. We’ve featured his projects before, and he’s come a lot closer over the last 2 years. He’s aiming to create an easy interface for homebrewers that doesn’t require any other special equipment. In this revision, he’s using a PIC and a memory controller to interface between an SD card and the Gameboy. The cart also has USB support for uploading files to the SD card and reprogramming the PIC. Because it’s just USB mass storage, it will work on almost any modern OS. He’s currently testing the device, but hopes to be selling them soon for $40.

Interfacing A Digital Rotary Switch

August 27, 2009 by Mike Szczys 19 Comments

digital_rotary_switch

[hw640] has put together a well written and detail packed explanation of how to interface with a digital rotary switch. These digital opto encoders have just two outputs with four possible logic levels (00, 10, 11, 01). The relative position of the switch is insignificant but the direction of rotation is what matters.

The short and dirty: Each of the switch’s 2 output pins is attached to a pin change interrupt on the microcontroller. Every time the switch moves it generates either a rising edge or a falling edge on one of the two pins; both edges cause an interrupt. By checking which pin caused the interrupt, then comparing the logic levels of the two pins after that interrupt, we can determine the direction the switch was rotated.

Although this explanation uses a PIC and code written in PicBasic Pro the concepts are discussed in the abstract and would easily be adapted to an AVR or another microcontroller of your choice.

Adding A DisplayLink Monitor To A Linux Router

August 24, 2009 by Matt Schulz 14 Comments

slugterm_dl

Routers aren’t just for routing network traffic any more. With the help of alternative operating systems such as DD-WRT, Tomato, and OpenWrt, routers are now extremely customizable and can be utilized to suit a number of needs. The main issue with projects built around routers is the need to telnet or SSH into them to get to a console. [Sven Killig] came up with a useful solution that utilizes the USB ports available on an Asus router to display video on a DisplayLink device, allowing a user to sit down and use the device as though it were a physical terminal. This would be a good DIY alternative to commercially available routers that display network graphs, system information, incoming email, and other data.

Klipsch Speaker Mods

August 23, 2009 by Caleb Kraft 8 Comments

P1010021 (Custom)

[Patrick] has a pair of Klipsch speakers that continually needed the volume knob cleaned. After a bit of research, he found it was a common problem with the potentiometer chosen for the task. He decided to resolve the problem, not by replacing that potentiometer, but by modifying the speakers to be passive and running them from an external amp. While this does sound simple at first, he wanted to retain the rest of the electronics in the unit, so a bit of hacking was required. You can follow along through the whole process on his site.

Second Hard Drive In A Macbook Pro

August 23, 2009 by Caleb Kraft 23 Comments

Picture 4 (Custom)

[Reid] wrote in to show us how to add a second hard drive to his Macbook Pro. He found that he hardly ever used his DVD drive, so sacrificed it in favor of added storage. What he found was that it had a proprietary adapter that he was unable to find for sale anywhere. Making an adapter may seem like a pretty simple hack, but this could save some people considerable time. Its also worth noting that upgrading the firmware got him an 18% speed increase, so don’t ignore those updates. We don’t see too many mac hacks around here, you may recall the mac tablet hacks and the logo monitor.