Amplifying The Body’s Own Electricity

December 29, 2015 by Bil Herd 11 Comments

Measuring the body’s electrical signals is a neat trick… if you can get your equipment dialed in enough to establish dependable measurements. The technique is called Surface ElectroMyography (SEMG) though you’ll hear many call this ECG. They’re essentially the same technology; the Electro CardioGraph instruments monitor the activity of the heart while SEMG Instruments monitor electrical signals used to control other muscles. Both types of hardware amount to an instrumentation type amplifier and some form of I/O or display.

This topic has been in my back pocket for many months now. Back in May we Hackaday’ites descended on New York City for the Disrupt NY Hackathon event. We arrived a day or so early so that we might better peruse the Korean BBQ joints and check out the other electronics that NY has to offer. On Saturday we gathered around, each shouting out the size of his or her t-shirt preference as we covered up our black Hackaday logo tees with maroon maroon ones (sporting the Hackaday logo of course) for a 24-hour craze of hardware hacking.

There were two individuals at our tables who were both hacking away on hardware to measure the electrical field produced by the body’s muscles in some form or another. The electrical signals measured from the skin are small, and need careful consideration to measure the signal despite the noise. This is a fun experiment that lets you work with both Instrumentation Amplifiers and OpAmps to achieve a usable signal from the movement of your body.

Continue reading “Amplifying The Body’s Own Electricity” →

Blacksmith Forge Made From The Bathroom Sink

November 4, 2015 by Bil Herd 57 Comments

The sweltering heat had finally moved on and Giant Tick season was coming to a close (not kidding, they are HUGE here), when I decided to fire up my hacked together blacksmith forge made out of an old bathroom sink and aquarium stand.

In the age-old formula I needed to supply an air source to a fuel to create enough heat to make iron malleable. I got the idea that this particular bathroom sink might be a good candidate for a fire bowl after I banged my shin with it and then cursed at it. It was clearly made of cast iron and as proof it was clearly unfazed by my tirade of words which I hope my son has learned from the Internet and not from listening to me remodel the bathroom.

Continue reading “Blacksmith Forge Made From The Bathroom Sink” →

Programmable Logic: Build Yourself A CPLD Module

October 28, 2015 by Bil Herd 80 Comments

A Complex Programmable Logic Device (CPLD) is a great piece of hardware to have in your repertoire. As its name implies, you can program these chips to serve the logic functions you need. This might be replacing an obsolete chip, or maybe just a way to learn and try different techniques. What better way to learn than to get your hands on a CPLD and give it a try?

I created a CPLD module with the intent of being able to plug it into lots of things including solderless breadboards, but I screwed up. It seems that the plugin space available on a solderless breadboard is 1.1”, I had made the footprint 1” wide leaving no room for a row of wires on both sides. Duh.

But let me back up and show more about what I’m doing , I wanted to make a programmable piece of logic that could be built as a kit one could easily solder at home, could be programmed in-circuit, and could work at 3.3 or 5 volts.

To implement an easily solderable kit I went with an older CPLD part that also has 3.3v and 5v versions that will maintain its programming regardless of power. The logic itself is a CPLD IC from the Altera Max family with two versions that fit the board with either 32 or 64 macrocells. A macrocell is the basic logic building block and it is programmed with logic “terms” and then interconnected to other macrocells through a programmable interconnect.

Continue reading “Programmable Logic: Build Yourself A CPLD Module” →

Learn And Build A High Side Switch

September 16, 2015 by Bil Herd 75 Comments

As electronics engineer I have a mental collection of circuits that I’ve gathered over the years, much like a mechanic collects specialized tools as they work. All engineers do this and the tools in their tool boxes usually represent their project history and breadth.

A useful circuit to have in designer’s toolbox is the “high side switch”. Like it sounds, this is a circuit that switches the “high side” or positive voltage to a load.

We usually tend to switch things to ground as seen by outputs such as an Open Collector output, the reason being that ground usually is a known entity and is usually low impedance and is at a known voltage. But there are advantages to using a high-side switch in your circuits.

Continue reading “Learn And Build A High Side Switch” →

How CMOS Works: Some Final Words About CMOS

September 2, 2015 by Bil Herd 18 Comments

Finishing up on the topic of CMOS bus logic I am going to show a couple of families with unique properties that may come in handy one day.

High Voltage Tolerant Family: AHC/AHCT

AHCT w/o high side diode — Note the missing diode to VDD

First up is a CMOS logic family AHC/AHCT that has one of the protection diodes on the input removed. This allows a 5V input voltage to be applied to a device powered by 3.3V so that I don’t have to add a gate just for the translation. Any time I can translate and do it without any additional gate delays I am a happy engineer.

Of course the example above works in a single direction and bidirectional does start to get more complicated. Using a bidirectional buffer such as a 74AHCT245 will work for TTL translation when going from 3.3V back to 5V providing there is a direction control signal present.

Continue reading “How CMOS Works: Some Final Words About CMOS” →

How CMOS Works: MOSFETs, JFETs, IGFETS And More

August 3, 2015 by Bil Herd 44 Comments

CMOS opened the door for many if not most of the properties needed for today’s highly integrated circuits and low power portable and mobile devices. This really couldn’t happen until the speeds and current drive capabilities of CMOS caught up to the other technologies, but catch up they did.

Nowadays CMOS Small Scale Integration (SSI) logic families, I.E. the gates used in external logic, offer very fast speeds and high current drive capability as well as supporting the low voltages found in modern designs. Likewise the Very Large Scale Integration (VLSI) designs, or Very Very Large Scale if you like counting the letter V when talking, are possible due to low power dissipation as well as other factors.

Continue reading “How CMOS Works: MOSFETs, JFETs, IGFETS And More” →

CommVEx 2015: What Happens When Commodore Users Gather

July 28, 2015 by Bil Herd 27 Comments

I’m not getting any younger, in fact I’m getting older by the day. This fact along with the fact that this year is the 30^th anniversary of the Commodore C-128 and the original Commodore Amiga prompted me to attend this year’s CommVEx in Las Vegas lest I not be around for the next significant anniversary. For those that don’t know me, I designed the C-128 at the ripe old age of 25 back in 1984-85, though I would ask that you not hold that against me as it was a very long time ago.

Also this year Dr. Leonard Tramiel, son of Commodore’s founder Jack Tramiel, was able to swing by which was an unprecedented and unforgettable event.