Interview: FieldKit Team The Morning After Winning The 2019 Hackaday Prize

December 13, 2019 by Mike Szczys 1 Comment

We caught up with Shah Selbe and Jacob Lewallen the morning after their project, FieldKit, won the Hackaday Prize. FieldKit is an open-source field-based research data collection platform. Which is basically a lot of fancy words for saying it’s a system for collecting sensor data in the field without being snagged by the myriad of problems associated with putting electronics in remote locations. It’s a core project of Conservify, a non-profit organization that seeks to empower conservation research.

As grand prize winner the FieldKit project was awarded a $125,000 cash prize, which Shah and Jacob say is transformative for a non-profit pursuing technology research and development. It seems the grant process has not evolved to embrace developing electronics, while opportunities for research projects have begun to involve recording large data sets in order to test a hypothesis. This is where FieldKit truly shines. Their vision is to provide a low-cost and extensible system that other researchers can use to collect data while making their own grant dollar go much further.

Continue reading “Interview: FieldKit Team The Morning After Winning The 2019 Hackaday Prize” →

Reflection On A Decade Of Hackerspace Expansion

December 13, 2019 by Jenny List 44 Comments

A few days ago I was invited to a party. Party invites are always good, and if I can make it to this one I’ll definitely go. It’s from a continental European hackerspace, and it’s for their tenth birthday party. As I spent a while checking ferries and flights it struck me, a lot of the spaces in my sphere are about a decade old. I went to London Hackspace’s 10th earlier in the year, and a host of other British hackerspaces aren’t far behind. Something tells me I’ll be knocking back the Club Mate and listening to EDM of some form at more than one such party in the coming year.

For most of the decade since I found the then-recently-established mailing list of my local hackerspace I’ve spent a lot of my time involved in more than one space. I’ve been a hackerspace director, a member, and many roles in between and I’ve seen them in both good times and bad ones. Perhaps it’s time to sit back and take stock of that decade and ask a few questions about hackerspaces. How have they fared, what state are they in now, and where are they going?

Continue reading “Reflection On A Decade Of Hackerspace Expansion” →

Hackaday Podcast 046: Bring Us Your Nonsense, Hacking NES Clones, Grasping FPGAs, Many A Music Hack, And Fish Tanks Full Of Random

December 13, 2019 by Mike Szczys 4 Comments

Difference of two Vikram moon images, contrast tweaked.

Hackaday editors Elliot Williams and Mike Szczys highlight the most delightful hacks of the past week. Need a random-number showpiece for your office? Look no further than that fish tank. Maybe the showpiece you actually need is to complete your band’s stage act? You want one of Tristan Shone’s many industrial-chic audio controllers or maybe just a hacked turntable sitting between your guitar and amp.

Plus citizen science is alive and well in the astronomy realm, and piezo elements are just never going to charge your electric vehicle.

Take a look at the links below if you want to follow along, and as always tell us what you think about this episode in the comments!

Take a look at the links below if you want to follow along, and as always, tell us what you think about this episode in the comments!

Direct download (60 MB or so.)

Continue reading “Hackaday Podcast 046: Bring Us Your Nonsense, Hacking NES Clones, Grasping FPGAs, Many A Music Hack, And Fish Tanks Full Of Random” →

3D Printed Metro Charger Ready For The Wasteland

December 13, 2019 by Tom Nardi 21 Comments

In the video game Metro 2033 and its subsequent sequels, players fight their way through a post-apocalyptic version of Russia using improvised weapons and tools cobbled together from the sort of bits and bobs the survivors of a nuclear war might be able to scavenge from the rubble. One of the most useful devices in the game is known as the “Universal Charger”: a hand-operated dynamo that the player must use periodically recharge their electrical devices.

Being a fan of the series, [Nikola Petrov] wanted to build his own version of the Metro 2033 charger; but rather than going for an exact screen replica, he decided to explore the mechanism itself and see if he could 3D print a functional device.

As demonstrated in the video after the break, his charger manages to produce enough energy to light an LED on each squeeze of the trigger. Though if we were packing our gear to go fight mutated beasties in alternate-future Moscow, we might look for something with a bit more kick.

Beyond the 3D printed parts, the charger uses a couple short pieces of 8 mm rod, a NEMA 17 stepper motor, and a one-way bearing that’s usually used for pull starting small gasolene engines.

Interestingly, [Nikola Petrov] is no stranger to 3D printed electrical generation. If you’re interested in getting some real power out of a NEMA 17 stepper, his fantastic printed wind turbine is a must-see.

Continue reading “3D Printed Metro Charger Ready For The Wasteland” →

This Week In Security: VPNs, Patch Tuesday, And Plundervault

December 13, 2019 by Jonathan Bennett 11 Comments

An issue in Unix virtual private networks was disclosed recently, where an attacker could potentially hijack a TCP stream, even though that stream is inside the VPN. This attack affects OpenVPN, Wireguard, and even IPSec VPNs. How was this possible? Unix systems support all manner of different network scenarios, and oftentimes a misconfiguration can lead to problems. Here, packets sent to the VPNs IP address are processed and responded to, even though they are coming in over a different interface.

The attack initially sounds implausible, as an attacker has to know the Virtual IP address of the VPN client, the remote IP address of an active TCP connection, and the sequence and ACK numbers of that connection. That’s a lot of information, but an attacker can figure it out one piece at a time, making it a plausible attack. Continue reading “This Week In Security: VPNs, Patch Tuesday, And Plundervault” →

3D-Printer And CNC Make This Russian Calculator Bilingual

December 13, 2019 by Dan Maloney 11 Comments

Let’s be clear right up front: there are probably more obvious solutions to the problem of using a Russian calculator when you don’t speak Russian than printing new keys and engraving translated markings on them. But easy solutions are boring and generally considered beyond the scope of Hackaday articles, so let’s dive in.

They say that mathematics is the universal language, but that’s only true to an extent. Still, even with our ~~limited~~ non-existent Cyrillic skills, the Russian keyboard on this RPN calculator isn’t that hard to figure out. But as [Amen] points out, in the midst of fevered calculations, one prefers not to mentally translate Χ→П to STO or remember that В↑ is the Enter key. So he printed a set of replacements for the confusing keys from PLA. While pondering how to safely fixture such small parts for the later engraving step, [Amen] hit on a genius solution: move the print bed to the CNC router and fixture everything in one go. The resulting characters are large enough to be legible and deep enough to be filled with air-drying polymer clay for contrast. After sanding and polishing, the calculator looks like it came from the Министерство электронной промышленности that way.

Honestly, we’d love to get a look inside this calculator. The insides of Russian electronics can be fascinating, and we’ve even seen entire forums dedicated to decapping Russian parts. But we understand the desire to keep it intact.

Continue reading “3D-Printer And CNC Make This Russian Calculator Bilingual” →

Feeding Both Filament And Electrons Through A Custom D-Sub Connector

December 13, 2019 by Danie Conradie 28 Comments

We sometimes forget that 3D printers are just CNC platforms with a hotend attached, and there a whole range of alternative tool heads to use. [Jón Schone] has been doing exactly that, and needed a way to quickly disconnect his hotend completely from his printer, so he 3D printed his own custom D-sub connector for both filament and wires. (Video, embedded below.)

[Jon] has added a number of upgrades for his Creality CR10 3D printer, including a quick change tool mount to allow him to also use a laser engraver and even a small spindle. When the hotend is removed there’s no way to quickly disconnect the wiring , so the print head is usually left connected and placed to one side of the printer. For a quick detach solution for both wiring and the Bowden tube, he first modified an off-the-shelf D-sub connector. The connector was relatively expensive, and the tube had a tendency to pop out, which led to some failed prints.

[Jon] wanted to use proper Bowden tube fittings inside the connector, so he designed and printed his own D-sub connector and bought loose contacts. Pushing the contacts into the housing turned out to be quite difficult to do without breaking them, so he’s working on making that process simpler. This is just one of many examples of 3D printing 3D printer upgrades, which has been a core feature of the RepRap project right from the beginning. Check out the video after the break

We have no shortage of 3D printer hacks and there will be many more to come. Some cool recent ones includes the Jubilee CNC that was built from the start with automatic tool changing in mind, and a printer that fits in your backpack. Continue reading “Feeding Both Filament And Electrons Through A Custom D-Sub Connector” →