Parts: Unboxing The Bus Pirate

July 20, 2009 by Ian 43 Comments

bp-unbox-3

For months we’ve used our Bus Pirate universal serial interface tool to demonstrate electronics parts, so it’s only appropriate that the Bus Pirate get it’s own parts post. We recently had a Bus Pirate preorder, and today we received the pre-production Bus Pirate prototype from Seeed Studio. This prototype was mailed just a few days before preorder 1 started to ship, so those packages should start arriving any day.

Follow along as we unbox the prototype Bus Pirate, and connect it to a debugger to determine the PIC24FJ64GA002-I/SO revision that shipped with this board. Use this post to share your own Bus Pirate unboxing experience. Pictures and discussion after the break.

Continue reading “Parts: Unboxing The Bus Pirate” →

Capacitance Sensor Guide (AD7746)

July 18, 2009 by Eliot 20 Comments

capacitive_sensor

[Marcus] has written up his experiences using the AD7746 capacitance sensor. He used the SparkFun breakout board in conjunction with an Arduino. The available Arduino code wasn’t that great so he rewrote it to be easier to understand. The AD7746 is an I2C device that can be continuously read, but this doesn’t mesh well with the Wiring libraries. Additionally, the calibration routine from the data sheet is difficult to understand. He’s included all of the code he used plus a Processing sketch to help visualize the input which will hopefully make your experience with the chip much more smooth.

Parts: I2C Real-time Clock Calendar (PCF8563)

June 26, 2009 by Ian 8 Comments

The PCF8563 is a real-time clock/calendar/alarm chip with an I2C interface. This would be useful in projects where the primary microcontroller doesn’t have enough resources for an interrupt driven clock.

We demonstrate the PCF8563 using the Bus Pirate after the break. For a limited time you can get your own Bus Pirate, fully assembled and shipped worldwide, for only $30.

Continue reading “Parts: I2C Real-time Clock Calendar (PCF8563)” →

How-to: The Bus Pirate V2 With USB

June 25, 2009 by Ian 32 Comments

buspiratev2goii450

Update, Saturday July 4th, 2009: All preorders are closed.

The Bus Pirate is a universal serial interface tool, we use it to test new chips without writing any code. It currently supports most serial protocols, including 1-Wire, I2C, SPI, JTAG, asynchronous serial, MIDI, and more. We added some other features we frequently need, like pulse-width modulation, frequency measurement, voltage measurement, bus sniffers, pull-up resistors, and switchable 3.3volt and 5volt power supplies.

The new v2 family adds USB power and connectivity to the best Bus Pirate design yet. We also reduced the part count and cost wherever possible. If you want to get your hands on some Bus Pirate USB goodness, Seeed Studio has assembled hardware for $30 (including worldwide shipping).

Read about the new design after the break.

Continue reading “How-to: The Bus Pirate V2 With USB” →

Parts: I2C Audio Volume Potentiometer (DS1807)

February 16, 2009 by Ian 7 Comments

ds1807ii

The DS1807 contains two logarithmic digital potentiometers (pots) for audio volume adjustment. Each pot has 64 volume levels plus a mute setting. The volume level of each pot is set over a two-wire I2C serial interface. We’ll show you how to connect and interface the DS1807 below.

Continue reading “Parts: I2C Audio Volume Potentiometer (DS1807)” →

Parts: LTC2631A I2C Digital To Analog Converter

February 9, 2009 by Ian 9 Comments

ltc2640

Linear Technology’s LTC2631A-LZ8 is an 8bit digital to analog converter (DAC) with an I2C interface. This DAC can output 255 different voltages, spaced evenly between 0 and 2.5volts. We previously demonstrated the LTC2640 with a three-wire SPI interface, but this version is controlled with only two signal wires.

Continue reading “Parts: LTC2631A I2C Digital To Analog Converter” →

How-to: Bus Pirate V1, Improved Universal Serial Interface

January 22, 2009 by Ian 65 Comments

front450a

We use the Bus Pirate to interface a new chip without writing code or designing a PCB. Based on your feedback, and our experience using the original Bus Pirate to demonstrate various parts, we updated the design with new features and cheaper components.

There’s also a firmware update for both Bus Pirate hardware versions, with bug fixes, and a PC AT keyboard decoder. Check out the new Hack a Day Bus Pirate page, and browse the Bus Pirate source code in our Google code SVN repository.

We cover the design updates and interface a digital to analog converter below.

Continue reading “How-to: Bus Pirate V1, Improved Universal Serial Interface” →