The EFF’s Privacy Agenda

November 10, 2008 by Eliot 17 Comments

eff_privacy1

With a new administration coming into power, the Electronic Frontier Foundation feels that it’s time for a change (see what we did there). They’ve posted an agenda that covers fixing privacy issues that have come to the forefront in the last eight years. It involves repairing amendments that prevent corporations from being sued for warrantless wiretapping. They would also modernize the Electronic Communications Privacy Act so that it would cover modern technology. The heavily abused State Secrets Privilege needs reform as well. Their final issue is with REAL ID and datafarming that many state governments have already rejected. If even a bit of this gets fixed, we’ll be happy. In any case, it’ll be good to have a more tech focused administration that doesn’t need the internet explained to it in terms of dumptrucks and tubes.

[photo: Jake Appelbaum]

Easy High Voltage Power Supply

November 10, 2008 by Eliot 16 Comments

hv_supply

[rocketman221] wrote up one of the simplest ways to build a high voltage power supply. This one in particular was used on his coilgun. Instead of building a custom circuit, he’s using flash charging boards from disposable cameras. Six 450V 470uF caps are wired in parallel to make up the bank. Two of the charger boards are wired to one switch to initiate the charging process. Four additional boards are wired two a second switch for the second charging stage. The part cost on this is incredibly cheap and it only requires a 3.3V input to reach 450V. The writeup has plenty of warnings about the dangers of high voltage; you need to clean off all flux residue to prevent arcing across the circuit boards. Embedded below is a video of the bank being discharged through several objects. Continue reading “Easy High Voltage Power Supply” →

Autonomous Cookie Monster

November 10, 2008 by Eliot 8 Comments

cookie_monster

[DJ Sures], who built the autonomous Wall-E, is back with another creation. His new autonomous Cookie Monster is certainly an interesting build. He had the cookie monster plush toy already so the first step was to flay the blue beast and insert a skeleton. He used another robot for that. There are two servos for the wheels plus one for each arm and one for the neck. There’s a distance sensor in the mouth. He built a custom board for the PIC18F4685 microcontroller which is running the same 2D mapping code as his previous bot. Check out the video of it in action below. Continue reading “Autonomous Cookie Monster” →

Impressioning At LockCon

November 10, 2008 by Eliot 5 Comments

impressioning

[Steffen Wernéry] has published a video of the impressioning contest at LockCon. We learned about key impressioning at this year’s HOPE conference. You start the process by inserting a key blank into the lock. By turning the lock until it stops and then moving the key up and down you create marks on the blank’s face. Take a file to those marks to remove the extra material and then repeat the process. Once the pins are set properly, they’ll stop leaving marks on the blank. It takes a lot of skill to do this right, but you end up with a perfectly functional key. [Barry Wels] managed to win the competition in 5:30 with second place coming in at 6 minutes.

Kill A Watt Teardown

November 10, 2008 by Eliot 16 Comments

killawatt

Come on, folks. If we keep tearing apart everything that’s handed to us, we’ll never get nice things. SparkFun got their mitts on two Kill A Watts and proceeded to plug them into everything and then dismantled them to see how they work. The Kill A Watt keeps track of how much power is used over time. The largest load they found was their soda machine using 500W (should probably add a motion sensor to that). They plugged a meter on either side of a UPS and found out that it uses 5W just to charge. On the inside of the meter, there isn’t anything too substantial. One unlabeled IC runs the whole show.

Functional Etch A Sketch Costume

November 9, 2008 by Eliot 5 Comments

etchasketch

We love all of the creative Halloween costumes that have started trickling in now that the holiday is finally over, and people have found time to document their last minute projects. Take this functional Etch A Sketch costume made by [mazinbenny]. The knobs are lawnmower wheels. The pulley system is strung with 1/16″ wire rope to move a carrier for a dry erase marker. The marker draws directly on an acrylic screen. HowStuffWorks has a post on how a real aluminum powder based Etch A Sketch works.

We’ve covered more technical Etch A Sketch projects in the past. We’ve seen them hooked up to computer mice, drawing portraits at Maker Faire, and commenters have even suggested turning mechanical dry erase boards into giant Etch A Sketches.

Dean Kamen’s Stirling Engine Car

November 9, 2008 by Eliot 28 Comments

kamen_car

[Dean Kamen]’s company, the people behind the Segway, have created a hybrid car that uses a Stirling engine instead of a standard internal combustion engine. Stirling engines are closed cycle, meaning heat is applied to the outside of the cylinder walls. They are generally more efficient than standard car engines, but haven’t been used much outside of industrial applications. We suspect that the drivetrain arrangement is similar to the Chevy Volt where the engine is used to charge batteries which are in turn driving an electric motor. This is different from modern hybrids that can have either electric motor or gas engine driving the wheels. The article is unfortunately full of classic [Kamen] hyperbole and minimal detail. He calls the Stirling engine “an insurance policy” for the electric car since it can recharge the battery. That’s right, folks. If you run out of juice, you can put gas in the car. I doubt many Prius owners will fall out of their chair over that. Being a Stirling engine, we’d be more impressed if you could charge the thing by rubbing warm toast on it.

[via Make]